wcnss: Add wcnss snapshot to msm-4.14

* Qualcomm Technologies Inc. WCNSS Platform Driver

WCNSS driver is the platform driver. It is used for performing the cold

boot-up of the wireless device. It is responsible for adjusting

the necessary I/O rails and enabling appropriate gpios for wireless

connectivity subsystem.

Required properties:

- compatible: "wcnss_wlan"

- reg: physical address and length of the register set for the device.

- reg-names: "wcnss_mmio", "wcnss_fiq", "pronto_phy_base", "riva_phy_base",

	"riva_ccu_base", "pronto_a2xb_base", "pronto_ccpu_base",

	"pronto_saw2_base", "wlan_tx_phy_aborts","wlan_brdg_err_source",

	"wlan_tx_status", "alarms_txctl", "alarms_tactl",

	"pronto_mcu_base", "pronto_qfuse".

- interupts: Pronto to Apps interrupts for tx done and rx pending.

- qcom,pronto-vddmx-supply: regulator to supply pronto pll.

- qcom,pronto-vddcx-supply: voltage corner regulator to supply WLAN/BT/FM

digital module.

- qcom,pronto-vddpx-supply: regulator to supply WLAN DAC.

- qcom,iris-vddxo-supply  : regulator to supply RF XO.

- qcom,iris-vddrfa-supply : regulator to supply RFA digital.

- qcom,iris-vddpa-supply  : regulator to supply RF PA.

- qcom,iris-vdddig-supply : regulator to supply RF digital(BT/FM).

- gpios: gpio numbers to configure 5-wire interface of WLAN connectivity

- qcom,has-48mhz-xo: boolean flag to determine the usage of 24MHz XO from RF

- qcom,has-pronto-hw: boolean flag to determine the revId of the WLAN subsystem

- qcom,wcnss-adc_tm: ADC handle for vbatt notification APIs.

- qcom,wcnss-vadc: VADC handle for battery voltage notification APIs.

- pinctrl-<n> : Pinctrl states as described in bindings/pinctrl/pinctrl-bindings.txt

- pinctrl-names : Names corresponding to the numbered pinctrl states

- clocks: from common clock binding: handle to xo, rf_clk and wcnss snoc clocks.

- clock-names: Names of all the clocks that are accessed by the subsystem

- qcom,vdd-voltage-level: This property represents (nominal, min, max) voltage

for iris and pronto regulators in milli-volts.

- qcom,vdd-current: This property represents current value for

iris and pronto regulators in micro-amps.

Optional properties:

- qcom,has-autodetect-xo: boolean flag to determine whether Iris XO auto detect

should be performed during boot up.

- qcom,snoc-wcnss-clock-freq: indicates the wcnss snoc clock frequency in Hz.

If wcnss_snoc clock is specified in the list of clocks, this property needs

to be set to make it functional.

- qcom,wlan-rx-buff-count: WLAN RX buffer count is a configurable value,

using a smaller count for this buffer will reduce the memory usage.

- qcom,is-pronto-v3: boolean flag to determine the pronto hardware version

in use. subsequently correct workqueue will be used by DXE engine to push frames

in TX data path.

- qcom,is-dual-band-disable: boolean flag to determine the WLAN dual band

capability.

- qcom,is-pronto-vadc: boolean flag to determine Battery voltage feature

support for pronto hardware.

- qcom,wcnss-pm : <Core rail LDO#, PA rail LDO#, XO settling time,

RPM power collapse enabled, standalone power collapse enabled>

Power manager related parameter for LDO configuration.

	11     -  WCN CORE rail LDO number

	21     -  WCN PA rail LDO number

	1200   -  WCN XO settling time (usec)

	1      -  WCN RPM power collapse enabled

	1      -  WCN standalone power collapse enabled

	6      -  GPIO strength value

- qcom,has-vsys-adc-channel: boolean flag to determine which ADC HW channel need

to use for VBATT feature.

- qcom,has-a2xb-split-reg: boolean flag to determine A2xb split timeout limit

register is available or not.

Example:

qcom,wcnss-wlan@fb000000 {

	compatible = "qcom,wcnss_wlan";

	reg = <0xfb000000 0x280000>,

	    <0xf9011008 0x04>;

reg-names = "wcnss_mmio", "wcnss_fiq";

	interrupts = <0 145 0 0 146 0>;

	interrupt-names = "wcnss_wlantx_irq", "wcnss_wlanrx_irq";

	qcom,pronto-vddmx-supply = <&pm8841_s1>;

	qcom,pronto-vddcx-supply = <&pm8841_s2_corner>;

	qcom,pronto-vddpx-supply = <&pm8941_s3>;

	qcom,iris-vddxo-supply = <&pm8941_l6>;

	qcom,iris-vddrfa-supply = <&pm8941_l11>;

	qcom,iris-vddpa-supply = <&pm8941_l19>;

	qcom,iris-vdddig-supply = <&pm8941_l3>;

	gpios = <&msmgpio 36 0>, <&msmgpio 37 0>, <&msmgpio 38 0>,

	      <&msmgpio 39 0>, <&msmgpio 40 0>;

	qcom,has-48mhz-xo;

	qcom,is-pronto-vt;

	qcom,wlan-rx-buff-count = <512>;

	qcom,has-pronto-hw;

	qcom,wcnss-adc_tm = <&pm8226_adc_tm>;

	pinctrl-names = "wcnss_default", "wcnss_sleep";

	pinctrl-0 = <&wcnss_default>;

	pinctrl-1 = <&wcnss_sleep>;

	pinctrl-2 = <&wcnss_gpio_default>;

	clocks = <&clock_rpm clk_xo_wlan_clk>,

	       <&clock_rpm clk_rf_clk2>,

	       <&clock_debug clk_gcc_debug_mux>,

	       <&clock_gcc clk_wcnss_m_clk>,

	       <&clock_gcc clk_snoc_wcnss_a_clk>;

	clock-names = "xo", "rf_clk", "measure", "wcnss_debug",

		"snoc_wcnss";

	qcom,snoc-wcnss-clock-freq = <200000000>;

	qcom,wcnss-pm = <11 21 1200 1 1 6>;

};

	  CPUs can be assigned to the other guest OS by the hypervisor.

	  An offline CPU is considered as a reserved CPU since this OS can't use

	  it.

source "drivers/soc/qcom/wcnss/Kconfig"

obj-$(CONFIG_QCOM_ADSP_MANUAL_VOTE) += adsp_vote_qmi.o adsp_lpm_voting_v01.o

obj-$(CONFIG_CPU_V7) += idle-v7.o

obj-$(CONFIG_MSM_BAM_DMUX) += bam_dmux.o

obj-$(CONFIG_WCNSS_CORE) += wcnss/

config WCNSS_CORE

	tristate "Qualcomm Technologies Inc. WCNSS CORE driver"

	select WIRELESS_EXT

	select WEXT_PRIV

	select WEXT_CORE

	select WEXT_SPY

	help

	  This module adds support for WLAN connectivity subsystem

	  This module is responsible for communicating WLAN on/off

	  Core driver for the Qualcomm Technologies Inc. WCNSS triple play

	  connectivity subsystem, Enable WCNSS core platform driver

	  for WLAN.

config WCNSS_CORE_PRONTO

	tristate "Qualcomm Technologies Inc. WCNSS Pronto Support"

	depends on WCNSS_CORE

	help

	  Pronto Support for the Qualcomm Technologies Inc. WCNSS triple

	  play connectivity subsystem, Enable WCNSS core platform driver

	  for WLAN. This module adds support for WLAN connectivity subsystem

	  This module is responsible for communicating WLAN on/off

config WCNSS_REGISTER_DUMP_ON_BITE

	bool "Enable/disable WCNSS register dump when there is a WCNSS bite"

	depends on WCNSS_CORE_PRONTO

	help

	 When Apps receives a WDOG bite from WCNSS, collecting a register dump

	 of WCNSS is helpful to root cause the failure. WCNSS may not be

	 properly clocked in some WCNSS bite cases, and that may cause unclocked

	 register access failures. So this feature is to enable/disable the

	 register dump on WCNSS WDOG bite.

config CNSS_CRYPTO

	tristate "Enable CNSS crypto support"

	help

	  Add crypto support for the WLAN  driver module.

	  This feature enable wlan driver to use the crypto APIs exported

	  from cnss platform driver. This crypto APIs used to generate cipher

	  key and add support for the WLAN driver module security protocol.

# Makefile for WCNSS triple-play driver

wcnsscore-objs += wcnss_wlan.o wcnss_vreg.o

obj-$(CONFIG_WCNSS_CORE) += wcnsscore.o