Remove unused #defs stack/include/hcidefs

#define HCI_GRP_VENDOR_SPECIFIC (0x3F << 10) /* 0xFC00 */

/* Group occupies high 6 bits of the HCI command rest is opcode itself */

#define HCI_OGF(p) (uint8_t)((0xFC00 & (p)) >> 10)

#define HCI_OCF(p) (0x3FF & (p))

/*

 *  Definitions for Link Control Commands

*/

/* Energy info opcode */

#define HCI_BLE_ENERGY_INFO (0x0159 | HCI_GRP_VENDOR_SPECIFIC)

/* Extended BLE Scan parameters opcode */

#define HCI_BLE_EXTENDED_SCAN_PARAMS (0x015A | HCI_GRP_VENDOR_SPECIFIC)

/* Controller debug info opcode */

#define HCI_CONTROLLER_DEBUG_INFO (0x015B | HCI_GRP_VENDOR_SPECIFIC)

/* Bluetooth Quality Report sub event */

#define HCI_VSE_SUBCODE_BQR_SUB_EVT 0x58

/* LE supported states definition */

#define HCI_LE_ADV_STATE 0x00000001

#define HCI_LE_SCAN_STATE 0x00000002

#define HCI_LE_INIT_STATE 0x00000004

#define HCI_LE_CONN_SL_STATE 0x00000008

#define HCI_LE_ADV_SCAN_STATE 0x00000010

#define HCI_LE_ADV_INIT_STATE 0x00000020

#define HCI_LE_ADV_MA_STATE 0x00000040

#define HCI_LE_ADV_SL_STATE 0x00000080

#define HCI_LE_SCAN_INIT_STATE 0x00000100

#define HCI_LE_SCAN_MA_STATE 0x00000200

#define HCI_LE_SCAN_SL_STATE 0x00000400

#define HCI_LE_INIT_MA_STATE 0x00000800

/* LE Supported States */

constexpr uint8_t HCI_LE_STATES_NON_CONN_ADV_BIT = 0;

constexpr uint8_t HCI_LE_STATES_SCAN_ADV_BIT = 1;

#define HCI_KEYPRESS_NOTIFY_EVT 0x3C

#define HCI_RMT_HOST_SUP_FEAT_NOTIFY_EVT 0x3D

/*#define HCI_GENERIC_AMP_LINK_KEY_NOTIF_EVT  0x3E Removed from spec */

#define HCI_PHYSICAL_LINK_COMP_EVT 0x40

#define HCI_CHANNEL_SELECTED_EVT 0x41

#define HCI_DISC_PHYSICAL_LINK_COMP_EVT 0x42

#define HCI_PHY_LINK_LOSS_EARLY_WARNING_EVT 0x43

#define HCI_PHY_LINK_RECOVERY_EVT 0x44

#define HCI_LOGICAL_LINK_COMP_EVT 0x45

#define HCI_DISC_LOGICAL_LINK_COMP_EVT 0x46

#define HCI_FLOW_SPEC_MODIFY_COMP_EVT 0x47

#define HCI_NUM_COMPL_DATA_BLOCKS_EVT 0x48

#define HCI_SHORT_RANGE_MODE_COMPLETE_EVT 0x4C

#define HCI_AMP_STATUS_CHANGE_EVT 0x4D

#define HCI_SET_TRIGGERED_CLOCK_CAPTURE_EVT 0x4E

/* ULP HCI Event */

#define HCI_BLE_EVENT 0x3e

/* ULP Event sub code */

#define HCI_BLE_BIG_SYNC_LOST_EVT 0x1e

#define HCI_BLE_REQ_PEER_SCA_CPL_EVT 0x1f

/* Definitions for LE Channel Map */

#define HCI_BLE_CHNL_MAP_SIZE 5

#define HCI_VENDOR_SPECIFIC_EVT 0xFF /* Vendor specific events */

#define HCI_NAP_TRACE_EVT                       \

  0xFF /* was define 0xFE, 0xFD, change to 0xFF \

          because conflict w/ TCI_EVT and per   \

          specification compliant */

/*

 * Definitions for HCI enable event

*/

#define HCI_INQUIRY_COMPLETE_EV(p) (*((uint32_t*)(p)) & 0x00000001)

#define HCI_INQUIRY_RESULT_EV(p) (*((uint32_t*)(p)) & 0x00000002)

#define HCI_CONNECTION_COMPLETE_EV(p) (*((uint32_t*)(p)) & 0x00000004)

#define HCI_CONNECTION_REQUEST_EV(p) (*((uint32_t*)(p)) & 0x00000008)

#define HCI_PAGE_SCAN_MODE_CHANGED_EV(p) (*((uint32_t*)(p)) & 0x40000000)

#define HCI_PAGE_SCAN_REP_MODE_CHNG_EV(p) (*((uint32_t*)(p)) & 0x80000000)

/* the default event mask for 2.1+EDR (Lisbon) does not include Lisbon events */

#define HCI_DEFAULT_EVENT_MASK_0 0xFFFFFFFF

#define HCI_DEFAULT_EVENT_MASK_1 0x00001FFF

/* the event mask for 2.0 + EDR and later (includes Lisbon events) */

#define HCI_LISBON_EVENT_MASK_0 0xFFFFFFFF

#define HCI_LISBON_EVENT_MASK_1 0x1DBFFFFF

#define HCI_LISBON_EVENT_MASK \

  { 0x0D, 0xBF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF }

#define HCI_LISBON_EVENT_MASK_EXT \

  { 0x1D, 0xBF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF }

#define HCI_DUMO_EVENT_MASK_EXT \

  { 0x3D, 0xBF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF }

/*  0x00001FFF FFFFFFFF Default - no Lisbon events

    0x20000000 00000000 LE Meta Event

 */

/* the event mask for AMP controllers */

#define HCI_AMP_EVENT_MASK_3_0 "\x00\x00\x00\x00\x00\x00\x3F\xFF"

/*  0x0000000000000000 No events specified (default)

    0x0000000000000001 Physical Link Complete Event

    0x0000000000000002 Channel Selected Event

    0x0000000000000004 Disconnection Physical Link Event

    0x0000000000000008 Physical Link Loss Early Warning Event

    0x0000000000000010 Physical Link Recovery Event

    0x0000000000000020 Logical Link Complete Event

    0x0000000000000040 Disconnection Logical Link Complete Event

    0x0000000000000080 Flow Spec Modify Complete Event

    0x0000000000000100 Number of Completed Data Blocks Event

    0x0000000000000200 AMP Start Test Event

    0x0000000000000400 AMP Test End Event

    0x0000000000000800 AMP Receiver Report Event

    0x0000000000001000 Short Range Mode Change Complete Event

    0x0000000000002000 AMP Status Change Event

*/

/* the event mask page 2 (CLB + CSA4) for BR/EDR controller */

#define HCI_PAGE_2_EVENT_MASK "\x00\x00\x00\x00\x00\x7F\xC0\x00"

/*  0x0000000000004000 Triggered Clock Capture Event

    0x0000000000008000 Sync Train Complete Event

    0x0000000000010000 Sync Train Received Event

    0x0000000000020000 Connectionless Broadcast Receive Event

    0x0000000000040000 Connectionless Broadcast Timeout Event

    0x0000000000080000 Truncated Page Complete Event

    0x0000000000100000 Salve Page Response Timeout Event

    0x0000000000200000 Connectionless Broadcast Channel Map Change Event

    0x0000000000400000 Inquiry Response Notification Event

*/

/*

 * Definitions for packet type masks (BT1.2 and BT2.0 definitions)

*/

#define HCI_PKT_TYPES_MASK_DM5 0x4000

#define HCI_PKT_TYPES_MASK_DH5 0x8000

/* Packet type should be one of valid but at least one should be specified */

#define HCI_VALID_SCO_PKT_TYPE(t)                         \

  (((((t) &                                               \

      ~(HCI_PKT_TYPES_MASK_HV1 | HCI_PKT_TYPES_MASK_HV2 | \

        HCI_PKT_TYPES_MASK_HV3)) == 0)) &&                \

   ((t) != 0))

/* Packet type should not be invalid and at least one should be specified */

#define HCI_VALID_ACL_PKT_TYPE(t)                                             \

  (((((t) &                                                                   \

      ~(HCI_PKT_TYPES_MASK_DM1 | HCI_PKT_TYPES_MASK_DH1 |                     \

        HCI_PKT_TYPES_MASK_DM3 | HCI_PKT_TYPES_MASK_DH3 |                     \

        HCI_PKT_TYPES_MASK_DM5 | HCI_PKT_TYPES_MASK_DH5 |                     \

        HCI_PKT_TYPES_MASK_NO_2_DH1 | HCI_PKT_TYPES_MASK_NO_3_DH1 |           \

        HCI_PKT_TYPES_MASK_NO_2_DH3 | HCI_PKT_TYPES_MASK_NO_3_DH3 |           \

        HCI_PKT_TYPES_MASK_NO_2_DH5 | HCI_PKT_TYPES_MASK_NO_3_DH5)) == 0)) && \

   (((t) & (HCI_PKT_TYPES_MASK_DM1 | HCI_PKT_TYPES_MASK_DH1 |                 \

            HCI_PKT_TYPES_MASK_DM3 | HCI_PKT_TYPES_MASK_DH3 |                 \

            HCI_PKT_TYPES_MASK_DM5 | HCI_PKT_TYPES_MASK_DH5)) != 0))

/* Packet type should be one of valid but at least one should be specified for

 * 1.2 */

#define HCI_VALID_ESCO_PKT_TYPE(t)                                           \

  (((((t) &                                                                  \

      ~(HCI_ESCO_PKT_TYPES_MASK_EV3 | HCI_ESCO_PKT_TYPES_MASK_EV4 |          \

        HCI_ESCO_PKT_TYPES_MASK_EV5)) == 0)) &&                              \

   ((t) != 0)) /* Packet type should be one of valid but at least one should \

                  be specified */

#define HCI_VALID_ESCO_SCOPKT_TYPE(t)                           \

  (((((t) &                                                     \

      ~(ESCO_PKT_TYPES_MASK_HV1 | HCI_ESCO_PKT_TYPES_MASK_HV2 | \

        HCI_ESCO_PKT_TYPES_MASK_HV3)) == 0)) &&                 \

   ((t) != 0))

#define HCI_VALID_SCO_ALL_PKT_TYPE(t)                                         \

  (((((t) &                                                                   \

      ~(ESCO_PKT_TYPES_MASK_HV1 | HCI_ESCO_PKT_TYPES_MASK_HV2 |               \

        HCI_ESCO_PKT_TYPES_MASK_HV3 | HCI_ESCO_PKT_TYPES_MASK_EV3 |           \

        HCI_ESCO_PKT_TYPES_MASK_EV4 | HCI_ESCO_PKT_TYPES_MASK_EV5)) == 0)) && \

   ((t) != 0))

/*

 * Define parameters to allow role switch during create connection

*/

#define HCI_CR_CONN_NOT_ALLOW_SWITCH 0x00

#define HCI_CR_CONN_ALLOW_SWITCH 0x01

/*

 * Hold Mode command destination

*/

#define HOLD_MODE_DEST_LOCAL_DEVICE 0x00

#define HOLD_MODE_DEST_RMT_DEVICE 0x01

/*

 *  Definitions for different HCI parameters

*/

#define HCI_PER_INQ_MIN_MAX_PERIOD 0x0003

#define HCI_PER_INQ_MAX_MAX_PERIOD 0xFFFF

#define HCI_PER_INQ_MIN_MIN_PERIOD 0x0002

#define HCI_PER_INQ_MAX_MIN_PERIOD 0xFFFE

#define HCI_MAX_INQUIRY_LENGTH 0x30

#define HCI_MIN_INQ_LAP 0x9E8B00

#define HCI_MAX_INQ_LAP 0x9E8B3F

/* HCI role defenitions */

enum : uint8_t {

  HCI_ROLE_MASTER = 0x00,

#define HCI_MODE_SNIFF 0x02

#define HCI_MODE_PARK 0x03

/* HCI Flow Control Mode defenitions */

#define HCI_PACKET_BASED_FC_MODE 0x00

#define HCI_BLOCK_BASED_FC_MODE 0x01

/* Define Packet types as requested by the Host */

#define HCI_ACL_PKT_TYPE_NONE 0x0000

#define HCI_ACL_PKT_TYPE_DM1 0x0008

#define HCI_ACL_PKT_TYPE_DH1 0x0010

#define HCI_ACL_PKT_TYPE_AUX1 0x0200

#define HCI_ACL_PKT_TYPE_DM3 0x0400

#define HCI_ACL_PKT_TYPE_DH3 0x0800

#define HCI_ACL_PKT_TYPE_DM5 0x4000

#define HCI_ACL_PKT_TYPE_DH5 0x8000

/* Define key type in the Master Link Key command */

#define HCI_USE_SEMI_PERMANENT_KEY 0x00

#define HCI_USE_TEMPORARY_KEY 0x01

/* Page scan period modes */

#define HCI_PAGE_SCAN_REP_MODE_R0 0x00

#define HCI_PAGE_SCAN_REP_MODE_R1 0x01

#define HCI_PAGE_SCAN_REP_MODE_R2 0x02

/* Define limits for page scan repetition modes */

#define HCI_PAGE_SCAN_R1_LIMIT 0x0800

#define HCI_PAGE_SCAN_R2_LIMIT 0x1000

/* Page scan period modes */

#define HCI_PAGE_SCAN_PER_MODE_P0 0x00

#define HCI_PAGE_SCAN_PER_MODE_P1 0x01

#define HCI_PAGE_SCAN_PER_MODE_P2 0x02

/* Page scan modes */

#define HCI_MANDATARY_PAGE_SCAN_MODE 0x00

#define HCI_OPTIONAL_PAGE_SCAN_MODE1 0x01

#define HCI_OPTIONAL_PAGE_SCAN_MODE2 0x02

#define HCI_OPTIONAL_PAGE_SCAN_MODE3 0x03

/* Page and inquiry scan types */

#define HCI_SCAN_TYPE_STANDARD 0x00

#define HCI_SCAN_TYPE_INTERLACED 0x01 /* 1.2 devices or later */

#define HCI_DEF_SCAN_TYPE HCI_SCAN_TYPE_STANDARD

/* Definitions for quality of service service types */

#define HCI_SERVICE_NO_TRAFFIC 0x00

#define HCI_SERVICE_BEST_EFFORT 0x01

#define HCI_SERVICE_GUARANTEED 0x02

#define HCI_QOS_LATENCY_DO_NOT_CARE 0xFFFFFFFF

#define HCI_QOS_DELAY_DO_NOT_CARE 0xFFFFFFFF

/* Definitions for Flow Specification */

#define HCI_FLOW_SPEC_LATENCY_DO_NOT_CARE 0xFFFFFFFF

/* Definitions for AFH Channel Map */

#define HCI_AFH_CHANNEL_MAP_LEN 10

/* Definitions for Extended Inquiry Response */

#define HCI_EXT_INQ_RESPONSE_LEN 240

#define HCI_EIR_FLAGS_TYPE BT_EIR_FLAGS_TYPE

#define HCI_EIR_OOB_SSP_RAND_R_TYPE BT_EIR_OOB_SSP_RAND_R_TYPE

/* Definitions for Write Simple Pairing Mode */

#define HCI_SP_MODE_UNDEFINED 0x00

#define HCI_SP_MODE_ENABLED 0x01

/* Definitions for Write Simple Pairing Debug Mode */

#define HCI_SPD_MODE_DISABLED 0x00

#define HCI_SPD_MODE_ENABLED 0x01

/* Definitions for Write Secure Connections Host Support */

#define HCI_SC_MODE_DISABLED 0x00

#define HCI_SC_MODE_ENABLED 0x01

/* Definitions for IO Capability Response/Command */

#define HCI_IO_CAP_DISPLAY_ONLY 0x00

#define HCI_IO_CAP_DISPLAY_YESNO 0x01

#define HCI_IO_CAP_KEYBOARD_ONLY 0x02

#define HCI_IO_CAP_NO_IO 0x03

#define HCI_OOB_AUTH_DATA_NOT_PRESENT 0x00

#define HCI_OOB_REM_AUTH_DATA_PRESENT 0x01

#define HCI_MITM_PROTECT_NOT_REQUIRED 0x00

#define HCI_MITM_PROTECT_REQUIRED 0x01

/* Policy settings status */

#define HCI_DISABLE_ALL_LM_MODES 0x0000

#define HCI_ENABLE_MASTER_SLAVE_SWITCH 0x0001

#define HCI_ENABLE_SNIFF_MODE 0x0004

#define HCI_ENABLE_PARK_MODE 0x0008

/* By default allow switch, because host can not allow that */

/* that until it created the connection */

#define HCI_DEFAULT_POLICY_SETTINGS HCI_DISABLE_ALL_LM_MODES

/* Filters that are sent in set filter command */

#define HCI_FILTER_TYPE_CLEAR_ALL 0x00

#define HCI_FILTER_INQUIRY_RESULT 0x01

#define HCI_FILTER_CONNECTION_SETUP 0x02

#define HCI_FILTER_COND_NEW_DEVICE 0x00

#define HCI_FILTER_COND_DEVICE_CLASS 0x01

#define HCI_FILTER_COND_BD_ADDR 0x02

#define HCI_DO_NOT_AUTO_ACCEPT_CONNECT 1

/* role switch disabled */

#define HCI_DO_AUTO_ACCEPT_CONNECT 2

/* role switch enabled (1.1 errata 1115) */

#define HCI_DO_AUTO_ACCEPT_CONNECT_RS 3

/* PIN type */

#define HCI_PIN_TYPE_VARIABLE 0

#define HCI_PIN_TYPE_FIXED 1

/* Loopback Modes */

#define HCI_LOOPBACK_MODE_DISABLED 0

#define HCI_LOOPBACK_MODE_LOCAL 1

#define HCI_LOOPBACK_MODE_REMOTE 2

#define SLOTS_PER_10MS 16 /* 0.625 ms slots in a 10 ms tick */

/* Maximum connection accept timeout in 0.625msec */

#define HCI_MAX_CONN_ACCEPT_TOUT 0xB540 /* 29 sec */

#define HCI_DEF_CONN_ACCEPT_TOUT 0x1F40 /* 5 sec */

/* Page timeout is used in LC only and LC is counting down slots not using OS */

#define HCI_DEFAULT_PAGE_TOUT 0x2000 /* 5.12 sec (in slots) */

/* Scan enable flags */

#define HCI_NO_SCAN_ENABLED 0x00

#define HCI_INQUIRY_SCAN_ENABLED 0x01

#define HCI_PAGE_SCAN_ENABLED 0x02

/* Pagescan timer definitions in 0.625 ms */

#define HCI_MIN_PAGESCAN_INTERVAL 0x12   /* 11.25 ms */

#define HCI_MAX_PAGESCAN_INTERVAL 0x1000 /* 2.56 sec */

#define HCI_DEF_PAGESCAN_INTERVAL 0x0800 /* 1.28 sec */

/* Parameter for pagescan window is passed to LC and is kept in slots */

#define HCI_MIN_PAGESCAN_WINDOW 0x11   /* 10.625 ms */

#define HCI_MAX_PAGESCAN_WINDOW 0x1000 /* 2.56  sec */

#define HCI_DEF_PAGESCAN_WINDOW 0x12   /* 11.25 ms  */

/* Inquiryscan timer definitions in 0.625 ms */

#define HCI_MIN_INQUIRYSCAN_INTERVAL 0x12   /* 11.25 ms */

#define HCI_MAX_INQUIRYSCAN_INTERVAL 0x1000 /* 2.56 sec */

#define HCI_DEF_INQUIRYSCAN_INTERVAL 0x1000 /* 2.56 sec */

/* Parameter for inquiryscan window is passed to LC and is kept in slots */

#define HCI_MIN_INQUIRYSCAN_WINDOW 0x11   /* 10.625 ms */

#define HCI_MAX_INQUIRYSCAN_WINDOW 0x1000 /* 2.56 sec */

#define HCI_DEF_INQUIRYSCAN_WINDOW 0x12   /* 11.25 ms */

/* Encryption modes */

#define HCI_ENCRYPT_MODE_DISABLED 0x00

#define HCI_ENCRYPT_MODE_POINT_TO_POINT 0x01

#define HCI_ENCRYPT_MODE_ALL 0x02

/* Voice settings */

#define HCI_INP_CODING_LINEAR 0x0000 /* 0000000000 */

#define HCI_INP_CODING_U_LAW 0x0100  /* 0100000000 */

#define HCI_INP_CODING_A_LAW 0x0200  /* 1000000000 */

#define HCI_INP_CODING_MASK 0x0300   /* 1100000000 */

#define HCI_INP_DATA_FMT_1S_COMPLEMENT 0x0000  /* 0000000000 */

#define HCI_INP_DATA_FMT_2S_COMPLEMENT 0x0040  /* 0001000000 */

#define HCI_INP_DATA_FMT_SIGN_MAGNITUDE 0x0080 /* 0010000000 */

#define HCI_INP_DATA_FMT_UNSIGNED 0x00c0       /* 0011000000 */

#define HCI_INP_DATA_FMT_MASK 0x00c0           /* 0011000000 */

#define HCI_INP_SAMPLE_SIZE_8BIT 0x0000  /* 0000000000 */

#define HCI_INP_SAMPLE_SIZE_16BIT 0x0020 /* 0000100000 */

#define HCI_INP_SAMPLE_SIZE_MASK 0x0020  /* 0000100000 */

#define HCI_INP_LINEAR_PCM_BIT_POS_MASK 0x001c /* 0000011100 */

#define HCI_INP_LINEAR_PCM_BIT_POS_OFFS 2

#define HCI_AIR_CODING_FORMAT_CVSD 0x0000     /* 0000000000 */

  (HCI_INP_CODING_LINEAR | HCI_INP_DATA_FMT_2S_COMPLEMENT | \

   HCI_INP_SAMPLE_SIZE_16BIT | HCI_AIR_CODING_FORMAT_CVSD)

#define HCI_CVSD_SUPPORTED(x) \

  (((x)&HCI_AIR_CODING_FORMAT_MASK) == HCI_AIR_CODING_FORMAT_CVSD)

#define HCI_U_LAW_SUPPORTED(x) \

  (((x)&HCI_AIR_CODING_FORMAT_MASK) == HCI_AIR_CODING_FORMAT_U_LAW)

#define HCI_A_LAW_SUPPORTED(x) \

  (((x)&HCI_AIR_CODING_FORMAT_MASK) == HCI_AIR_CODING_FORMAT_A_LAW)

#define HCI_TRANSPNT_SUPPORTED(x) \

  (((x)&HCI_AIR_CODING_FORMAT_MASK) == HCI_AIR_CODING_FORMAT_TRANSPNT)

/* Retransmit timer definitions in 0.625 */

#define HCI_MAX_AUTOMATIC_FLUSH_TIMEOUT 0x07FF

#define HCI_DEFAULT_AUTOMATIC_FLUSH_TIMEOUT 0 /* No auto flush */

/* Broadcast retransmitions */

#define HCI_DEFAULT_NUM_BCAST_RETRAN 1

/* Define broadcast data types as passed in the hci data packet */

#define HCI_DATA_POINT_TO_POINT 0x00

#define HCI_DATA_ACTIVE_BCAST 0x01

#define HCI_DATA_PICONET_BCAST 0x02

/* Hold mode activity */

#define HCI_MAINTAIN_CUR_POWER_STATE 0x00

#define HCI_SUSPEND_PAGE_SCAN 0x01

#define HCI_SUSPEND_INQUIRY_SCAN 0x02

#define HCI_SUSPEND_PERIODIC_INQUIRIES 0x04

/* Default Link Supervision timeoout */

#define HCI_DEFAULT_INACT_TOUT 0x7D00     /* BR/EDR (20 seconds) */

#define HCI_DEFAULT_AMP_INACT_TOUT 0x3E80 /* AMP    (10 seconds) */

/* Read transmit power level parameter */

#define HCI_READ_CURRENT 0x00

#define HCI_READ_MAXIMUM 0x01

/* Link types for connection complete event */

#define HCI_LINK_TYPE_SCO 0x00

/* Link Key Notification Event (Key Type) definitions */

#define HCI_LKEY_TYPE_COMBINATION 0x00

#define HCI_LKEY_TYPE_LOCAL_UNIT 0x01

#define HCI_LKEY_TYPE_REMOTE_UNIT 0x02

#define HCI_LKEY_TYPE_DEBUG_COMB 0x03

#define HCI_LKEY_TYPE_UNAUTH_COMB 0x04

#define HCI_LKEY_TYPE_UNAUTH_COMB_P_256 0x07

#define HCI_LKEY_TYPE_AUTH_COMB_P_256 0x08

/* Read Local Version HCI Version return values (Command Complete Event) */

#define HCI_VERSION_1_0B 0x00

#define HCI_VERSION_1_1 0x01

/* Define an invalid value for a handle */

#define HCI_INVALID_HANDLE 0xFFFF

/* Define max ammount of data in the HCI command */

#define HCI_COMMAND_SIZE 255

/* Define the preamble length for all HCI Commands.

 * This is 2-bytes for opcode and 1 byte for length

*/

/* local Bluetooth controller id for AMP HCI */

#define LOCAL_BR_EDR_CONTROLLER_ID 0

/* controller id types for AMP HCI */

#define HCI_CONTROLLER_TYPE_BR_EDR 0

#define HCI_CONTROLLER_TYPE_802_11 1

#define HCI_CONTROLLER_TYPE_ECMA 2

#define HCI_MAX_CONTROLLER_TYPES 3

/*  ConnectionLess Broadcast */

#define HCI_CLB_DISABLE 0x00

#define HCI_CLB_ENABLE 0x01

/* ConnectionLess Broadcast Data fragment */

#define HCI_CLB_FRAGMENT_CONT 0x00

#define HCI_CLB_FRAGMENT_START 0x01

#define HCI_CLB_FRAGMENT_END 0x02

#define HCI_CLB_FRAGMENT_SINGLE 0x03

/* AMP Controller Status codes

*/

#define HCI_AMP_CTRLR_PHYSICALLY_DOWN 0

#define HCI_AMP_CTRLR_USABLE_BY_BT 1

#define HCI_AMP_CTRLR_UNUSABLE_FOR_BT 2

#define HCI_AMP_CTRLR_LOW_CAP_FOR_BT 3

#define HCI_AMP_CTRLR_MED_CAP_FOR_BT 4

#define HCI_AMP_CTRLR_HIGH_CAP_FOR_BT 5

#define HCI_AMP_CTRLR_FULL_CAP_FOR_BT 6

#define HCI_MAX_AMP_STATUS_TYPES 7

/* Define the extended flow specification fields used by AMP */

typedef struct {

  uint8_t id;

  uint32_t flush_timeout;

} tHCI_EXT_FLOW_SPEC;

/* HCI message type definitions (for H4 messages) */

#define HCIT_TYPE_COMMAND 1

#define HCIT_TYPE_ACL_DATA 2

#define HCIT_TYPE_SCO_DATA 3

#define HCIT_TYPE_EVENT 4

#define HCIT_TYPE_LM_DIAG 7

#define HCIT_TYPE_NFC 16

#define HCIT_LM_DIAG_LENGTH 63

/* Parameter information for HCI_BRCM_SET_ACL_PRIORITY */

#define HCI_BRCM_ACL_PRIORITY_PARAM_SIZE 3

#define HCI_BRCM_ACL_PRIORITY_LOW 0x00

#define HCI_BRCM_ACL_PRIORITY_HIGH 0xFF

#define HCI_BRCM_SET_ACL_PRIORITY (0x0057 | HCI_GRP_VENDOR_SPECIFIC)

/* Define values for LMP Test Control parameters

 * Test Scenario, Hopping Mode, Power Control Mode

*/

#define LMP_TESTCTL_TESTSC_PAUSE 0

#define LMP_TESTCTL_TESTSC_TXTEST_0 1

#define LMP_TESTCTL_TESTSC_TXTEST_1 2

#define LMP_TESTCTL_TESTSC_TXTEST_1010 3

#define LMP_TESTCTL_TESTSC_PSRND_BITSEQ 4

#define LMP_TESTCTL_TESTSC_CLOSEDLB_ACL 5

#define LMP_TESTCTL_TESTSC_CLOSEDLB_SCO 6

#define LMP_TESTCTL_TESTSC_ACL_NOWHIT 7

#define LMP_TESTCTL_TESTSC_SCO_NOWHIT 8

#define LMP_TESTCTL_TESTSC_TXTEST_11110000 9

#define LMP_TESTCTL_TESTSC_EXITTESTMODE 255

#define LMP_TESTCTL_HOPMOD_RXTX1FREQ 0

#define LMP_TESTCTL_HOPMOD_HOP_EURUSA 1

#define LMP_TESTCTL_HOPMOD_HOP_JAPAN 2

#define LMP_TESTCTL_HOPMOD_HOP_FRANCE 3

#define LMP_TESTCTL_HOPMOD_HOP_SPAIN 4

#define LMP_TESTCTL_HOPMOD_REDUCED_HOP 5

#define LMP_TESTCTL_POWCTL_FIXEDTX_OP 0

#define LMP_TESTCTL_POWCTL_ADAPTIVE 1

#define LMP_COMPID_GOOGLE 0xE0

// TODO(zachoverflow): remove this once broadcom specific hacks are removed

#define LMP_COMPID_BROADCOM 15

/*

 * Define the packet types in the packet header, and a couple extra

*/

#define PKT_TYPE_NULL 0x00

#define PKT_TYPE_POLL 0x01

#define PKT_TYPE_FHS 0x02

#define PKT_TYPE_DM1 0x03

#define PKT_TYPE_DH1 0x04

#define PKT_TYPE_HV1 0x05

#define PKT_TYPE_HV2 0x06

#define PKT_TYPE_HV3 0x07

#define PKT_TYPE_DV 0x08

#define PKT_TYPE_AUX1 0x09

#define PKT_TYPE_DM3 0x0a

#define PKT_TYPE_DH3 0x0b

#define PKT_TYPE_DM5 0x0e

#define PKT_TYPE_DH5 0x0f

#define PKT_TYPE_ID 0x10 /* Internally used packet types */

#define PKT_TYPE_BAD 0x11

#define PKT_TYPE_NONE 0x12

/*

 * Define packet size

*/

#define HCI_EXT_FEATURES_SUCCESS_EVT_LEN 13

#define HCI_FEATURES_KNOWN(x) \

  (((x)[0] | (x)[1] | (x)[2] | (x)[3] | (x)[4] | (x)[5] | (x)[6] | (x)[7]) != 0)

/* LMP features encoding - page 0 */

#define HCI_3_SLOT_PACKETS_SUPPORTED(x) ((x)[0] & 0x01)

#define HCI_5_SLOT_PACKETS_SUPPORTED(x) ((x)[0] & 0x02)