Merge "ARM: dts: apq: Fix configuration of DSI panel on SBC8096" (c5eb2e59) · Commits · e / devices / android_kernel_xiaomi_markw

arch/arm/boot/dts/qcom/apq8096-sbc.dtsi

+27 −10

Original line number	Diff line number	Diff line
		@@ -324,36 +324,42 @@

		#include "msm8996-mdss-panels.dtsi"

		&dsi_hx8379a_fwvga_truly_vid {
		&dsi_dual_sharp_video {
		qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_pwm";
		qcom,mdss-dsi-bl-min-level = <1>;
		qcom,mdss-dsi-bl-max-level = <255>;
		qcom,mdss-dsi-bl-max-level = <4095>;
		qcom,mdss-dsi-bl-pmic-pwm-frequency = <50>;
		qcom,mdss-dsi-bl-pmic-bank-select = <0>;
		qcom,mdss-dsi-pwm-gpio = <&pm8994_gpios 5 0>;
		qcom,mdss-dsi-pwm-gpio = <&pm8994_gpios 6 0>;
		qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
		};


		&mdss_mdp {
		qcom,mdss-pref-prim-intf = "dsi";
		qcom,mdss-pref-prim-intf = "hdmi";
		};

		&mdss_dsi {
		hw-config = "single_dsi";
		hw-config = "split_dsi";
		};

		&mdss_dsi0 {
		qcom,dsi-pref-prim-pan = <&dsi_hx8379a_fwvga_truly_vid>;
		qcom,dsi-pref-prim-pan = <&dsi_dual_sharp_video>;
		pinctrl-names = "mdss_default", "mdss_sleep";
		pinctrl-0 = <&mdss_dsi_active &mdss_te_active &mdss_disp_bkl_active>;
		pinctrl-1 = <&mdss_dsi_suspend &mdss_te_suspend &mdss_disp_bkl_suspend>;
		pinctrl-0 = <&mdss_dsi_active &mdss_te_active>;
		pinctrl-1 = <&mdss_dsi_suspend &mdss_te_suspend>;
		qcom,platform-te-gpio = <&tlmm 10 0>;
		qcom,platform-reset-gpio = <&tlmm 8 0>;
		qcom,platform-bklight-en-gpio = <&pm8994_gpios 6 0>;
		};

		&mdss_dsi1 {
		status = "disabled";
		qcom,dsi-pref-prim-pan = <&dsi_dual_sharp_video>;
		pinctrl-names = "mdss_default", "mdss_sleep";
		pinctrl-0 = <&mdss_dsi_active &mdss_te_active>;
		pinctrl-1 = <&mdss_dsi_suspend &mdss_te_suspend>;
		qcom,platform-te-gpio = <&tlmm 10 0>;
		qcom,platform-reset-gpio = <&tlmm 8 0>;
		qcom,platform-bklight-en-gpio = <&pm8994_gpios 6 0>;
		};

		&labibb {
		@@ -644,6 +650,17 @@
		status = "okay";
		};

		gpio@c500 { /* GPIO 6 - lcd_bklt_reg_en */
		qcom,mode = <1>; /* DIGITAL OUT */
		qcom,output-type = <0>; /* CMOS logic */
		qcom,invert = <1>; /* output hight initially */
		qcom,vin-sel = <2>; /* 1.8 */
		qcom,src-sel = <0>; /* CONSTANT */
		qcom,out-strength = <1>;/* Low drive strength */
		qcom,master-en = <1>; /* ENABLE GPIO */
		status = "okay";
		};

		gpio@c700 { /* GPIO 8 - WLAN_EN */
		qcom,mode = <1>; /* Digital output*/
		qcom,pull = <4>; /* Pulldown 10uA */