Merge remote-tracking branch 'quic/msm-4.14' into dev/msm-4.14-display

* quic/msm-4.14:
  mhi: dev: uci: do not exceed maximum transfer size supported by mhi host
  mhi: dev: uci: chain large transfers together
  msm: msm_bus: add support for device driver to register with msm bus
  pinctrl: qcom: spmi-gpio: Fix the GPIO strength mapping
  ARM: dts: msm: Disable ATOS feature for smmu for sm8150
  iommu: arm-smmu: Standardize ATOS disablement feature
  usb: dwc3: debug: Add dbg_log_string to log strings
  usb: dwc3: Notify super speed phy about link training
  mhi: core: add support to get external modem time
  ARM: dts: msm: Add default bootdevice as ufs for SM6150
  ARM: dts: msm: Add coresight nodes for SM6150
  msm: kgsl: Correct the iommu protection ranges
  sched: walt: fix updating stale window_start for walt load
  msm: vidc: refine encoder workload calc
  msm: ipa: add a missing mutex unlock for IMP
  ARM: dts: msm: Set offlinable memory limit and granule for sm8150
  arm64: Make section size configurable for memory hotplug
  mm/memory_hotplug: Add hot-added memory blocks to ZONE_MOVABLE type
  arm64: Force non-block mappings for memory hotplug
  arm64: Override memory limit set by boot parameter
  soc: qcom: mem-offline: Dynamic Memory Region Offline driver
  defconfig: sm8150: Enable VTI config for v4 and v6
  defconfig: msm: Enable LLCC driver for sdmmagpie
  drivers: soc: qcom: Add sdmmagpie SoC llcc driver
  defconfig: msm: Enable SDMMAGPIE pinctrl
  ARM: dts: msm: Add device tree node for sdmmagpie pinctrl
  pinctrl: qcom: Add support for sdmmagpie SoC pin control
  soc: qcom: Add support for sdmmagpie into socinfo driver
  defconfig: msm: Select ARCH_SDMMAGPIE in sdmsteppe defconfig
  ARM: dts: msm: Add initial device tree for sdmmagpie
  sdmmagpie: Add initial config option and documentation
  clk: qcom: clk-pll: Add support for HF PLLs clock ops
  clk: qcom: Add CPU clock driver for QCS405
  input: touchscreen: shutdown ST touch's  power supply when suspend
  input: touchscreen: clean kernel log for ST touch
  arm: psci: add psci_cpu_can_disable() function
  ARM: dts: msm: Add lpass and turing pil node for QCS405
  defconfig: qcs405: Remove perf defconfig for qcs405
  wil6210: support Talyn specific board file
  wil6210: support configurable board file via sysfs
  wil6210: use country specific board file upon reg domain change
  phy: ufs: Update UFS PHY calibration sequence
  can: Unified driver for CAN controller
  clk: qcom: Add support for BRANCH_HALT_SKIP flag for branch clocks
  nl80211: Introduce scan flags to emphasize requested scan behavior
  nl80211: add an option to allow MFP without requiring it
  nl80211: add OCE scan and capability flags
  ARM: dts: msm: Update HS PHY parameters for QRD8150
  msm: camera: sensor: Validate power settings
  wil6210: Set default 3-MSI
  wil6210: add 3-MSI support
  ARM: dts: msm: Add coherent test devices and update sids for sm6150
  msm: camera: jpeg flush function cleanup
  msm: camera: isp: Dynamic update of epoch0 line config
  msm: camera: reqmgr: Validate inject delay for all pd devices
  msm: camera: eeprom: Correct free call for power settings
  msm: camera: CSIPHY: Correct register settings for CPHY mode
  msm: camera: crm: Access the task list of workqueue with locks
  msm: camera: lrme: fix return value in error condition
  msm: vidc: Enable decode batching feature
  msm: camera: isp: Define new callback for early PCR
  icnss: Consider recovery as FW down
  defconfig: sdm: Add PIL/SSR support in SM6150

Change-Id: I7cec71c4cb800c63d2d2359462f6500d52b228b9
Signed-off-by: Namratha Siddappa <namratha@codeaurora.org>