Donate to e Foundation | Murena handsets with /e/OS | Own a part of Murena! Learn more

Commit 070f6b8f authored by Pengfei Liu's avatar Pengfei Liu
Browse files

ARM: dts: qcom: Add camera nodes for atoll qrd device 



Add camera nodes inlcuding EEPROM, Actuator, Sensor,
Flash for atoll qrd device.

Change-Id: Ibae9445ef02f84a8b441a6bbe881e779fbec33c8
Signed-off-by: default avatarPengfei Liu <pengfeiliu@codeaurora.org>
parent 91e8d2b6

arch/arm64/boot/dts/qcom/atoll-camera-sensor-qrd.dtsi

0 → 100644
+308 −0
Original line number Diff line number Diff line 
/*

 * Copyright (c) 2019, The Linux Foundation. All rights reserved.

 *

 * This program is free software; you can redistribute it and/or modify

 * it under the terms of the GNU General Public License version 2 and

 * only version 2 as published by the Free Software Foundation.

 *

 * This program is distributed in the hope that it will be useful,

 * but WITHOUT ANY WARRANTY; without even the implied warranty of

 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the

 * GNU General Public License for more details.

 */



#include <dt-bindings/clock/qcom,camcc-atoll.h>



&soc {

	led_flash_rear: qcom,camera-flash@0 {

		cell-index = <0>;

		reg = <0x00 0x00>;

		compatible = "qcom,camera-flash";

		flash-source = <&pm6150l_flash0 &pm6150l_flash1>;

		torch-source = <&pm6150l_torch0 &pm6150l_torch1>;

		switch-source = <&pm6150l_switch2 &pm6150l_switch2>;

		status = "ok";

	};



	led_flash_rear_aux: qcom,camera-flash@1 {

		cell-index = <1>;

		reg = <0x01 0x00>;

		compatible = "qcom,camera-flash";

		flash-source = <&pm6150l_flash0 &pm6150l_flash1>;

		torch-source = <&pm6150l_torch0 &pm6150l_torch1>;

		switch-source = <&pm6150l_switch2 &pm6150l_switch2>;

		status = "ok";

	};



	vreg_tof: regulator-dbb1 {

		compatible = "regulator-fixed";

		regulator-name = "vdd_tof";

		regulator-min-microvolt = <3600000>;

		regulator-max-microvolt = <3600000>;

		gpio = <&tlmm 118 GPIO_ACTIVE_HIGH>;

		startup-delay-us = <1000>;

		enable-active-high;

	};



	qcom,cam-res-mgr {

		compatible = "qcom,cam-res-mgr";

		status = "ok";

	};

};



&cam_cci0 {

	actuator_rear: qcom,actuator@0 {

		cell-index = <0>;

		reg = <0x0>;

		compatible = "qcom,actuator";

		cci-master = <0>;

		cam_vaf-supply = <&L6P>;

		regulator-names = "cam_vaf";

		rgltr-cntrl-support;

		rgltr-min-voltage = <2800000>;

		rgltr-max-voltage = <2800000>;

		rgltr-load-current = <100000>;

	};



	eeprom_rear: qcom,eeprom@0 {

		cell-index = <0>;

		reg = <0>;

		compatible = "qcom,eeprom";

		cam_vio-supply = <&L5P>;

		cam_vana-supply = <&L4P>;

		cam_vdig-supply = <&L1P>;

		cam_clk-supply = <&titan_top_gdsc>;

		cam_vaf-supply = <&L6P>;

		regulator-names = "cam_vio", "cam_vana", "cam_vdig",

			"cam_clk", "cam_vaf";

		rgltr-cntrl-support;

		rgltr-min-voltage = <1800000 2800000 1104000 0 2800000>;

		rgltr-max-voltage = <1800000 2800000 1104000 0 2800000>;

		rgltr-load-current = <0 80000 105000 0 100000>;

		gpio-no-mux = <0>;

		pinctrl-names = "cam_default", "cam_suspend";

		pinctrl-0 = <&cam_sensor_mclk0_active

				&cam_sensor_rear_active>;

		pinctrl-1 = <&cam_sensor_mclk0_suspend

				&cam_sensor_rear_suspend>;

		gpios = <&tlmm 13 0>,

			<&tlmm 30 0>;

		gpio-reset = <1>;

		gpio-req-tbl-num = <0 1>;

		gpio-req-tbl-flags = <1 0>;

		gpio-req-tbl-label = "CAMIF_MCLK0",

					"CAM_RESET0";

		sensor-mode = <0>;

		cci-master = <0>;

		status = "ok";

		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;

		clock-names = "cam_clk";

		clock-cntl-level = "turbo";

		clock-rates = <24000000>;

	};



	eeprom_front: qcom,eeprom@2 {

		cell-index = <2>;

		reg = <0x2>;

		compatible = "qcom,eeprom";

		cam_vio-supply = <&L5P>;

		cam_vana-supply = <&L3P>;

		cam_vdig-supply = <&L1P>;

		cam_clk-supply = <&titan_top_gdsc>;

		regulator-names = "cam_vio", "cam_vana", "cam_vdig",

			"cam_clk";

		rgltr-cntrl-support;

		rgltr-min-voltage = <1800000 2800000 1104000 0>;

		rgltr-max-voltage = <1800000 2800000 1104000 0>;

		rgltr-load-current = <0 80000 105000 0>;

		gpio-no-mux = <0>;

		pinctrl-names = "cam_default", "cam_suspend";

		pinctrl-0 = <&cam_sensor_mclk2_active

				 &cam_sensor_front_active>;

		pinctrl-1 = <&cam_sensor_mclk2_suspend

				 &cam_sensor_front_suspend>;

		gpios = <&tlmm 15 0>,

			<&tlmm 29 0>;

		gpio-reset = <1>;

		gpio-req-tbl-num = <0 1>;

		gpio-req-tbl-flags = <1 0>;

		gpio-req-tbl-label = "CAMIF_MCLK2",

					"CAM_RESET2";

		sensor-mode = <0>;

		cci-device = <0>;

		cci-master = <1>;

		status = "ok";

		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;

		clock-names = "cam_clk";

		clock-cntl-level = "turbo";

		clock-rates = <24000000>;

	};



	qcom,cam-sensor@0 {

		cell-index = <0>;

		compatible = "qcom,cam-sensor";

		reg = <0x0>;

		csiphy-sd-index = <0>;

		sensor-position-roll = <90>;

		sensor-position-pitch = <0>;

		sensor-position-yaw = <180>;

		led-flash-src = <&led_flash_rear>;

		eeprom-src = <&eeprom_rear>;

		actuator-src = <&actuator_rear>;

		cam_vio-supply = <&L5P>;

		cam_vana-supply = <&L4P>;

		cam_vdig-supply = <&L1P>;

		cam_clk-supply = <&titan_top_gdsc>;

		regulator-names = "cam_vio", "cam_vana", "cam_vdig",

			"cam_clk";

		rgltr-cntrl-support;

		rgltr-min-voltage = <1800000 2800000 1104000 0>;

		rgltr-max-voltage = <1800000 2800000 1104000 0>;

		rgltr-load-current = <0 80000 105000 0>;

		gpio-no-mux = <0>;

		pinctrl-names = "cam_default", "cam_suspend";

		pinctrl-0 = <&cam_sensor_mclk0_active

				&cam_sensor_rear_active>;

		pinctrl-1 = <&cam_sensor_mclk0_suspend

				&cam_sensor_rear_suspend>;

		gpios = <&tlmm 13 0>,

			<&tlmm 30 0>;

		gpio-reset = <1>;

		gpio-req-tbl-num = <0 1>;

		gpio-req-tbl-flags = <1 0>;

		gpio-req-tbl-label = "CAMIF_MCLK0",

					"CAM_RESET0";

		sensor-mode = <0>;

		cci-master = <0>;

		status = "ok";

		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;

		clock-names = "cam_clk";

		clock-cntl-level = "turbo";

		clock-rates = <24000000>;

	};



	qcom,cam-sensor@1 {

		cell-index = <1>;

		compatible = "qcom,cam-sensor";

		reg = <0x1>;

		csiphy-sd-index = <1>;

		sensor-position-roll = <90>;

		sensor-position-pitch = <0>;

		sensor-position-yaw = <180>;

		led-flash-src = <&led_flash_rear_aux>;

		cam_vio-supply = <&L5P>;

		cam_vana-supply = <&L3P>;

		cam_vdig-supply = <&L2P>;

		cam_clk-supply = <&titan_top_gdsc>;

		regulator-names = "cam_vio", "cam_vana", "cam_vdig",

			"cam_clk";

		rgltr-cntrl-support;

		rgltr-min-voltage = <1800000 2800000 1104000 0>;

		rgltr-max-voltage = <1800000 2800000 1104000 0>;

		rgltr-load-current = <0 80000 105000 0>;

		gpio-no-mux = <0>;

		pinctrl-names = "cam_default", "cam_suspend";

		pinctrl-0 = <&cam_sensor_mclk1_active

				&cam_sensor_rear2_active>;

		pinctrl-1 = <&cam_sensor_mclk1_suspend

				&cam_sensor_rear2_suspend>;

		gpios = <&tlmm 14 0>,

			<&tlmm 25 0>;

		gpio-reset = <1>;

		gpio-req-tbl-num = <0 1>;

		gpio-req-tbl-flags = <1 0>;

		gpio-req-tbl-label = "CAMIF_MCLK1",

					"CAM_RESET1";

		sensor-mode = <0>;

		cci-master = <1>;

		status = "ok";

		clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;

		clock-names = "cam_clk";

		clock-cntl-level = "turbo";

		clock-rates = <24000000>;

	};



	qcom,cam-sensor@2 {

		cell-index = <2>;

		compatible = "qcom,cam-sensor";

		reg = <0x2>;

		csiphy-sd-index = <2>;

		sensor-position-roll = <270>;

		sensor-position-pitch = <0>;

		sensor-position-yaw = <0>;

		eeprom-src = <&eeprom_front>;

		cam_vio-supply = <&L5P>;

		cam_vana-supply = <&L3P>;

		cam_vdig-supply = <&L1P>;

		cam_clk-supply = <&titan_top_gdsc>;

		regulator-names = "cam_vio", "cam_vana", "cam_vdig",

			"cam_clk";

		rgltr-cntrl-support;

		rgltr-min-voltage = <1800000 2800000 1104000 0>;

		rgltr-max-voltage = <1800000 2800000 1104000 0>;

		rgltr-load-current = <0 80000 105000 0>;

		gpio-no-mux = <0>;

		pinctrl-names = "cam_default", "cam_suspend";

		pinctrl-0 = <&cam_sensor_mclk2_active

				 &cam_sensor_front_active>;

		pinctrl-1 = <&cam_sensor_mclk2_suspend

				 &cam_sensor_front_suspend>;

		gpios = <&tlmm 15 0>,

			<&tlmm 29 0>;

		gpio-reset = <1>;

		gpio-req-tbl-num = <0 1>;

		gpio-req-tbl-flags = <1 0>;

		gpio-req-tbl-label = "CAMIF_MCLK2",

					"CAM_RESET2";

		sensor-mode = <0>;

		cci-device = <0>;

		cci-master = <1>;

		status = "ok";

		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;

		clock-names = "cam_clk";

		clock-cntl-level = "turbo";

		clock-rates = <24000000>;

	};

};



&cam_cci1 {

	qcom,cam-sensor@3 {

		cell-index = <3>;

		compatible = "qcom,cam-sensor";

		reg = <0x3>;

		csiphy-sd-index = <3>;

		sensor-position-roll = <90>;

		sensor-position-pitch = <0>;

		sensor-position-yaw = <180>;

		cam_vio-supply = <&L5P>;

		cam_vdig-supply = <&vreg_tof>;

		cam_clk-supply = <&titan_top_gdsc>;

		regulator-names = "cam_vio", "cam_vdig",

			"cam_clk";

		rgltr-cntrl-support;

		rgltr-min-voltage = <1800000 3600000 0>;

		rgltr-max-voltage = <1800000 3600000 0>;

		rgltr-load-current = <0 120000 0>;

		gpio-no-mux = <0>;

		pinctrl-names = "cam_default", "cam_suspend";

		pinctrl-0 = <&cam_sensor_mclk3_active

				 &cam_sensor_tof_active>;

		pinctrl-1 = <&cam_sensor_mclk3_suspend

				 &cam_sensor_tof_suspend>;

		gpios = <&tlmm 16 0>,

			<&tlmm 24 0>;

		gpio-reset = <1>;

		gpio-req-tbl-num = <0 1>;

		gpio-req-tbl-flags = <1 0>;

		gpio-req-tbl-label = "CAMIF_MCLK3",

					"CAM_RESET3";

		sensor-mode = <0>;

		cci-device = <1>;

		cci-master = <0>;

		status = "ok";

		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;

		clock-names = "cam_clk";

		clock-cntl-level = "turbo";

		clock-rates = <24000000>;

	};

};

arch/arm64/boot/dts/qcom/atoll-qrd.dtsi

+2 −0
Original line number Diff line number Diff line
@@ -15,6 +15,8 @@ 
#include <dt-bindings/iio/qcom,spmi-vadc.h>

#include <dt-bindings/input/input.h>



#include "atoll-camera-sensor-qrd.dtsi"



&soc {

	qrd_batterydata: qcom,battery-data {

		qcom,batt-id-range-pct = <15>;