Merge git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6 (9135f190) · Commits · e / devices / android_kernel_xiaomi_markw

Documentation/ide/ChangeLog.ide-tape.1995-2002

0 → 100644

+257 −0

Original line number	Diff line number	Diff line
		/*
		* Ver 0.1 Nov 1 95 Pre-working code :-)
		* Ver 0.2 Nov 23 95 A short backup (few megabytes) and restore procedure
		* was successful ! (Using tar cvf ... on the block
		* device interface).
		* A longer backup resulted in major swapping, bad
		* overall Linux performance and eventually failed as
		* we received non serial read-ahead requests from the
		* buffer cache.
		* Ver 0.3 Nov 28 95 Long backups are now possible, thanks to the
		* character device interface. Linux's responsiveness
		* and performance doesn't seem to be much affected
		* from the background backup procedure.
		* Some general mtio.h magnetic tape operations are
		* now supported by our character device. As a result,
		* popular tape utilities are starting to work with
		* ide tapes :-)
		* The following configurations were tested:
		* 1. An IDE ATAPI TAPE shares the same interface
		* and irq with an IDE ATAPI CDROM.
		* 2. An IDE ATAPI TAPE shares the same interface
		* and irq with a normal IDE disk.
		* Both configurations seemed to work just fine !
		* However, to be on the safe side, it is meanwhile
		* recommended to give the IDE TAPE its own interface
		* and irq.
		* The one thing which needs to be done here is to
		* add a "request postpone" feature to ide.c,
		* so that we won't have to wait for the tape to finish
		* performing a long media access (DSC) request (such
		* as a rewind) before we can access the other device
		* on the same interface. This effect doesn't disturb
		* normal operation most of the time because read/write
		* requests are relatively fast, and once we are
		* performing one tape r/w request, a lot of requests
		* from the other device can be queued and ide.c will
		* service all of them after this single tape request.
		* Ver 1.0 Dec 11 95 Integrated into Linux 1.3.46 development tree.
		* On each read / write request, we now ask the drive
		* if we can transfer a constant number of bytes
		* (a parameter of the drive) only to its buffers,
		* without causing actual media access. If we can't,
		* we just wait until we can by polling the DSC bit.
		* This ensures that while we are not transferring
		* more bytes than the constant referred to above, the
		* interrupt latency will not become too high and
		* we won't cause an interrupt timeout, as happened
		* occasionally in the previous version.
		* While polling for DSC, the current request is
		* postponed and ide.c is free to handle requests from
		* the other device. This is handled transparently to
		* ide.c. The hwgroup locking method which was used
		* in the previous version was removed.
		* Use of new general features which are provided by
		* ide.c for use with atapi devices.
		* (Programming done by Mark Lord)
		* Few potential bug fixes (Again, suggested by Mark)
		* Single character device data transfers are now
		* not limited in size, as they were before.
		* We are asking the tape about its recommended
		* transfer unit and send a larger data transfer
		* as several transfers of the above size.
		* For best results, use an integral number of this
		* basic unit (which is shown during driver
		* initialization). I will soon add an ioctl to get
		* this important parameter.
		* Our data transfer buffer is allocated on startup,
		* rather than before each data transfer. This should
		* ensure that we will indeed have a data buffer.
		* Ver 1.1 Dec 14 95 Fixed random problems which occurred when the tape
		* shared an interface with another device.
		* (poll_for_dsc was a complete mess).
		* Removed some old (non-active) code which had
		* to do with supporting buffer cache originated
		* requests.
		* The block device interface can now be opened, so
		* that general ide driver features like the unmask
		* interrupts flag can be selected with an ioctl.
		* This is the only use of the block device interface.
		* New fast pipelined operation mode (currently only on
		* writes). When using the pipelined mode, the
		* throughput can potentially reach the maximum
		* tape supported throughput, regardless of the
		* user backup program. On my tape drive, it sometimes
		* boosted performance by a factor of 2. Pipelined
		* mode is enabled by default, but since it has a few
		* downfalls as well, you may want to disable it.
		* A short explanation of the pipelined operation mode
		* is available below.
		* Ver 1.2 Jan 1 96 Eliminated pipelined mode race condition.
		* Added pipeline read mode. As a result, restores
		* are now as fast as backups.
		* Optimized shared interface behavior. The new behavior
		* typically results in better IDE bus efficiency and
		* higher tape throughput.
		* Pre-calculation of the expected read/write request
		* service time, based on the tape's parameters. In
		* the pipelined operation mode, this allows us to
		* adjust our polling frequency to a much lower value,
		* and thus to dramatically reduce our load on Linux,
		* without any decrease in performance.
		* Implemented additional mtio.h operations.
		* The recommended user block size is returned by
		* the MTIOCGET ioctl.
		* Additional minor changes.
		* Ver 1.3 Feb 9 96 Fixed pipelined read mode bug which prevented the
		* use of some block sizes during a restore procedure.
		* The character device interface will now present a
		* continuous view of the media - any mix of block sizes
		* during a backup/restore procedure is supported. The
		* driver will buffer the requests internally and
		* convert them to the tape's recommended transfer
		* unit, making performance almost independent of the
		* chosen user block size.
		* Some improvements in error recovery.
		* By cooperating with ide-dma.c, bus mastering DMA can
		* now sometimes be used with IDE tape drives as well.
		* Bus mastering DMA has the potential to dramatically
		* reduce the CPU's overhead when accessing the device,
		* and can be enabled by using hdparm -d1 on the tape's
		* block device interface. For more info, read the
		* comments in ide-dma.c.
		* Ver 1.4 Mar 13 96 Fixed serialize support.
		* Ver 1.5 Apr 12 96 Fixed shared interface operation, broken in 1.3.85.
		* Fixed pipelined read mode inefficiency.
		* Fixed nasty null dereferencing bug.
		* Ver 1.6 Aug 16 96 Fixed FPU usage in the driver.
		* Fixed end of media bug.
		* Ver 1.7 Sep 10 96 Minor changes for the CONNER CTT8000-A model.
		* Ver 1.8 Sep 26 96 Attempt to find a better balance between good
		* interactive response and high system throughput.
		* Ver 1.9 Nov 5 96 Automatically cross encountered filemarks rather
		* than requiring an explicit FSF command.
		* Abort pending requests at end of media.
		* MTTELL was sometimes returning incorrect results.
		* Return the real block size in the MTIOCGET ioctl.
		* Some error recovery bug fixes.
		* Ver 1.10 Nov 5 96 Major reorganization.
		* Reduced CPU overhead a bit by eliminating internal
		* bounce buffers.
		* Added module support.
		* Added multiple tape drives support.
		* Added partition support.
		* Rewrote DSC handling.
		* Some portability fixes.
		* Removed ide-tape.h.
		* Additional minor changes.
		* Ver 1.11 Dec 2 96 Bug fix in previous DSC timeout handling.
		* Use ide_stall_queue() for DSC overlap.
		* Use the maximum speed rather than the current speed
		* to compute the request service time.
		* Ver 1.12 Dec 7 97 Fix random memory overwriting and/or last block data
		* corruption, which could occur if the total number
		* of bytes written to the tape was not an integral
		* number of tape blocks.
		* Add support for INTERRUPT DRQ devices.
		* Ver 1.13 Jan 2 98 Add "speed == 0" work-around for HP COLORADO 5GB
		* Ver 1.14 Dec 30 98 Partial fixes for the Sony/AIWA tape drives.
		* Replace cli()/sti() with hwgroup spinlocks.
		* Ver 1.15 Mar 25 99 Fix SMP race condition by replacing hwgroup
		* spinlock with private per-tape spinlock.
		* Ver 1.16 Sep 1 99 Add OnStream tape support.
		* Abort read pipeline on EOD.
		* Wait for the tape to become ready in case it returns
		* "in the process of becoming ready" on open().
		* Fix zero padding of the last written block in
		* case the tape block size is larger than PAGE_SIZE.
		* Decrease the default disconnection time to tn.
		* Ver 1.16e Oct 3 99 Minor fixes.
		* Ver 1.16e1 Oct 13 99 Patches by Arnold Niessen,
		* niessen@iae.nl / arnold.niessen@philips.com
		* GO-1) Undefined code in idetape_read_position
		* according to Gadi's email
		* AJN-1) Minor fix asc == 11 should be asc == 0x11
		* in idetape_issue_packet_command (did effect
		* debugging output only)
		* AJN-2) Added more debugging output, and
		* added ide-tape: where missing. I would also
		* like to add tape->name where possible
		* AJN-3) Added different debug_level's
		* via /proc/ide/hdc/settings
		* "debug_level" determines amount of debugging output;
		* can be changed using /proc/ide/hdx/settings
		* 0 : almost no debugging output
		* 1 : 0+output errors only
		* 2 : 1+output all sensekey/asc
		* 3 : 2+follow all chrdev related procedures
		* 4 : 3+follow all procedures
		* 5 : 4+include pc_stack rq_stack info
		* 6 : 5+USE_COUNT updates
		* AJN-4) Fixed timeout for retension in idetape_queue_pc_tail
		* from 5 to 10 minutes
		* AJN-5) Changed maximum number of blocks to skip when
		* reading tapes with multiple consecutive write
		* errors from 100 to 1000 in idetape_get_logical_blk
		* Proposed changes to code:
		* 1) output "logical_blk_num" via /proc
		* 2) output "current_operation" via /proc
		* 3) Either solve or document the fact that `mt rewind' is
		* required after reading from /dev/nhtx to be
		* able to rmmod the idetape module;
		* Also, sometimes an application finishes but the
		* device remains `busy' for some time. Same cause ?
		* Proposed changes to release-notes:
		* 4) write a simple `quickstart' section in the
		* release notes; I volunteer if you don't want to
		* 5) include a pointer to video4linux in the doc
		* to stimulate video applications
		* 6) release notes lines 331 and 362: explain what happens
		* if the application data rate is higher than 1100 KB/s;
		* similar approach to lower-than-500 kB/s ?
		* 7) 6.6 Comparison; wouldn't it be better to allow different
		* strategies for read and write ?
		* Wouldn't it be better to control the tape buffer
		* contents instead of the bandwidth ?
		* 8) line 536: replace will by would (if I understand
		* this section correctly, a hypothetical and unwanted situation
		* is being described)
		* Ver 1.16f Dec 15 99 Change place of the secondary OnStream header frames.
		* Ver 1.17 Nov 2000 / Jan 2001 Marcel Mol, marcel@mesa.nl
		* - Add idetape_onstream_mode_sense_tape_parameter_page
		* function to get tape capacity in frames: tape->capacity.
		* - Add support for DI-50 drives( or any DI- drive).
		* - 'workaround' for read error/blank block around block 3000.
		* - Implement Early warning for end of media for Onstream.
		* - Cosmetic code changes for readability.
		* - Idetape_position_tape should not use SKIP bit during
		* Onstream read recovery.
		* - Add capacity, logical_blk_num and first/last_frame_position
		* to /proc/ide/hd?/settings.
		* - Module use count was gone in the Linux 2.4 driver.
		* Ver 1.17a Apr 2001 Willem Riede osst@riede.org
		* - Get drive's actual block size from mode sense block descriptor
		* - Limit size of pipeline
		* Ver 1.17b Oct 2002 Alan Stern <stern@rowland.harvard.edu>
		* Changed IDETAPE_MIN_PIPELINE_STAGES to 1 and actually used
		* it in the code!
		* Actually removed aborted stages in idetape_abort_pipeline
		* instead of just changing the command code.
		* Made the transfer byte count for Request Sense equal to the
		* actual length of the data transfer.
		* Changed handling of partial data transfers: they do not
		* cause DMA errors.
		* Moved initiation of DMA transfers to the correct place.
		* Removed reference to unallocated memory.
		* Made __idetape_discard_read_pipeline return the number of
		* sectors skipped, not the number of stages.
		* Replaced errant kfree() calls with __idetape_kfree_stage().
		* Fixed off-by-one error in testing the pipeline length.
		* Fixed handling of filemarks in the read pipeline.
		* Small code optimization for MTBSF and MTBSFM ioctls.
		* Don't try to unlock the door during device close if is
		* already unlocked!
		* Cosmetic fixes to miscellaneous debugging output messages.
		* Set the minimum /proc/ide/hd?/settings values for "pipeline",
		* "pipeline_min", and "pipeline_max" to 1.
		*/

Documentation/ide/ide-tape.txt

0 → 100644

+146 −0

Original line number	Diff line number	Diff line
		/*
		* IDE ATAPI streaming tape driver.
		*
		* This driver is a part of the Linux ide driver.
		*
		* The driver, in co-operation with ide.c, basically traverses the
		* request-list for the block device interface. The character device
		* interface, on the other hand, creates new requests, adds them
		* to the request-list of the block device, and waits for their completion.
		*
		* Pipelined operation mode is now supported on both reads and writes.
		*
		* The block device major and minor numbers are determined from the
		* tape's relative position in the ide interfaces, as explained in ide.c.
		*
		* The character device interface consists of the following devices:
		*
		* ht0 major 37, minor 0 first IDE tape, rewind on close.
		* ht1 major 37, minor 1 second IDE tape, rewind on close.
		* ...
		* nht0 major 37, minor 128 first IDE tape, no rewind on close.
		* nht1 major 37, minor 129 second IDE tape, no rewind on close.
		* ...
		*
		* The general magnetic tape commands compatible interface, as defined by
		* include/linux/mtio.h, is accessible through the character device.
		*
		* General ide driver configuration options, such as the interrupt-unmask
		* flag, can be configured by issuing an ioctl to the block device interface,
		* as any other ide device.
		*
		* Our own ide-tape ioctl's can be issued to either the block device or
		* the character device interface.
		*
		* Maximal throughput with minimal bus load will usually be achieved in the
		* following scenario:
		*
		* 1. ide-tape is operating in the pipelined operation mode.
		* 2. No buffering is performed by the user backup program.
		*
		* Testing was done with a 2 GB CONNER CTMA 4000 IDE ATAPI Streaming Tape Drive.
		*
		* Here are some words from the first releases of hd.c, which are quoted
		* in ide.c and apply here as well:
		*
		* \| Special care is recommended. Have Fun!
		*
		*
		* An overview of the pipelined operation mode.
		*
		* In the pipelined write mode, we will usually just add requests to our
		* pipeline and return immediately, before we even start to service them. The
		* user program will then have enough time to prepare the next request while
		* we are still busy servicing previous requests. In the pipelined read mode,
		* the situation is similar - we add read-ahead requests into the pipeline,
		* before the user even requested them.
		*
		* The pipeline can be viewed as a "safety net" which will be activated when
		* the system load is high and prevents the user backup program from keeping up
		* with the current tape speed. At this point, the pipeline will get
		* shorter and shorter but the tape will still be streaming at the same speed.
		* Assuming we have enough pipeline stages, the system load will hopefully
		* decrease before the pipeline is completely empty, and the backup program
		* will be able to "catch up" and refill the pipeline again.
		*
		* When using the pipelined mode, it would be best to disable any type of
		* buffering done by the user program, as ide-tape already provides all the
		* benefits in the kernel, where it can be done in a more efficient way.
		* As we will usually not block the user program on a request, the most
		* efficient user code will then be a simple read-write-read-... cycle.
		* Any additional logic will usually just slow down the backup process.
		*
		* Using the pipelined mode, I get a constant over 400 KBps throughput,
		* which seems to be the maximum throughput supported by my tape.
		*
		* However, there are some downfalls:
		*
		* 1. We use memory (for data buffers) in proportional to the number
		* of pipeline stages (each stage is about 26 KB with my tape).
		* 2. In the pipelined write mode, we cheat and postpone error codes
		* to the user task. In read mode, the actual tape position
		* will be a bit further than the last requested block.
		*
		* Concerning (1):
		*
		* 1. We allocate stages dynamically only when we need them. When
		* we don't need them, we don't consume additional memory. In
		* case we can't allocate stages, we just manage without them
		* (at the expense of decreased throughput) so when Linux is
		* tight in memory, we will not pose additional difficulties.
		*
		* 2. The maximum number of stages (which is, in fact, the maximum
		* amount of memory) which we allocate is limited by the compile
		* time parameter IDETAPE_MAX_PIPELINE_STAGES.
		*
		* 3. The maximum number of stages is a controlled parameter - We
		* don't start from the user defined maximum number of stages
		* but from the lower IDETAPE_MIN_PIPELINE_STAGES (again, we
		* will not even allocate this amount of stages if the user
		* program can't handle the speed). We then implement a feedback
		* loop which checks if the pipeline is empty, and if it is, we
		* increase the maximum number of stages as necessary until we
		* reach the optimum value which just manages to keep the tape
		* busy with minimum allocated memory or until we reach
		* IDETAPE_MAX_PIPELINE_STAGES.
		*
		* Concerning (2):
		*
		* In pipelined write mode, ide-tape can not return accurate error codes
		* to the user program since we usually just add the request to the
		* pipeline without waiting for it to be serviced. In case an error
		* occurs, I will report it on the next user request.
		*
		* In the pipelined read mode, subsequent read requests or forward
		* filemark spacing will perform correctly, as we preserve all blocks
		* and filemarks which we encountered during our excess read-ahead.
		*
		* For accurate tape positioning and error reporting, disabling
		* pipelined mode might be the best option.
		*
		* You can enable/disable/tune the pipelined operation mode by adjusting
		* the compile time parameters below.
		*
		*
		* Possible improvements.
		*
		* 1. Support for the ATAPI overlap protocol.
		*
		* In order to maximize bus throughput, we currently use the DSC
		* overlap method which enables ide.c to service requests from the
		* other device while the tape is busy executing a command. The
		* DSC overlap method involves polling the tape's status register
		* for the DSC bit, and servicing the other device while the tape
		* isn't ready.
		*
		* In the current QIC development standard (December 1995),
		* it is recommended that new tape drives will in addition
		* implement the ATAPI overlap protocol, which is used for the
		* same purpose - efficient use of the IDE bus, but is interrupt
		* driven and thus has much less CPU overhead.
		*
		* ATAPI overlap is likely to be supported in most new ATAPI
		* devices, including new ATAPI cdroms, and thus provides us
		* a method by which we can achieve higher throughput when
		* sharing a (fast) ATA-2 disk with any (slow) new ATAPI device.
		*/

drivers/ide/Kconfig

+1 −2

Original line number	Diff line number	Diff line
		@@ -216,8 +216,7 @@ config BLK_DEV_IDECD_VERBOSE_ERRORS
		memory, though.

		config BLK_DEV_IDETAPE
		tristate "Include IDE/ATAPI TAPE support (EXPERIMENTAL)"
		depends on EXPERIMENTAL
		tristate "Include IDE/ATAPI TAPE support"
		help
		If you have an IDE tape drive using the ATAPI protocol, say Y.
		ATAPI is a newer protocol used by IDE tape and CD-ROM drives,

drivers/ide/arm/bast-ide.c

+19 −1

Original line number	Diff line number	Diff line
		@@ -28,8 +28,10 @@ static int __init
		bastide_register(unsigned int base, unsigned int aux, int irq,
		ide_hwif_t **hwif)
		{
		ide_hwif_t *hwif;
		hw_regs_t hw;
		int i;
		u8 idx[4] = { 0xff, 0xff, 0xff, 0xff };

		memset(&hw, 0, sizeof(hw));

		@@ -44,8 +46,24 @@ bastide_register(unsigned int base, unsigned int aux, int irq,
		hw.io_ports[IDE_CONTROL_OFFSET] = aux + (6 * 0x20);
		hw.irq = irq;

		ide_register_hw(&hw, NULL, hwif);
		hwif = ide_deprecated_find_port(hw.io_ports[IDE_DATA_OFFSET]);
		if (hwif == NULL)
		goto out;

		i = hwif->index;

		if (hwif->present)
		ide_unregister(i, 0, 0);
		else if (!hwif->hold)
		ide_init_port_data(hwif, i);

		ide_init_port_hw(hwif, &hw);
		hwif->quirkproc = NULL;

		idx[0] = i;

		ide_device_add(idx, NULL);
		out:
		return 0;
		}

drivers/ide/arm/icside.c

+13 −12

File changed.

Preview size limit exceeded, changes collapsed.