DOWNSTREAM commit '90c19c17' from AU415 into msm-4.14-display
* commit '90c19c17': ARM: dts: msm: set default state of pin BT_EN to low for sm8150 ARM: dts: msm: Change QSEE IRQs to level trigger for sm8150 ARM: dts: msm: Add Qseecom heap for sdxprairie ARM: dts: msm: add support for rm69298 truly amoled fhd+ panel to sdmmagpie ARM: dts: msm: Disable FSA switch and Rotator for SA6155 devices ARM: dts: msm: Set default state of cts/rx into bias-disable ARM: dts: msm: enable DP support on SA6155 & SA6155P ARM: dts: msm: add regulators in Bluetooth node for SA8155 ARM: dts: msm: rectify definition of power pins for LGA module ARM: dts: msm: add bluetooth chip device node for SA6155p msm: kgsl: Ensure CX GDSC is off in SLUMBER for RGMU ARM: dts: msm: Enable WDSP SVA for sdmmagpie external codec clk: qcom: gcc: Update clock flags and frequencies for SDXPRAIRIE defconfig: sdxprairie: Enable qseecom driver arm64: defconfig: enable CNSS2 driver on SA6155 configs usb: gadget: f_fs: Fix NULL reference in ffs_func_bind() spmi: spmi-pmic-arb: Fix hw_irq overflow dwc3-msm: Log link TRB address and also readback ring doorbell register ARM: dts: msm: Add USB PHYs configuration on sdxprairie soc: qcom: qsee_ipc_irq_bridge: Remove extra level irq handling soc: qcom: qsee_ipc_irq: Change to level trigger irq msm: ipa: debug out of sync between poll mode and IEOB isr mask soc: qcom: dfc: Correct element size of query response ARM: dts: msm: Remove duplicate dts file for QCS405 variant ARM: dts: msm: Update the IPA IMEM region for sdmmagpie ARM: dts: msm: Update the IPA IMEM region for SM6150 msm: adsprpc: Validate buffer pointer before flush ARM: dts: msm: add SOFT JEITA hysteresis and jeita configurations ARM: dts: msm: Enable support for secure eud in trinket ARM: dts: msm: Remove Out-of-bound access ARM: dts: msm: enable ESD, ULPS, DFPS and Partial update on sdmmagpie drivers: crypto: Fix compilation errors defconfig: sdxprairie: Enable ION for sdxprairie ARM: dts: msm: update PCIe RX PHY settings for sm8150-v2 mhi: controller: force MHI reset before power up usb: composite: Draw current based on speed upon resume power: qpnp-qg: Update the PON SOC flow ARM: dts: msm: update cpu0 and cpu6 l3 latmon table for magpie target mmc: core: Fix device hangs issue when inserting bad SD cards extcon: Perform device wakeup initialization upon driver probe usb: phy: Add HS PHY tuning parameters to debugfs for SNPS PHY soc: sm8150: Update SC table to reflect version 10.0 changes ARM: dts: msm: Add support for sdmmagpie cpas ARM: dts: msm: set the ST as default panel sdmmagpie defconfig: msm: Add and enable new config for console RX only function drivers: tty: serial: Conditionally disable console write defconfig: msm: Remove various debug configs from perf defconfig ARM: dts: msm: Add rpmsg entry for cdsprm in sdmmagpie input: touchscreen: st: add fix in driver to support VMAP_STACK input: touchscreen: Assign the TP from UEFI or DTSI ARM: dts: msm: Specify max load currents for USB QMP PHY on sm8150 power: smb5: Clean up temperature iio channels ARM: dts: msm: Add SSC QUPV3 I2C device nodes for SM6150 ARM: dts: msm: Update HS PHY parameters for HDK8150 mmc: core: fix SD card request queue refcount underflow during shutdown qcom: hyp_core_ctl: Add a debugfs interface to set reserve CPUs qcom: hyp_core_ctl: Add sysfs interface to read the driver status qcom: hyp_core_ctl: Use hyp system call for vcpu to pcpu assignment qcom: hyp_core_ctl: Add support for thermal management drivers: thermal: cpu_cooling: Add a notifier for max level transitions qcom: hyp_core_ctl: Get reserve CPUs from Hypervisor ARM: dts: msm: support GPU max freq @700Mhz only for v2 usb: phy: qmp: Allow specifying regulator max load from DT usb: phy: qmp: Ensure VDDA regulator is put in HPM usb: dwc3-msm: Fix memory leak of dwc3 child device microvisor: update system headers to version 5.3.6m15 qcom: hyp_core_ctl: Handle CPU offline case after CPU is dead qcom: hyp_core_ctl: Move away from module parameters defconfig: sm8150: Enable Hypervisor core_ctl driver soc: qcom: Add hyp_core_ctl driver clk: qcom: clk-rcg2: Read RCG source before calculating clk rate clk: qcom: Retrieve pre_div from freq_tbl for shared RCG f2fs: remove stale inode entry before eviction from gdirty_list f2fs: fix sbi->extent_list corruption issue power: smb5: Fix initialization error ARM: dts: msm: Add SSC QUPV3 SPI device nodes for SM6150 Coresight: stm: Non-add data header based on diag entity ID ARM: dts: msm: Update GPU chip ID for SM6150 msm: kgsl: Add support for A612 GPU defconfig: Enable sensor clock controller driver for SM6150 ARM: dts: msm: Add QUPV3 SE dt node for i2c on trinket defconfig: sdmsteppe: enable CONFIG_VT mhi: core: allow MHI control driver to set MHI device state mhi: core: put mhi channel, events, and device into a child node ARM: dts: msm: Correct battery profile for SM8150-SDX50M QRD device usb: pd: Notify USB controller every time Rp changes ARM: dts: msm: Add BLSP SE dt node for i2c on sdxprairie ARM: dts: msm: update trinket DT entries for fastRPC usecases msm: kgsl: fix out of bounds register read warnings msm: defconfig: Enable ais kernel driver msm: ais: Add support for multiple slave address ARM: dts: msm: Add secondary phandles for trinket regulators ARM: dts: msm: Fix interrupt type configuration for PM6150 charger ARM: dts: msm: Add the debug clock node for SDXPRAIRIE ARM: dts: msm: Update the GCC/RPMH/AOP clock node for SDXPRAIRIE trace: Fix minor spelling core_ctl trace event power: smb5-lib: update charger switcher frequency for OTG msm: ipa: Add new IOCTL to enable coalescing defconfig: qcs405: Enable ADC configs for 32-bit QCS405 msm: ipa3: Remove state update in wait for completion ARM: dts: msm: Change VAF to 2.9V defconfig: sm8150: Enable USB RNDIS netwrok SW path usb: gadget: Add separate Config option for compiling rndis.c msm: add AIS automotive camera directory ARM: dts: msm: Update squelch detector threshold value for sm8150 ARM: dts: msm: add afe_loopback_tx BE dai for qcs405 msm: camera: Add put_cpu_buf for signaling end of cpu access ARM: dts: msm: Remove LLCC ECC interrupt for SM8150 drivers: edac: Use polling based ECC if there is no ECC IRQ msm: camera: isp: Avoid stop during IFE flush edac: device: Use poll_msec from registered EDAC device msm: camera: isp: Reset last flush req id as part of release msm: camera: Update camera memory table for kernel mapped memory msm: camera: isp: Dump hbi & vbi info incase of dual VFE msm: camera: icp: Reduce delay between subsequent A5 polls msm: camera: isp: Validate packet op-code while checking last flush req soc: qcom: socinfo: Add support for HDK platform msm: camera: crm: Fix use-after-free for link msm: camera: isp: Release HW during shutdown msm: camera: csiphy: Update 8nm csiphy register sequence ARM: dts: msm: add demux node for sdmmagpie msm: camera: isp: avoid changing camif setting in stop msm: camera: isp: Cleanup the start/stop/release functions msm: kgsl: Remove the preemption oob msm: camera: Add stride info as part of pf dump ARM: dts: msm: enable 11AD keep-radio-on-during-sleep on SM8150 defconfig: msm: Enable PCA9956B LED Driver on 32-bit QCS405 ARM: dts: msm: Add correct offset for error irq for sdmmagpie cpas msm: camera: Add support for mapping secure memory for CDSP access ARM: dts: msm: Add Camnoc register map to VFE for sm6150 ARM: dts: msm: Change power-source for cam_reset GPIOs msm: camera: isp: Move event payload to free list in deinit msm: camera: icp: signal error on fences in case of frame process error msm: kgsl: Get names of all fences msm: kgsl: Fix the preemption sysfs node Change-Id: I84cba4dd5da110e20d5123df212d9139ba367282 Signed-off-by:Rohith Palakurthi <prohit@codeaurora.org>
Loading
Please register or sign in to comment