Merge branch 'topic/xilinx' into for-linus

Xilinx AXI VDMA engine, it does transfers between memory and video devices.

It can be configured to have one channel or two channels. If configured

as two channels, one is to transmit to the video device and another is

to receive from the video device.

Required properties:

- compatible: Should be "xlnx,axi-vdma-1.00.a"

- #dma-cells: Should be <1>, see "dmas" property below

- reg: Should contain VDMA registers location and length.

- xlnx,num-fstores: Should be the number of framebuffers as configured in h/w.

- dma-channel child node: Should have at least one channel and can have up to

	two channels per device. This node specifies the properties of each

	DMA channel (see child node properties below).

Optional properties:

- xlnx,include-sg: Tells configured for Scatter-mode in

	the hardware.

- xlnx,flush-fsync: Tells which channel to Flush on Frame sync.

	It takes following values:

	{1}, flush both channels

	{2}, flush mm2s channel

	{3}, flush s2mm channel

Required child node properties:

- compatible: It should be either "xlnx,axi-vdma-mm2s-channel" or

	"xlnx,axi-vdma-s2mm-channel".

- interrupts: Should contain per channel VDMA interrupts.

- xlnx,data-width: Should contain the stream data width, take values

	{32,64...1024}.

Optional child node properties:

- xlnx,include-dre: Tells hardware is configured for Data

	Realignment Engine.

- xlnx,genlock-mode: Tells Genlock synchronization is

	enabled/disabled in hardware.

Example:

++++++++

axi_vdma_0: axivdma@40030000 {

	compatible = "xlnx,axi-vdma-1.00.a";

	#dma_cells = <1>;

	reg = < 0x40030000 0x10000 >;

	xlnx,num-fstores = <0x8>;

	xlnx,flush-fsync = <0x1>;

	dma-channel@40030000 {

		compatible = "xlnx,axi-vdma-mm2s-channel";

		interrupts = < 0 54 4 >;

		xlnx,datawidth = <0x40>;

	} ;

	dma-channel@40030030 {

		compatible = "xlnx,axi-vdma-s2mm-channel";

		interrupts = < 0 53 4 >;

		xlnx,datawidth = <0x40>;

	} ;

} ;

* DMA client

Required properties:

- dmas: a list of <[Video DMA device phandle] [Channel ID]> pairs,

	where Channel ID is '0' for write/tx and '1' for read/rx

	channel.

- dma-names: a list of DMA channel names, one per "dmas" entry

Example:

++++++++

vdmatest_0: vdmatest@0 {

	compatible ="xlnx,axi-vdma-test-1.00.a";

	dmas = <&axi_vdma_0 0

		&axi_vdma_0 1>;

	dma-names = "vdma0", "vdma1";

} ;

	  multiplexing capability for DMA request sources(slot).

	  This module can be found on Freescale Vybrid and LS-1 SoCs.

config XILINX_VDMA

	tristate "Xilinx AXI VDMA Engine"

	depends on (ARCH_ZYNQ || MICROBLAZE)

	select DMA_ENGINE

	help

	  Enable support for Xilinx AXI VDMA Soft IP.

	  This engine provides high-bandwidth direct memory access

	  between memory and AXI4-Stream video type target

	  peripherals including peripherals which support AXI4-

	  Stream Video Protocol.  It has two stream interfaces/

	  channels, Memory Mapped to Stream (MM2S) and Stream to

	  Memory Mapped (S2MM) for the data transfers.

config DMA_ENGINE

	bool

obj-$(CONFIG_MOXART_DMA) += moxart-dma.o

obj-$(CONFIG_FSL_EDMA) += fsl-edma.o

obj-$(CONFIG_QCOM_BAM_DMA) += qcom_bam_dma.o

obj-y += xilinx/

obj-$(CONFIG_XILINX_VDMA) += xilinx_vdma.o