Merge remote-tracking branches 'regulator/topic/fan53555',... (ce59dedf) · Commits · e / devices / android_kernel_xiaomi_nabu

Documentation/devicetree/bindings/regulator/regulator-max77620.txt

+22 −0

Original line number	Diff line number	Diff line
		@@ -94,6 +94,28 @@ Following are additional properties:
		This is applicable if suspend state
		FPS source is selected as FPS0, FPS1 or
		FPS2.
		- maxim,ramp-rate-setting: integer, ramp rate(uV/us) setting to be
		configured to the device.
		The platform may have different ramp
		rate than advertised ramp rate if it has
		design variation from Maxim's
		recommended. On this case, platform
		specific ramp rate is used for ramp time
		calculation and this property is used
		for device register configurations.
		The measured ramp rate of platform is
		provided by the regulator-ramp-delay
		as described in <devicetree/bindings/
		regulator/regulator.txt>.
		Maxim Max77620 supports following ramp
		delay:
		SD: 13.75mV/us, 27.5mV/us, 55mV/us
		LDOs: 5mV/us, 100mV/us

		Note: If the measured ramp delay is same as advertised ramp delay then it is not
		required to provide the ramp delay with property "maxim,ramp-rate-setting". The
		ramp rate can be provided by the regulator-ramp-delay which will be used for
		ramp time calculation for voltage change as well as for device configuration.

		Example:
		--------

+9 −0

Original line number	Diff line number	Diff line
		@@ -321,6 +321,15 @@ config REGULATOR_LP872X
		help
		This driver supports LP8720/LP8725 PMIC

		config REGULATOR_LP873X
		tristate "TI LP873X Power regulators"
		depends on MFD_LP873X && OF
		help
		This driver supports LP873X voltage regulator chips. LP873X
		provides two step-down converters and two general-purpose LDO
		voltage regulators. It supports software based voltage control
		for different voltage domains

		config REGULATOR_LP8755
		tristate "TI LP8755 High Performance PMU driver"
		depends on I2C

+1 −0

Original line number	Diff line number	Diff line
		@@ -42,6 +42,7 @@ obj-$(CONFIG_REGULATOR_LM363X) += lm363x-regulator.o
		obj-$(CONFIG_REGULATOR_LP3971) += lp3971.o
		obj-$(CONFIG_REGULATOR_LP3972) += lp3972.o
		obj-$(CONFIG_REGULATOR_LP872X) += lp872x.o
		obj-$(CONFIG_REGULATOR_LP873X) += lp873x-regulator.o
		obj-$(CONFIG_REGULATOR_LP8788) += lp8788-buck.o
		obj-$(CONFIG_REGULATOR_LP8788) += lp8788-ldo.o
		obj-$(CONFIG_REGULATOR_LP8755) += lp8755.o

+24 −0

Original line number	Diff line number	Diff line
		@@ -65,6 +65,13 @@ enum {
		FAN53555_CHIP_ID_03,
		FAN53555_CHIP_ID_04,
		FAN53555_CHIP_ID_05,
		FAN53555_CHIP_ID_08 = 8,
		};

		/* IC mask revision */
		enum {
		FAN53555_CHIP_REV_00 = 0x3,
		FAN53555_CHIP_REV_13 = 0xf,
		};

		enum {
		@@ -217,9 +224,26 @@ static int fan53555_voltages_setup_fairchild(struct fan53555_device_info *di)
		/* Init voltage range and step */
		switch (di->chip_id) {
		case FAN53555_CHIP_ID_00:
		switch (di->chip_rev) {
		case FAN53555_CHIP_REV_00:
		di->vsel_min = 600000;
		di->vsel_step = 10000;
		break;
		case FAN53555_CHIP_REV_13:
		di->vsel_min = 800000;
		di->vsel_step = 10000;
		break;
		default:
		dev_err(di->dev,
		"Chip ID %d with rev %d not supported!\n",
		di->chip_id, di->chip_rev);
		return -EINVAL;
		}
		break;
		case FAN53555_CHIP_ID_01:
		case FAN53555_CHIP_ID_03:
		case FAN53555_CHIP_ID_05:
		case FAN53555_CHIP_ID_08:
		di->vsel_min = 600000;
		di->vsel_step = 10000;
		break;

+1 −1

Original line number	Diff line number	Diff line
		@@ -365,8 +365,8 @@ static int lp3971_set_bits(struct lp3971 *lp3971, u8 reg, u16 mask, u16 val)
		mutex_lock(&lp3971->io_lock);

		ret = lp3971_i2c_read(lp3971->i2c, reg, 1, &tmp);
		tmp = (tmp & ~mask) \| val;
		if (ret == 0) {
		tmp = (tmp & ~mask) \| val;
		ret = lp3971_i2c_write(lp3971->i2c, reg, 1, &tmp);
		dev_dbg(lp3971->dev, "reg write 0x%02x -> 0x%02x\n", (int)reg,
		(unsigned)val&0xff);