Donate to e Foundation | Murena handsets with /e/OS | Own a part of Murena! Learn more

Commit fe6253da authored by Ramendra Kumar's avatar Ramendra Kumar Committed by Gerrit - the friendly Code Review server
Browse files

ARM: dts: msm: add display related dt nodes on QCS410 device 



Add DSI and bridge chip dt nodes on QCS410 device.

Change-Id: I55665cb93ec0f462da7abb696b300450d4067fc7
Signed-off-by: default avatarRamendra Kumar <ramendra@codeaurora.org>
parent 0151f537

arch/arm64/boot/dts/qcom/qcs410-iot.dtsi

+128 −1
Original line number Diff line number Diff line
@@ -19,7 +19,9 @@ 
#include <dt-bindings/clock/qcom,cpucc-sm8150.h>

#include <dt-bindings/clock/qcom,dispcc-sm6150.h>

#include <dt-bindings/clock/qcom,gpucc-sm6150.h>



#include "qcs410.dtsi"

#include "sm6150-sde-pll.dtsi"

#include "sm6150-sde-display.dtsi"

#include "qcs610-camera-sensor-idp.dtsi"



/ {
@@ -32,6 +34,10 @@ 
	#include "smb1390.dtsi"

};



&fsa4480 {

	status = "disabled";

};



&pm6150l_gpios {

	key_vol_up {

		key_vol_up_default: key_vol_up_default {
@@ -235,3 +241,124 @@ 
&L5C {

	regulator-max-microvolt = <2912000>;

};



&sde_dp {

	status="disabled";

};



&mdss_dp_pll {

	status="disabled";

};



&mdss_mdp {

	connectors = <&sde_rscc &sde_wb &sde_dsi>;

};



&qupv3_se1_i2c {

	status = "ok";

	lt9611: lt,lt9611@3b {

		compatible = "lt,lt9611";

		reg = <0x3b>;

		interrupt-parent = <&tlmm>;

		interrupts = <26 0>;

		interrupt-names = "lt_irq";

		lt,irq-gpio = <&tlmm 26 0x0>;

		lt,reset-gpio = <&tlmm 20 0x0>;

		lt,hdmi-en-gpio = <&tlmm 79 0x0>;

		instance_id = <0>;

		lt,non-pluggable;

		lt,preferred-mode = "1920x1080";



		pinctrl-names = "default";

		pinctrl-0 = <&lt9611_pins>;



		vdd-supply = <&pm6150_l13>;

		vcc-supply = <&pm6150_l16>;



		lt,supply-entries {

			#address-cells = <1>;

			#size-cells = <0>;



			lt,supply-entry@0 {

				reg = <0>;

				lt,supply-name = "vdd";

				lt,supply-min-voltage = <1800000>;

				lt,supply-max-voltage = <1800000>;

				lt,supply-enable-load = <200000>;

				lt,supply-post-on-sleep = <50>;

			};

			lt,supply-entry@1 {

				reg = <1>;

				lt,supply-name = "vcc";

				lt,supply-min-voltage = <3304000>;

				lt,supply-max-voltage = <3304000>;

				lt,supply-enable-load = <200000>;

				lt,supply-post-on-sleep = <50>;

			};





		};



		lt,customize-modes {

			lt,customize-mode-id@0 {

				lt,mode-h-active = <1920>;

				lt,mode-h-front-porch = <88>;

				lt,mode-h-pulse-width = <44>;

				lt,mode-h-back-porch = <148>;

				lt,mode-h-active-high;

				lt,mode-v-active = <1080>;

				lt,mode-v-front-porch = <4>;

				lt,mode-v-pulse-width = <5>;

				lt,mode-v-back-porch = <36>;

				lt,mode-v-active-high;

				lt,mode-refresh-rate = <60>;

				lt,mode-clock-in-khz = <148500>;

			};

		};



		ports {

			#address-cells = <1>;

			#size-cells = <0>;



			port@0 {

				reg = <0>;

				lt9611_in: endpoint {

					remote-endpoint = <&ext_dsi_out>;

				};

			};

		};

	};

};



&dsi_ext_bridge_hdmi_1080p {

	qcom,mdss-dsi-ext-bridge = <0>;

};



&soc {

	ext_dsi_bridge_display: qcom,dsi-display@50 {

		label = "ext_dsi_bridge_display hdmi 1080p";

		qcom,dsi-display-active;

		qcom,display-type = "primary";



		qcom,dsi-ctrl-num = <0>;

		qcom,dsi-phy-num = <0>;

		qcom,dsi-select-clocks = "mux_byte_clk0", "mux_pixel_clk0";

		qcom,dsi-panel = <&dsi_ext_bridge_hdmi_1080p>;

	};

};



&sde_dsi {

	qcom,dsi-display-list = <&ext_dsi_bridge_display>;



	ports {

		#address-cells = <1>;

		#size-cells = <0>;



		port@0 {

			reg = <0>;

			ext_dsi_out: endpoint {

				remote-endpoint = <&lt9611_in>;

			};

		};

	};

};