legacy: Delete bte.h am: 7bc10e79 am: 2796c616

/******************************************************************************

 *

 *  Copyright 2001-2012 Broadcom Corporation

 *

 *  Licensed under the Apache License, Version 2.0 (the "License");

 *  you may not use this file except in compliance with the License.

 *  You may obtain a copy of the License at:

 *

 *  http://www.apache.org/licenses/LICENSE-2.0

 *

 *  Unless required by applicable law or agreed to in writing, software

 *  distributed under the License is distributed on an "AS IS" BASIS,

 *  WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.

 *  See the License for the specific language governing permissions and

 *  limitations under the License.

 *

 ******************************************************************************/

/******************************************************************************

 *

 *  this file contains constants and definitions for the bte project

 *

 ******************************************************************************/

#ifndef BTE_H

#define BTE_H

#include <pthread.h>

#include <semaphore.h>

#include <signal.h>

#include "bt_target.h"

/* By default on shutdown, the baud rate is reset to 115kbits. This should NOT

 * be needed for platforms that kill the BTE driver and remove/reset BT chip.

 */

#ifndef BTE_RESET_BAUD_ON_BT_DISABLE

#define BTE_RESET_BAUD_ON_BT_DISABLE TRUE

#endif

/* Target Modes (based on jumper settings on hardware [see user manual])

 *                           BTE                  BBY

 *                           J3   J4              SW3-3   SW3-2   SW3-1

 *                          --------------------------------------------

 * BTE_MODE_SERIAL_APP,      OUT  OUT             OFF     OFF     OFF

 * BTE_MODE_APPL,            IN   OUT             OFF     OFF     ON

 * BTE_MODE_RESERVED,        OUT  IN              OFF     ON      OFF

 * BTE_MODE_SAMPLE_APPS,     IN   IN              OFF     ON      ON

 * BTE_MODE_DONGLE,          not yet supported    ON      OFF     OFF

 * BTE_MODE_APPL_PROTOCOL_TRACE,     * this is a fake mode *

 * BTE_MODE_INVALID

 */

enum {

  BTE_MODE_SERIAL_APP,          /* Sample serial port application      */

  BTE_MODE_APPL,                /* Target used with Tester through RPC */

  BTE_MODE_RESERVED,            /* Reserved                            */

  BTE_MODE_SAMPLE_APPS,         /* Sample applications (ICP/HSP)       */

  BTE_MODE_DONGLE,              /* Dongle mode                         */

  BTE_MODE_APPL_PROTOCOL_TRACE, /* Allow protocol tracing without rpc */

  BTE_MODE_INVALID

};

extern volatile uint8_t

    bte_target_mode; /* indicates the mode that the board is running in */

/* Startup options */

extern uint32_t bte_startup_options; /* Switch and jumper settings at startup */

void bte_get_startup_options(

    uint32_t*

        p_options); /* Platform specific function for getting startup options */

#define BTE_OPTIONS_TARGET_MODE_MASK                                         \

  0x00000007 /* bits 2-0 indicate target mode (QuickConnect: jp3 & jp4, BBY: \

                SW3-1 & SW3-2)*/

/****************************************************************************

 * Definitions to define which type of application gets built

 ****************************************************************************/

#define BUILD_HCITOOL FALSE

#define BUILD_L2PING FALSE

#define LINUX_FM_DRIVER_INCLUDED FALSE

/* hcisu userial operations. should probably go into bt_types to avoid

 * collisions! */

#define BT_EVT_TO_HCISU_USERIAL_OP (0x0080 | BT_EVT_HCISU)

/* operation for above hcisu event */

#define BT_HCISU_USERIAL_OPEN                                                 \

  (0)                              /* open serial port calling USERIAL_Open() \

                                      */

#define BT_HCISU_USERIAL_CLOSE (1) /* close userial port */

/* options associated with close op */

#define BT_HCISU_USERIAL_CL_NO_DIS_BT \

  0 /* do not touch bt_wake and power gpio */

#define BT_HCISU_USERIAL_CL_DIS_BT                              \

  1 /* put power and bt_wake into defined off state to preserve \

       power */

/* status codes for callback */

#define BTE_HCISU_USERIAL_FAIL 0

#define BTE_HCISU_USERIAL_OK 1

typedef void(tUSERIAL_MSG_CBACK)(int status);

typedef struct tHCISU_USERIAL_MSG_tag {

  BT_HDR_RIGID hdr;

  tUSERIAL_MSG_CBACK* p_cback;

  uint8_t port; /* port number */

  uint8_t op;

  uint8_t option; /* option for operation. depends on operation */

} tHCISU_USERIAL_MSG;

extern void bte_hcisu_userial_oper(tUSERIAL_MSG_CBACK* p_cback, uint8_t port,

                                   uint8_t op, uint8_t option);

/* Pointer to function for sending HCI commands and data to the HCI tranport */

extern int (*p_bte_hci_send)(uint16_t port, BT_HDR* p_msg);

// Initialize control block memory for each stack component.

extern void BTE_InitStack(void);

/* Protocol trace mask */

extern uint32_t bte_proto_trace_mask;

typedef struct tBAUD_REG_tag {

  uint8_t DHBR;

  uint8_t DLBR;

  uint8_t ExplicitBaudRate0;

  uint8_t ExplicitBaudRate1;

  uint8_t ExplicitBaudRate2;

  uint8_t ExplicitBaudRate3;

} tBAUD_REG;

extern const tBAUD_REG baud_rate_regs[];

#endif /* BTE_H */