Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next

		is directly the status value from the DMA configuration

		based mailbox before the device is power cycled. Writing

		0 here clears the status.

What:		/sys/bus/thunderbolt/devices/<xdomain>.<service>/key

Date:		Jan 2018

KernelVersion:	4.15

Contact:	thunderbolt-software@lists.01.org

Description:	This contains name of the property directory the XDomain

		service exposes. This entry describes the protocol in

		question. Following directories are already reserved by

		the Apple XDomain specification:

		network:  IP/ethernet over Thunderbolt

		targetdm: Target disk mode protocol over Thunderbolt

		extdisp:  External display mode protocol over Thunderbolt

What:		/sys/bus/thunderbolt/devices/<xdomain>.<service>/modalias

Date:		Jan 2018

KernelVersion:	4.15

Contact:	thunderbolt-software@lists.01.org

Description:	Stores the same MODALIAS value emitted by uevent for

		the XDomain service. Format: tbtsvc:kSpNvNrN

What:		/sys/bus/thunderbolt/devices/<xdomain>.<service>/prtcid

Date:		Jan 2018

KernelVersion:	4.15

Contact:	thunderbolt-software@lists.01.org

Description:	This contains XDomain protocol identifier the XDomain

		service supports.

What:		/sys/bus/thunderbolt/devices/<xdomain>.<service>/prtcvers

Date:		Jan 2018

KernelVersion:	4.15

Contact:	thunderbolt-software@lists.01.org

Description:	This contains XDomain protocol version the XDomain

		service supports.

What:		/sys/bus/thunderbolt/devices/<xdomain>.<service>/prtcrevs

Date:		Jan 2018

KernelVersion:	4.15

Contact:	thunderbolt-software@lists.01.org

Description:	This contains XDomain software version the XDomain

		service supports.

What:		/sys/bus/thunderbolt/devices/<xdomain>.<service>/prtcstns

Date:		Jan 2018

KernelVersion:	4.15

Contact:	thunderbolt-software@lists.01.org

Description:	This contains XDomain service specific settings as

		bitmask. Format: %x

To recover from this mode, one needs to flash a valid NVM image to the

host host controller in the same way it is done in the previous chapter.

Networking over Thunderbolt cable

---------------------------------

Thunderbolt technology allows software communication across two hosts

connected by a Thunderbolt cable.

It is possible to tunnel any kind of traffic over Thunderbolt link but

currently we only support Apple ThunderboltIP protocol.

If the other host is running Windows or macOS only thing you need to

do is to connect Thunderbolt cable between the two hosts, the

``thunderbolt-net`` is loaded automatically. If the other host is also

Linux you should load ``thunderbolt-net`` manually on one host (it does

not matter which one)::

  # modprobe thunderbolt-net

This triggers module load on the other host automatically. If the driver

is built-in to the kernel image, there is no need to do anything.

The driver will create one virtual ethernet interface per Thunderbolt

port which are named like ``thunderbolt0`` and so on. From this point

you can either use standard userspace tools like ``ifconfig`` to

configure the interface or let your GUI to handle it automatically.

BPF extensibility and applicability to networking, tracing, security

in the linux kernel and several user space implementations of BPF

virtual machine led to a number of misunderstanding on what BPF actually is.

This short QA is an attempt to address that and outline a direction

of where BPF is heading long term.

Q: Is BPF a generic instruction set similar to x64 and arm64?

A: NO.

Q: Is BPF a generic virtual machine ?

A: NO.

BPF is generic instruction set _with_ C calling convention.

Q: Why C calling convention was chosen?

A: Because BPF programs are designed to run in the linux kernel

   which is written in C, hence BPF defines instruction set compatible

   with two most used architectures x64 and arm64 (and takes into

   consideration important quirks of other architectures) and

   defines calling convention that is compatible with C calling

   convention of the linux kernel on those architectures.

Q: can multiple return values be supported in the future?

A: NO. BPF allows only register R0 to be used as return value.

Q: can more than 5 function arguments be supported in the future?

A: NO. BPF calling convention only allows registers R1-R5 to be used

   as arguments. BPF is not a standalone instruction set.

   (unlike x64 ISA that allows msft, cdecl and other conventions)

Q: can BPF programs access instruction pointer or return address?

A: NO.

Q: can BPF programs access stack pointer ?

A: NO. Only frame pointer (register R10) is accessible.

   From compiler point of view it's necessary to have stack pointer.

   For example LLVM defines register R11 as stack pointer in its

   BPF backend, but it makes sure that generated code never uses it.

Q: Does C-calling convention diminishes possible use cases?

A: YES. BPF design forces addition of major functionality in the form

   of kernel helper functions and kernel objects like BPF maps with

   seamless interoperability between them. It lets kernel call into

   BPF programs and programs call kernel helpers with zero overhead.

   As all of them were native C code. That is particularly the case

   for JITed BPF programs that are indistinguishable from

   native kernel C code.

Q: Does it mean that 'innovative' extensions to BPF code are disallowed?

A: Soft yes. At least for now until BPF core has support for

   bpf-to-bpf calls, indirect calls, loops, global variables,

   jump tables, read only sections and all other normal constructs

   that C code can produce.

Q: Can loops be supported in a safe way?

A: It's not clear yet. BPF developers are trying to find a way to

   support bounded loops where the verifier can guarantee that

   the program terminates in less than 4096 instructions.

Q: How come LD_ABS and LD_IND instruction are present in BPF whereas

   C code cannot express them and has to use builtin intrinsics?

A: This is artifact of compatibility with classic BPF. Modern

   networking code in BPF performs better without them.

   See 'direct packet access'.

Q: It seems not all BPF instructions are one-to-one to native CPU.

   For example why BPF_JNE and other compare and jumps are not cpu-like?

A: This was necessary to avoid introducing flags into ISA which are

   impossible to make generic and efficient across CPU architectures.

Q: why BPF_DIV instruction doesn't map to x64 div?

A: Because if we picked one-to-one relationship to x64 it would have made

   it more complicated to support on arm64 and other archs. Also it

   needs div-by-zero runtime check.

Q: why there is no BPF_SDIV for signed divide operation?

A: Because it would be rarely used. llvm errors in such case and

   prints a suggestion to use unsigned divide instead

Q: Why BPF has implicit prologue and epilogue?

A: Because architectures like sparc have register windows and in general

   there are enough subtle differences between architectures, so naive

   store return address into stack won't work. Another reason is BPF has

   to be safe from division by zero (and legacy exception path

   of LD_ABS insn). Those instructions need to invoke epilogue and

   return implicitly.

Q: Why BPF_JLT and BPF_JLE instructions were not introduced in the beginning?

A: Because classic BPF didn't have them and BPF authors felt that compiler

   workaround would be acceptable. Turned out that programs lose performance

   due to lack of these compare instructions and they were added.

   These two instructions is a perfect example what kind of new BPF

   instructions are acceptable and can be added in the future.

   These two already had equivalent instructions in native CPUs.

   New instructions that don't have one-to-one mapping to HW instructions

   will not be accepted.

Q: BPF 32-bit subregisters have a requirement to zero upper 32-bits of BPF

   registers which makes BPF inefficient virtual machine for 32-bit

   CPU architectures and 32-bit HW accelerators. Can true 32-bit registers

   be added to BPF in the future?

A: NO. The first thing to improve performance on 32-bit archs is to teach

   LLVM to generate code that uses 32-bit subregisters. Then second step

   is to teach verifier to mark operations where zero-ing upper bits

   is unnecessary. Then JITs can take advantage of those markings and

   drastically reduce size of generated code and improve performance.

Q: Does BPF have a stable ABI?

A: YES. BPF instructions, arguments to BPF programs, set of helper

   functions and their arguments, recognized return codes are all part

   of ABI. However when tracing programs are using bpf_probe_read() helper

   to walk kernel internal datastructures and compile with kernel

   internal headers these accesses can and will break with newer

   kernels. The union bpf_attr -> kern_version is checked at load time

   to prevent accidentally loading kprobe-based bpf programs written

   for a different kernel. Networking programs don't do kern_version check.

Q: How much stack space a BPF program uses?

A: Currently all program types are limited to 512 bytes of stack

   space, but the verifier computes the actual amount of stack used

   and both interpreter and most JITed code consume necessary amount.

Q: Can BPF be offloaded to HW?

A: YES. BPF HW offload is supported by NFP driver.

Q: Does classic BPF interpreter still exist?

A: NO. Classic BPF programs are converted into extend BPF instructions.

Q: Can BPF call arbitrary kernel functions?

A: NO. BPF programs can only call a set of helper functions which

   is defined for every program type.

Q: Can BPF overwrite arbitrary kernel memory?

A: NO. Tracing bpf programs can _read_ arbitrary memory with bpf_probe_read()

   and bpf_probe_read_str() helpers. Networking programs cannot read

   arbitrary memory, since they don't have access to these helpers.

   Programs can never read or write arbitrary memory directly.

Q: Can BPF overwrite arbitrary user memory?

A: Sort-of. Tracing BPF programs can overwrite the user memory

   of the current task with bpf_probe_write_user(). Every time such

   program is loaded the kernel will print warning message, so

   this helper is only useful for experiments and prototypes.

   Tracing BPF programs are root only.

Q: When bpf_trace_printk() helper is used the kernel prints nasty

   warning message. Why is that?

A: This is done to nudge program authors into better interfaces when

   programs need to pass data to user space. Like bpf_perf_event_output()

   can be used to efficiently stream data via perf ring buffer.

   BPF maps can be used for asynchronous data sharing between kernel

   and user space. bpf_trace_printk() should only be used for debugging.

Q: Can BPF functionality such as new program or map types, new

   helpers, etc be added out of kernel module code?

A: NO.

The following properties are common to the Bluetooth controllers:

- local-bd-address: array of 6 bytes, specifies the BD address that was

  uniquely assigned to the Bluetooth device, formatted with least significant

  byte first (little-endian).

			port@1 { /* external port 1 */

				reg = <1>;

				label = "lan1;

				label = "lan1";

			};

			port@2 { /* external port 2 */

					port@1 { /* external port 1 */

						reg = <1>;

						label = "lan1;

						label = "lan1";

					};

					port@2 { /* external port 2 */