Donate to e Foundation | Murena handsets with /e/OS | Own a part of Murena! Learn more

Commit b203cc7a authored by Mauro Carvalho Chehab's avatar Mauro Carvalho Chehab Committed by Jeff Kirsher
Browse files

networking: e100.rst: Get rid of Sphinx warnings 



Documentation/networking/e100.rst:57: WARNING: Literal block expected; none found.
    Documentation/networking/e100.rst:68: WARNING: Literal block expected; none found.
    Documentation/networking/e100.rst:75: WARNING: Literal block expected; none found.
    Documentation/networking/e100.rst:84: WARNING: Literal block expected; none found.
    Documentation/networking/e100.rst:93: WARNING: Inline emphasis start-string without end-string.

While here, fix some highlights.

Signed-off-by: default avatarMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: default avatarJeff Kirsher <jeffrey.t.kirsher@intel.com>
parent c4111041

Documentation/networking/e100.rst

+17 −10
Original line number Diff line number Diff line
@@ -47,7 +47,8 @@ Driver Configuration Parameters 
The default value for each parameter is generally the recommended setting,

unless otherwise noted.



Rx Descriptors: Number of receive descriptors. A receive descriptor is a data

Rx Descriptors:

   Number of receive descriptors. A receive descriptor is a data

   structure that describes a receive buffer and its attributes to the network

   controller. The data in the descriptor is used by the controller to write

   data from the controller to host memory. In the 3.x.x driver the valid range
@@ -58,7 +59,8 @@ Rx Descriptors: Number of receive descriptors. A receive descriptor is a data 


   Where n is the number of desired Rx descriptors.



Tx Descriptors: Number of transmit descriptors. A transmit descriptor is a data

Tx Descriptors:

   Number of transmit descriptors. A transmit descriptor is a data

   structure that describes a transmit buffer and its attributes to the network

   controller. The data in the descriptor is used by the controller to read

   data from the host memory to the controller. In the 3.x.x driver the valid
@@ -69,7 +71,8 @@ Tx Descriptors: Number of transmit descriptors. A transmit descriptor is a data 


   Where n is the number of desired Tx descriptors.



Speed/Duplex: The driver auto-negotiates the link speed and duplex settings by

Speed/Duplex:

   The driver auto-negotiates the link speed and duplex settings by

   default. The ethtool utility can be used as follows to force speed/duplex.::



     ethtool -s eth?  autoneg off speed {10|100} duplex {full|half}
@@ -77,7 +80,8 @@ Speed/Duplex: The driver auto-negotiates the link speed and duplex settings by 
   NOTE: setting the speed/duplex to incorrect values will cause the link to

   fail.



Event Log Message Level:  The driver uses the message level flag to log events

Event Log Message Level:

   The driver uses the message level flag to log events

   to syslog. The message level can be set at driver load time. It can also be

   set using the command::
@@ -92,7 +96,7 @@ Configuring the Driver on Different Distributions 


Configuring a network driver to load properly when the system is started

is distribution dependent.  Typically, the configuration process involves

adding an alias line to /etc/modprobe.d/*.conf as well as editing other

adding an alias line to `/etc/modprobe.d/*.conf` as well as editing other

system startup scripts and/or configuration files.  Many popular Linux

distributions ship with tools to make these changes for you.  To learn

the proper way to configure a network device for your system, refer to
@@ -160,7 +164,10 @@ This results in unbalanced receive traffic. 
If you have multiple interfaces in a server, either turn on ARP

filtering by



(1) entering:: echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter

(1) entering::



	echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter



    (this only works if your kernel's version is higher than 2.4.5), or



(2) installing the interfaces in separate broadcast domains (either