Merge "ARM: dts: msm: Add UFS support for sm6150" (23f8a6bc) · Commits · e / devices / android_kernel_oneplus_sm8150

arch/arm64/boot/dts/qcom/sm6150-pinctrl.dtsi

+46 −0

Original line number	Diff line number	Diff line
		@@ -20,6 +20,52 @@
		interrupt-controller;
		#interrupt-cells = <2>;

		ufs_dev_reset_assert: ufs_dev_reset_assert {
		config {
		pins = "ufs_reset";
		bias-pull-down; /* default: pull down */
		/*
		* UFS_RESET driver strengths are having
		* different values/steps compared to typical
		* GPIO drive strengths.
		*
		* Following table clarifies:
		*
		* HDRV value \| UFS_RESET \| Typical GPIO
		* (dec) \| (mA) \| (mA)
		* 0 \| 0.8 \| 2
		* 1 \| 1.55 \| 4
		* 2 \| 2.35 \| 6
		* 3 \| 3.1 \| 8
		* 4 \| 3.9 \| 10
		* 5 \| 4.65 \| 12
		* 6 \| 5.4 \| 14
		* 7 \| 6.15 \| 16
		*
		* POR value for UFS_RESET HDRV is 3 which means
		* 3.1mA and we want to use that. Hence just
		* specify 8mA to "drive-strength" binding and
		* that should result into writing 3 to HDRV
		* field.
		*/
		drive-strength = <8>; /* default: 3.1 mA */
		output-low; /* active low reset */
		};
		};

		ufs_dev_reset_deassert: ufs_dev_reset_deassert {
		config {
		pins = "ufs_reset";
		bias-pull-down; /* default: pull down */
		/*
		* default: 3.1 mA
		* check comments under ufs_dev_reset_assert
		*/
		drive-strength = <8>;
		output-high; /* active low reset */
		};
		};

		/* QUPv3_0 South SE mappings */
		/* SE 0 pin mappings */
		qupv3_se0_2uart_pins: qupv3_se0_2uart_pins {

arch/arm64/boot/dts/qcom/sm6150-rumi.dtsi

+34 −0

Original line number	Diff line number	Diff line
		@@ -72,6 +72,40 @@
		status = "disabled";
		};

		&ufsphy_mem {
		compatible = "qcom,ufs-phy-qrbtc-sdm845";

		vdda-phy-supply = <&pm6150_l4>; /* 0.88v */
		vdda-pll-supply = <&pm6150_l11>; /* 1.2v */
		vdda-phy-max-microamp = <51400>;
		vdda-pll-max-microamp = <14200>;

		status = "ok";
		};

		&ufshc_mem {
		limit-tx-hs-gear = <1>;
		limit-rx-hs-gear = <1>;
		scsi-cmd-timeout = <300000>;

		vdd-hba-supply = <&ufs_phy_gdsc>;
		vdd-hba-fixed-regulator;
		vcc-supply = <&pm6150l_l11>;
		vccq2-supply = <&pm6150_l12>;
		vcc-max-microamp = <600000>;
		vccq2-max-microamp = <600000>;

		qcom,vddp-ref-clk-supply = <&pm6150l_l3>;
		qcom,vddp-ref-clk-max-microamp = <100>;
		qcom,vddp-ref-clk-min-uV = <1232000>;
		qcom,vddp-ref-clk-max-uV = <1260000>;

		qcom,disable-lpm;
		rpm-level = <0>;
		spm-level = <0>;
		status = "ok";
		};

		&spmi_bus {
		status = "disabled";
		};

arch/arm64/boot/dts/qcom/sm6150.dtsi

+73 −0

Original line number	Diff line number	Diff line
		@@ -32,6 +32,7 @@
		interrupt-parent = <&pdc>;

		aliases {
		ufshc1 = &ufshc_mem; /* Embedded UFS slot */
		serial0 = &qupv3_se0_2uart;
		sdhc1 = &sdhc_1; /* SDC1 eMMC slot */
		sdhc2 = &sdhc_2; /* SDC2 SD Card slot */
		@@ -1041,6 +1042,78 @@
		status = "disabled";
		};

		ufsphy_mem: ufsphy_mem@1d87000 {
		reg = <0x1d87000 0xdb8>; /* PHY regs */
		reg-names = "phy_mem";
		#phy-cells = <0>;

		lanes-per-direction = <1>;

		clock-names = "ref_clk_src",
		"ref_clk",
		"ref_aux_clk";
		clocks = <&clock_rpmh RPMH_CXO_CLK>,
		<&clock_gcc GCC_UFS_MEM_CLKREF_CLK>,
		<&clock_gcc GCC_UFS_PHY_PHY_AUX_CLK>;

		status = "disabled";
		};

		ufshc_mem: ufshc@1d84000 {
		compatible = "qcom,ufshc";
		reg = <0x1d84000 0x3000>;
		interrupts = <0 265 0>;
		phys = <&ufsphy_mem>;
		phy-names = "ufsphy";

		lanes-per-direction = <1>;
		dev-ref-clk-freq = <0>; /* 19.2 MHz */
		spm-level = <5>;

		clock-names =
		"core_clk",
		"bus_aggr_clk",
		"iface_clk",
		"core_clk_unipro",
		"core_clk_ice",
		"ref_clk",
		"tx_lane0_sync_clk",
		"rx_lane0_sync_clk";
		clocks =
		<&clock_gcc GCC_UFS_PHY_AXI_CLK>,
		<&clock_gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
		<&clock_gcc GCC_UFS_PHY_AHB_CLK>,
		<&clock_gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
		<&clock_gcc GCC_UFS_PHY_ICE_CORE_CLK>,
		<&clock_rpmh RPMH_CXO_CLK>,
		<&clock_gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
		<&clock_gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>;
		freq-table-hz =
		<37500000 300000000>,
		<0 0>,
		<0 0>,
		<37500000 300000000>,
		<75000000 300000000>,
		<0 0>,
		<0 0>,
		<0 0>;

		/* PM QoS */
		qcom,pm-qos-cpu-groups = <0x3f 0xC0>;
		qcom,pm-qos-cpu-group-latency-us = <67 67>;
		qcom,pm-qos-default-cpu = <0>;

		pinctrl-names = "dev-reset-assert", "dev-reset-deassert";
		pinctrl-0 = <&ufs_dev_reset_assert>;
		pinctrl-1 = <&ufs_dev_reset_deassert>;

		resets = <&clock_gcc GCC_UFS_PHY_BCR>;
		reset-names = "core_reset";
		non-removable;

		status = "disabled";
		};

		spmi_bus: qcom,spmi@c440000 {
		compatible = "qcom,spmi-pmic-arb";
		reg = <0xc440000 0x2300>,