Merge "ARM: dts: msm: add support for visionox amoled panel" (26f03076) · Commits · e / devices / android_kernel_fairphone_FP4

qcom/dsi-panel-rm69299-visionox-fhd-plus-video.dtsi

0 → 100644

+64 −0

Original line number	Diff line number	Diff line
		&mdss_mdp {
		dsi_rm69299_visionox_amoled_video:
		qcom,mdss_dsi_rm69299_visionox_amoled_video {
		qcom,mdss-dsi-panel-name =
		"rm69299 amoled fhd+ video mode dsi visionox panel";
		qcom,mdss-dsi-panel-type = "dsi_video_mode";
		qcom,dsi-ctrl-num = <0>;
		qcom,dsi-phy-num = <0>;

		qcom,mdss-dsi-virtual-channel-id = <0>;
		qcom,mdss-dsi-stream = <0>;
		qcom,mdss-dsi-bpp = <24>;
		qcom,mdss-dsi-color-order = "rgb_swap_rgb";
		qcom,mdss-dsi-underflow-color = <0xff>;
		qcom,mdss-dsi-border-color = <0>;
		qcom,mdss-dsi-h-sync-pulse = <0>;
		qcom,mdss-dsi-traffic-mode = "non_burst_sync_event";
		qcom,mdss-dsi-lane-map = "lane_map_0123";
		qcom,mdss-dsi-bllp-eof-power-mode;
		qcom,mdss-dsi-bllp-power-mode;
		qcom,mdss-dsi-tx-eot-append;
		qcom,mdss-dsi-lane-0-state;
		qcom,mdss-dsi-lane-1-state;
		qcom,mdss-dsi-lane-2-state;
		qcom,mdss-dsi-lane-3-state;
		qcom,mdss-dsi-dma-trigger = "trigger_sw";
		qcom,mdss-dsi-mdp-trigger = "none";
		qcom,mdss-dsi-lp11-init;
		qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
		qcom,mdss-dsi-reset-sequence = <1 10>, <0 10>, <1 10>;
		qcom,mdss-dsi-te-pin-select = <1>;
		qcom,mdss-dsi-wr-mem-start = <0x2c>;
		qcom,mdss-dsi-wr-mem-continue = <0x3c>;
		qcom,mdss-dsi-te-dcs-command = <1>;
		qcom,mdss-dsi-te-check-enable;
		qcom,mdss-dsi-te-using-te-pin;
		qcom,mdss-dsi-display-timings {
		timing@0 {
		qcom,mdss-dsi-panel-width = <1080>;
		qcom,mdss-dsi-panel-height = <2248>;
		qcom,mdss-dsi-h-front-porch = <26>;
		qcom,mdss-dsi-h-back-porch = <36>;
		qcom,mdss-dsi-h-pulse-width = <2>;
		qcom,mdss-dsi-h-sync-skew = <0>;
		qcom,mdss-dsi-v-back-porch = <4>;
		qcom,mdss-dsi-v-front-porch = <56>;
		qcom,mdss-dsi-v-pulse-width = <4>;
		qcom,mdss-dsi-panel-framerate = <60>;
		qcom,mdss-dsi-on-command = [
		39 01 00 00 00 00 02 FE 00
		39 01 00 00 00 00 02 C2 08
		39 01 00 00 00 00 02 35 00
		39 01 00 00 00 00 02 51 FF
		05 01 00 00 96 00 02 11 00
		05 01 00 00 32 00 02 29 00];
		qcom,mdss-dsi-off-command = [
		05 01 00 00 32 00 02 28 00
		05 01 00 00 96 00 02 10 00];
		qcom,mdss-dsi-on-command-state = "dsi_lp_mode";
		qcom,mdss-dsi-off-command-state = "dsi_hs_mode";
		};
		};
		};
		};

qcom/lito-cdp.dtsi

+10 −0

Original line number	Diff line number	Diff line
		@@ -525,6 +525,16 @@
		qcom,platform-reset-gpio = <&pm8150l_gpios 3 0>;
		qcom,platform-en-gpio = <&pm8150l_gpios 9 0>;
		qcom,platform-bklight-en-gpio = <&pm8150l_gpios 10 0>;

		};

		&dsi_rm69299_visionox_amoled_video {
		qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
		qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
		qcom,mdss-dsi-bl-min-level = <1>;
		qcom,mdss-dsi-bl-max-level = <255>;
		qcom,platform-te-gpio = <&tlmm 10 0>;
		qcom,platform-reset-gpio = <&pm8150l_gpios 3 0>;
		};

		&sde_dsi {

qcom/lito-sde-display.dtsi

+13 −0

Original line number	Diff line number	Diff line
		@@ -18,6 +18,7 @@
		#include "dsi-panel-sim-dualmipi-video.dtsi"
		#include "dsi-panel-sim-dualmipi-dsc375-cmd.dtsi"
		#include "dsi-panel-sim-sec-hd-cmd.dtsi"
		#include "dsi-panel-rm69299-visionox-fhd-plus-video.dtsi"
		#include <dt-bindings/clock/mdss-7nm-pll-clk.h>

		&pm8150l_gpios {
		@@ -196,6 +197,18 @@
		connectors = <&sde_wb &sde_dsi &sde_dsi1 &sde_dp &sde_rscc>;
		};

		&dsi_rm69299_visionox_amoled_video {
		qcom,dsi-select-clocks = "mux_byte_clk0", "mux_pixel_clk0";
		qcom,mdss-dsi-display-timings {
		timing@0 {
		qcom,mdss-dsi-panel-phy-timings = [00 20 08 08 24 23 08
		08 05 02 04 00 1a 18];
		qcom,display-topology = <1 0 1>;
		qcom,default-topology-index = <0>;
		};
		};
		};

		/* PHY TIMINGS REVISION W */
		&dsi_sw43404_amoled_cmd {
		qcom,ulps-enabled;