Merge "regulator: rpm-smd-regulator: Add snapshot of rpm-smd-regulator driver"

Qualcomm RPM Regulators

rpm-regulator-smd is a regulator driver which supports regulators inside of

PMICs which are controlled by the RPM processor.  Communication with the RPM

processor takes place over SMD.

Required structure:

- RPM regulators must be described in two levels of devices nodes.  The first

	level describes the interface with the RPM.  The second level describes

	properties of one regulator framework interface (of potentially many) to

	the regulator.

[First Level Nodes]

Required properties:

- compatible:          Must be "qcom,rpm-smd-regulator-resource"

- qcom,resource-name:  Resource name string for this regulator to be used in RPM

			transactions.  Length is 4 characters max.

- qcom,resource-id:    Resource instance ID for this regulator to be used in RPM

			transactions.

- qcom,regulator-type: Type of this regulator.  Supported values are:

				0 = LDO

				1 = SMPS

				2 = VS

				3 = NCP

				4 = Buck or Boost (BoB)

Optional properties:

- qcom,allow-atomic:   Flag specifying if atomic access is allowed for this

			regulator.  Supported values are:

				0 or not present = mutex locks used

				1 = spinlocks used

- qcom,enable-time:    Time in us to delay after enabling the regulator

- qcom,hpm-min-load:   Load current in uA which corresponds to the minimum load

			which requires the regulator to be in high power mode.

- qcom,apps-only:      Flag which indicates that the regulator only has

			consumers on the application processor. If this flag

			is specified, then voltage and current updates are

			only sent to the RPM if the regulator is enabled.

- qcom,always-wait-for-ack:   Flag which indicates that the application

			processor must wait for an ACK or a NACK from the RPM

			for every request sent for this regulator including

			those which are for a strictly lower power state.

[Second Level Nodes]

Required properties:

- compatible:          Must be "qcom,rpm-smd-regulator"

- regulator-name:      A string used as a descriptive name for regulator outputs

- qcom,set:            Specifies which sets that requests made with this

			regulator interface should be sent to.  Regulator

			requests sent in the active set take effect immediately.

			Requests sent in the sleep set take effect when the Apps

			processor transitions into RPM assisted power collapse.

			Supported values are:

				1 = Active set only

				2 = Sleep set only

				3 = Both active and sleep sets

Optional properties:

- parent-supply:               phandle to the parent supply/regulator node

- qcom,system-load:            Load in uA present on regulator that is not

				captured by any consumer request

- qcom,use-voltage-corner:     Flag that signifies if regulator_set_voltage

				calls should modify the corner parameter instead

				of the voltage parameter.  When used, voltages

				specified inside of the regulator framework

				represent corners that have been incremented by

				1.  This value shift is necessary to work around

				limitations in the regulator framework which

				treat 0 uV as an error.

- qcom,use-voltage-floor-corner:  Flag that signifies if regulator_set_voltage

				calls should modify the floor corner parameter

				instead of the voltage parameter.  When used,

				voltages specified inside of the regulator

				framework represent corners that have been

				incremented by 1.  The properties

				qcom,use-voltage-corner and

				qcom,use-voltage-floor-corner are mutually

				exclusive.  Only one may be specified for a

				given regulator.

- qcom,use-voltage-level:      Flag that signifies if regulator_set_voltage

				calls should modify the level parameter instead

				of the voltage parameter.

- qcom,use-voltage-floor-level:   Flag that signifies if regulator_set_voltage

				calls should modify the floor level parameter

				instead of the voltage parameter.

				The properties qcom,use-voltage-level and

				qcom,use-voltage-floor-level are mutually

				exclusive.  Only one may be specified for a

				given regulator.

- qcom,use-pin-ctrl-voltage1:  Flag which indicates that updates to voltage

				should be sent to the pin control voltage 1

				parameter. Only one pin may be specified per

				regulator. This property only applies to BoB

				type regulators.

- qcom,use-pin-ctrl-voltage2:  Flag which indicates that updates to voltage

				should be sent to the pin control voltage 2

				parameter. Only one pin may be specified per

				regulator. This property only applies to BoB

				type regulators.

- qcom,use-pin-ctrl-voltage3:  Flag which indicates that updates to voltage

				should be sent to the pin control voltage 3

				parameter. Only one pin may be specified per

				regulator. This property only applies to BoB

				type regulators.

- qcom,always-send-voltage:    Flag which indicates that updates to the

				voltage, voltage corner or voltage level set

				point should always be sent immediately to the

				RPM. If this flag is not specified, then

				voltage set point updates are only sent if the

				given regulator has also been enabled by a

				Linux consumer.

- qcom,always-send-current:    Flag which indicates that updates to the load

				current should always be sent immediately to the

				RPM.  If this flag is not specified, then load

				current updates are only sent if the given

				regulator has also been enabled by a Linux

				consumer.

- qcom,send-defaults:          Boolean flag which indicates that the initial

				parameter values should be sent to the RPM

				before consumers make their own requests.  If

				this flag is not specified, then initial

				parameters values will only be sent after some

				consumer makes a request.

- qcom,enable-with-pin-ctrl:   Double in which the first element corresponds to

				the pin control enable parameter value to send

				when all consumers have requested the regulator

				to be disabled.  The second element corresponds

				to the pin control enable parameter value to

				send when any consumer has requested the

				regulator to be enabled.  Each element supports

				the same set of values as the

				qcom,init-pin-ctrl-enable property listed below.

The following properties specify initial values for parameters to be sent to the

RPM in regulator requests.

- qcom,init-enable:            0 = regulator disabled

			       1 = regulator enabled

- qcom,init-voltage:           Voltage in uV

- qcom,init-current:           Current in mA

- qcom,init-ldo-mode:          Operating mode to be used with LDO regulators

				Supported values are:

					0 = mode determined by current requests

					1 = force HPM (NPM)

- qcom,init-smps-mode:         Operating mode to be used with SMPS regulators

				Supported values are:

					0 = auto; hardware determines mode

					1 = mode determined by current requests

					2 = force HPM (PWM)

- qcom,init-bob-mode:          Operating mode to be used with BoB regulators

				Supported values are:

					0 = pass; use priority order

					1 = force PFM

					2 = auto; hardware determines mode

					3 = force PWM

- qcom,init-pin-ctrl-enable:   Bit mask specifying which hardware pins should be

				used to enable the regulator, if any; supported

				bits are:

					0 = ignore all hardware enable signals

					BIT(0) = follow HW0_EN signal

					BIT(1) = follow HW1_EN signal

					BIT(2) = follow HW2_EN signal

					BIT(3) = follow HW3_EN signal

- qcom,init-pin-ctrl-mode:     Bit mask specifying which hardware pins should be

				used to force the regulator into high power

				mode, if any.  Supported bits are:

					0 = ignore all hardware enable signals

					BIT(0) = follow HW0_EN signal

					BIT(1) = follow HW1_EN signal

					BIT(2) = follow HW2_EN signal

					BIT(3) = follow HW3_EN signal

					BIT(4) = follow PMIC awake state

- qcom,init-pin-ctrl-voltage1: Minimum voltage in micro-volts to use while pin

				control 1 is enabled. This property only

				applies to BoB type regulators.

- qcom,init-pin-ctrl-voltage2: Minimum voltage in micro-volts to use while pin

				control 2 is enabled. This property only

				applies to BoB type regulators.

- qcom,init-pin-ctrl-voltage3: Minimum voltage in micro-volts to use while pin

				control 3 is enabled. This property only

				applies to BoB type regulators.

- qcom,init-frequency:         Switching frequency divisor for SMPS regulators.

				Supported values are n = 0 to 31 where

				freq = 19.2 MHz / (n + 1).

- qcom,init-head-room:         Voltage head room in mV required for the

				regulator.  This head room value should be used

				in situations where the device connected to the

				output of the regulator has low noise tolerance.

				Note that the RPM independently enforces a

				safety head room value for subregulated LDOs

				which is sufficient to account for LDO drop-out

				voltage.

- qcom,init-quiet-mode:        Specify that quiet mode is needed for an SMPS

				regulator in order to have lower output noise.

				Supported values are:

					0 = No quiet mode

					1 = Quiet mode

					2 = Super quiet mode

- qcom,init-freq-reason:       Consumer requiring specified frequency for an

				SMPS regulator.  Supported values are:

					0 = None

					1 = Bluetooth

					2 = GPS

					4 = WLAN

					8 = WAN

- qcom,init-voltage-corner:    Performance corner to use in order to determine

				voltage set point.  This value corresponds to

				the actual value that will be sent and is not

				incremented by 1 like the values used inside of

				the regulator framework.  The meaning of corner

				values is set by the RPM.  It is possible that

				different regulators on a given platform or

				similar regulators on different platforms will

				utilize different corner values.  These are

				corner values supported on MSM8974 for PMIC

				PM8841 SMPS 2 (VDD_Dig); nominal voltages for

				these corners are also shown:

					0 = None         (don't care)

					1 = Retention    (0.5000 V)

					2 = SVS Krait    (0.7250 V)

					3 = SVS SOC      (0.8125 V)

					4 = Normal       (0.9000 V)

					5 = Turbo        (0.9875 V)

					6 = Super Turbo  (1.0500 V)

- qcom,init-disallow-bypass:   Specify that bypass mode should not be used for a

				given LDO regulator.  When in bypass mode, an

				LDO performs no regulation and acts as a simple

				switch.  The RPM can utilize this mode for an

				LDO that is subregulated from an SMPS when it is

				possible to reduce the SMPS voltage to the

				desired LDO output level.  Bypass mode may be

				disallowed if lower LDO output noise is

				required.  Supported values are:

					0 = Allow RPM to utilize LDO bypass mode

						if possible

					1 = Disallow LDO bypass mode

- qcom,init-voltage-floor-corner:  Minimum performance corner to use if any

				processor in the system is awake.  This property

				supports the same values as

				qcom,init-voltage-corner.

- qcom,init-voltage-level:     Performance level to use in order to determine

				voltage set point. The meaning of level

				values is set by the RPM. It is possible that

				different regulators on a given platform or

				similar regulators on different platforms will

				utilize different level values. These are

				level values supported on MSM8952 for PMIC

				PM8952 SMPS 2 (VDD_Dig); nominal voltages for

				these level are also shown:

					16  = Retention    (0.5000 V)

					128 = SVS          (1.0500 V)

					192 = SVS+         (1.1550 V)

					256 = Normal       (1.2250 V)

					320 = Normal+      (1.2875 V)

					384 = Turbo        (1.3500 V)

- qcom,init-voltage-floor-level:   Minimum performance level to use if any

				processor in the system is awake. This property

				supports the same values as

				qcom,init-voltage-level.

All properties specified within the core regulator framework can also be used in

second level nodes.  These bindings can be found in:

Documentation/devicetree/bindings/regulator/regulator.txt.

Examples:

rpm-regulator-smpb1 {

	qcom,resource-name = "smpb";

	qcom,resource-id = <1>;

	qcom,regulator-type = <1>;

	qcom,hpm-min-load = <100000>;

	compatible = "qcom,rpm-smd-regulator-resource";

	status = "disabled";

	pm8841_s1: regulator-s1 {

		regulator-name = "8841_s1";

		qcom,set = <3>;

		regulator-min-microvolt = <900000>;

		regulator-max-microvolt = <1150000>;

		qcom,init-voltage = <1150000>;

		compatible = "qcom,rpm-smd-regulator";

	};

	pm8841_s1_ao: regulator-s1-ao {

		regulator-name = "8841_s1_ao";

		qcom,set = <1>;

		regulator-min-microvolt = <900000>;

		regulator-max-microvolt = <1150000>;

		compatible = "qcom,rpm-smd-regulator";

	};

	pm8841_s1_corner: regulator-s1-corner {

		regulator-name = "8841_s1_corner";

		qcom,set = <3>;

		regulator-min-microvolt = <1>;

		regulator-max-microvolt = <6>;

		qcom,init-voltage-corner = <3>;

		qcom,use-voltage-corner;

		compatible = "qcom,rpm-smd-regulator";

	};

};

rpm-regulator-ldoa2 {

	qcom,resource-name = "ldoa";

	qcom,resource-id = <2>;

	qcom,regulator-type = <0>;

	qcom,hpm-min-load = <10000>;

	compatible = "qcom,rpm-smd-regulator-resource";

	regulator-l2 {

		compatible = "qcom,rpm-smd-regulator";

		regulator-name = "8941_l2";

		qcom,set = <3>;

		regulator-min-microvolt = <1225000>;

		regulator-max-microvolt = <1225000>;

		qcom,init-voltage = <1225000>;

	};

	regulator-l2-pin-ctrl {

		compatible = "qcom,rpm-smd-regulator";

		regulator-name = "8941_l2_pin_ctrl";

		qcom,set = <3>;

		regulator-min-microvolt = <1225000>;

		regulator-max-microvolt = <1225000>;

		qcom,init-voltage = <1225000>;

		qcom,enable-with-pin-ctrl = <0 1>;

	};

};

	  control allows for voting on regulator state between multiple

	  processors within the SoC.

config REGULATOR_RPM_SMD

	bool "RPM SMD regulator driver"

	depends on OF

	depends on MSM_RPM_SMD

	help

	  Compile in support for the RPM SMD regulator driver which is used for

	  setting voltages and other parameters of the various power rails

	  supplied by some Qualcomm PMICs. The RPM SMD regulator driver should

	  be used on systems which contain an RPM which communicates with the

	  application processor over SMD.

config REGULATOR_STUB

	tristate "Stub Regulator"

	help

obj-$(CONFIG_REGULATOR_WM8350) += wm8350-regulator.o

obj-$(CONFIG_REGULATOR_WM8400) += wm8400-regulator.o

obj-$(CONFIG_REGULATOR_WM8994) += wm8994-regulator.o

obj-$(CONFIG_REGULATOR_RPM_SMD) += rpm-smd-regulator.o

obj-$(CONFIG_REGULATOR_RPMH) += rpmh-regulator.o

obj-$(CONFIG_REGULATOR_STUB) += stub-regulator.o

/* Copyright (c) 2015, 2017 The Linux Foundation. All rights reserved.

 *

 * This program is free software; you can redistribute it and/or modify

 * it under the terms of the GNU General Public License version 2 and

 * only version 2 as published by the Free Software Foundation.

 *

 * This program is distributed in the hope that it will be useful,

 * but WITHOUT ANY WARRANTY; without even the implied warranty of

 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the

 * GNU General Public License for more details.

 */

#ifndef __QCOM_RPM_SMD_REGULATOR_H

#define __QCOM_RPM_SMD_REGULATOR_H

#define RPM_SMD_REGULATOR_LEVEL_NONE		0

#define RPM_SMD_REGULATOR_LEVEL_RETENTION	16

#define RPM_SMD_REGULATOR_LEVEL_RETENTION_PLUS	32

#define RPM_SMD_REGULATOR_LEVEL_MIN_SVS		48

#define RPM_SMD_REGULATOR_LEVEL_LOW_SVS		64

#define RPM_SMD_REGULATOR_LEVEL_SVS		128

#define RPM_SMD_REGULATOR_LEVEL_SVS_PLUS	192

#define RPM_SMD_REGULATOR_LEVEL_NOM		256

#define RPM_SMD_REGULATOR_LEVEL_NOM_PLUS	320

#define RPM_SMD_REGULATOR_LEVEL_TURBO		384

#define RPM_SMD_REGULATOR_LEVEL_TURBO_NO_CPR	416

#define RPM_SMD_REGULATOR_LEVEL_BINNING		512

#endif