Copy ISensors 1.0 into 2.0 directory (ee3f7201) · Commits · e / os / android_hardware_interfaces

sensors/2.0/Android.bp

0 → 100644

+18 −0

Original line number	Diff line number	Diff line
		// This file is autogenerated by hidl-gen -Landroidbp.

		hidl_interface {
		name: "android.hardware.sensors@2.0",
		root: "android.hardware",
		vndk: {
		enabled: true,
		},
		srcs: [
		"ISensors.hal",
		],
		interfaces: [
		"android.hardware.sensors@1.0",
		"android.hidl.base@1.0",
		],
		gen_java: false,
		}

sensors/2.0/ISensors.hal

0 → 100644

+203 −0

Original line number	Diff line number	Diff line
		/*
		* Copyright (C) 2018 The Android Open Source Project
		*
		* Licensed under the Apache License, Version 2.0 (the "License");
		* you may not use this file except in compliance with the License.
		* You may obtain a copy of the License at
		*
		* http://www.apache.org/licenses/LICENSE-2.0
		*
		* Unless required by applicable law or agreed to in writing, software
		* distributed under the License is distributed on an "AS IS" BASIS,
		* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
		* See the License for the specific language governing permissions and
		* limitations under the License.
		*/

		package android.hardware.sensors@2.0;

		import @1.0::Event;
		import @1.0::OperationMode;
		import @1.0::RateLevel;
		import @1.0::Result;
		import @1.0::SensorInfo;
		import @1.0::SharedMemInfo;

		interface ISensors {
		/**
		* Enumerate all available (static) sensors.
		*/
		getSensorsList() generates (vec<SensorInfo> list);

		/**
		* Place the module in a specific mode. The following modes are defined
		*
		* SENSOR_HAL_NORMAL_MODE - Normal operation. Default state of the module.
		*
		* SENSOR_HAL_DATA_INJECTION_MODE - Loopback mode.
		* Data is injected for the supported sensors by the sensor service in
		* this mode.
		*
		* @return OK on success
		* BAD_VALUE if requested mode is not supported
		* PERMISSION_DENIED if operation is not allowed
		*/
		setOperationMode(OperationMode mode) generates (Result result);

		/**
		* Activate/de-activate one sensor.
		*
		* After sensor de-activation, existing sensor events that have not
		* been picked up by poll() must be abandoned immediately so that
		* subsequent activations do not get stale sensor events (events
		* that are generated prior to the latter activation).
		*
		* @param sensorHandle is the handle of the sensor to change.
		* @param enabled set to true to enable, or false to disable the sensor.
		* @return result OK on success, BAD_VALUE if sensorHandle is invalid.
		*/
		activate(int32_t sensorHandle, bool enabled) generates (Result result);

		/**
		* Generate a vector of sensor events containing at most "maxCount"
		* entries.
		*
		* Additionally a vector of SensorInfos is returned for any dynamic sensors
		* connected as notified by returned events of type DYNAMIC_SENSOR_META.
		*
		* If there is no sensor event when this function is being called, block
		* until there are sensor events available.
		*
		* @param maxCount max number of samples can be returned, must be > 0.
		* Actual number of events returned in data must be <= maxCount and > 0
		* @return result OK on success or BAD_VALUE if maxCount <= 0.
		* @return data vector of Event contains sensor events.
		* @return dynamicSensorsAdded vector of SensorInfo contains dynamic sensor
		* added. Each element corresponds to a dynamic sensor meta events in
		* data.
		*/
		poll(int32_t maxCount)
		generates (
		Result result,
		vec<Event> data,
		vec<SensorInfo> dynamicSensorsAdded);

		/**
		* Sets a sensor’s parameters, including sampling frequency and maximum
		* report latency. This function can be called while the sensor is
		* activated, in which case it must not cause any sensor measurements to
		* be lost: transitioning from one sampling rate to the other cannot cause
		* lost events, nor can transitioning from a high maximum report latency to
		* a low maximum report latency.
		*
		* @param sensorHandle handle of sensor to be changed.
		* @param samplingPeriodNs specifies sensor sample period in nanoseconds.
		* @param maxReportLatencyNs allowed delay time before an event is sampled
		* to time of report.
		* @return result OK on success, BAD_VALUE if any parameters are invalid.
		*/
		batch(int32_t sensorHandle,
		int64_t samplingPeriodNs,
		int64_t maxReportLatencyNs)
		generates (
		Result result);

		/**
		* Trigger a flush of internal FIFO.
		*
		* Flush adds a FLUSH_COMPLETE metadata event to the end of the "batch mode"
		* FIFO for the specified sensor and flushes the FIFO. If the FIFO is empty
		* or if the sensor doesn't support batching (FIFO size zero), return
		* SUCCESS and add a trivial FLUSH_COMPLETE event added to the event stream.
		* This applies to all sensors other than one-shot sensors. If the sensor
		* is a one-shot sensor, flush must return BAD_VALUE and not generate any
		* flush complete metadata. If the sensor is not active at the time flush()
		* is called, flush() return BAD_VALUE.
		*
		* @param sensorHandle handle of sensor to be flushed.
		* @return result OK on success and BAD_VALUE if sensorHandle is invalid.
		*/
		flush(int32_t sensorHandle) generates (Result result);

		/**
		* Inject a single sensor event or push operation environment parameters to
		* device.
		*
		* When device is in NORMAL mode, this function is called to push operation
		* environment data to device. In this operation, Event is always of
		* SensorType::AdditionalInfo type. See operation evironment parameters
		* section in AdditionalInfoType.
		*
		* When device is in DATA_INJECTION mode, this function is also used for
		* injecting sensor events.
		*
		* Regardless of OperationMode, injected SensorType::ADDITIONAL_INFO
		* type events should not be routed back to poll() function.
		*
		* @see AdditionalInfoType
		* @see OperationMode
		* @param event sensor event to be injected
		* @return result OK on success; PERMISSION_DENIED if operation is not
		* allowed; INVALID_OPERATION, if this functionality is unsupported;
		* BAD_VALUE if sensor event cannot be injected.
		*/
		injectSensorData(Event event) generates (Result result);

		/**
		* Register direct report channel.
		*
		* Register a direct channel with supplied shared memory information. Upon
		* return, the sensor hardware is responsible for resetting the memory
		* content to initial value (depending on memory format settings).
		*
		* @param mem shared memory info data structure.
		* @return result OK on success; BAD_VALUE if shared memory information is
		* not consistent; NO_MEMORY if shared memory cannot be used by sensor
		* system; INVALID_OPERATION if functionality is not supported.
		* @return channelHandle a positive integer used for referencing registered
		* direct channel (>0) in configureDirectReport and
		* unregisterDirectChannel if result is OK, -1 otherwise.
		*/
		registerDirectChannel(SharedMemInfo mem)
		generates (Result result,
		int32_t channelHandle);

		/**
		* Unregister direct report channel.
		*
		* Unregister a direct channel previously registered using
		* registerDirectChannel, and remove all active sensor report configured in
		* still active sensor report configured in the direct channel.
		*
		* @param channelHandle handle of direct channel to be unregistered.
		* @return result OK if direct report is supported; INVALID_OPERATION
		* otherwise.
		*/
		unregisterDirectChannel(int32_t channelHandle) generates (Result result);

		/**
		* Configure direct sensor event report in direct channel.
		*
		* This function start, modify rate or stop direct report of a sensor in a
		* certain direct channel.
		*
		* @param sensorHandle handle of sensor to be configured. When combined
		* with STOP rate, sensorHandle can be -1 to denote all active sensors
		* in the direct channel specified by channel Handle.
		* @param channelHandle handle of direct channel to be configured.
		* @param rate rate level, see RateLevel enum.
		* @return result OK on success; BAD_VALUE if parameter is invalid (such as
		* rate level is not supported by sensor, channelHandle does not exist,
		* etc); INVALID_OPERATION if functionality is not supported.
		* @return reportToken positive integer to identify multiple sensors of
		* the same type in a single direct channel. Ignored if rate is STOP.
		* See SharedMemFormat.
		*/
		configDirectReport(
		int32_t sensorHandle,
		int32_t channelHandle,
		RateLevel rate
		) generates (
		Result result,
		int32_t reportToken);
		};