iio: Add Nuvoton NAU7802 ADC driver (8b20be87) · Commits · e / devices / android_kernel_xiaomi_markw

Documentation/devicetree/bindings/iio/adc/nuvoton-nau7802.txt

0 → 100644

+18 −0

Original line number	Diff line number	Diff line
		* Nuvoton NAU7802 Analog to Digital Converter (ADC)

		Required properties:
		- compatible: Should be "nuvoton,nau7802"
		- reg: Should contain the ADC I2C address

		Optional properties:
		- nuvoton,vldo: Internal reference voltage in millivolts to be
		configured valid values are between 2400 mV and 4500 mV.
		- interrupts: IRQ line for the ADC. If not used the driver will use
		polling.

		Example:
		adc2: nau7802@2a {
		compatible = "nuvoton,nau7802";
		reg = <0x2a>;
		nuvoton,vldo = <3000>;
		};

drivers/iio/adc/Kconfig

+9 −0

Original line number	Diff line number	Diff line
		@@ -143,6 +143,15 @@ config MCP320X
		This driver can also be built as a module. If so, the module will be
		called mcp320x.

		config NAU7802
		tristate "Nuvoton NAU7802 ADC driver"
		depends on I2C
		help
		Say yes here to build support for Nuvoton NAU7802 ADC.

		To compile this driver as a module, choose M here: the
		module will be called nau7802.

		config TI_ADC081C
		tristate "Texas Instruments ADC081C021/027"
		depends on I2C

drivers/iio/adc/Makefile

+1 −0

Original line number	Diff line number	Diff line
		@@ -15,6 +15,7 @@ obj-$(CONFIG_EXYNOS_ADC) += exynos_adc.o
		obj-$(CONFIG_LP8788_ADC) += lp8788_adc.o
		obj-$(CONFIG_MAX1363) += max1363.o
		obj-$(CONFIG_MCP320X) += mcp320x.o
		obj-$(CONFIG_NAU7802) += nau7802.o
		obj-$(CONFIG_TI_ADC081C) += ti-adc081c.o
		obj-$(CONFIG_TI_AM335X_ADC) += ti_am335x_adc.o
		obj-$(CONFIG_VIPERBOARD_ADC) += viperboard_adc.o

drivers/iio/adc/nau7802.c

0 → 100644

+584 −0

Original line number	Diff line number	Diff line
		/*
		* Driver for the Nuvoton NAU7802 ADC
		*
		* Copyright 2013 Free Electrons
		*
		* Licensed under the GPLv2 or later.
		*/

		#include <linux/delay.h>
		#include <linux/i2c.h>
		#include <linux/interrupt.h>
		#include <linux/module.h>
		#include <linux/wait.h>
		#include <linux/log2.h>

		#include <linux/iio/iio.h>
		#include <linux/iio/sysfs.h>

		#define NAU7802_REG_PUCTRL 0x00
		#define NAU7802_PUCTRL_RR(x) (x << 0)
		#define NAU7802_PUCTRL_RR_BIT NAU7802_PUCTRL_RR(1)
		#define NAU7802_PUCTRL_PUD(x) (x << 1)
		#define NAU7802_PUCTRL_PUD_BIT NAU7802_PUCTRL_PUD(1)
		#define NAU7802_PUCTRL_PUA(x) (x << 2)
		#define NAU7802_PUCTRL_PUA_BIT NAU7802_PUCTRL_PUA(1)
		#define NAU7802_PUCTRL_PUR(x) (x << 3)
		#define NAU7802_PUCTRL_PUR_BIT NAU7802_PUCTRL_PUR(1)
		#define NAU7802_PUCTRL_CS(x) (x << 4)
		#define NAU7802_PUCTRL_CS_BIT NAU7802_PUCTRL_CS(1)
		#define NAU7802_PUCTRL_CR(x) (x << 5)
		#define NAU7802_PUCTRL_CR_BIT NAU7802_PUCTRL_CR(1)
		#define NAU7802_PUCTRL_AVDDS(x) (x << 7)
		#define NAU7802_PUCTRL_AVDDS_BIT NAU7802_PUCTRL_AVDDS(1)
		#define NAU7802_REG_CTRL1 0x01
		#define NAU7802_CTRL1_VLDO(x) (x << 3)
		#define NAU7802_CTRL1_GAINS(x) (x)
		#define NAU7802_CTRL1_GAINS_BITS 0x07
		#define NAU7802_REG_CTRL2 0x02
		#define NAU7802_CTRL2_CHS(x) (x << 7)
		#define NAU7802_CTRL2_CRS(x) (x << 4)
		#define NAU7802_SAMP_FREQ_320 0x07
		#define NAU7802_CTRL2_CHS_BIT NAU7802_CTRL2_CHS(1)
		#define NAU7802_REG_ADC_B2 0x12
		#define NAU7802_REG_ADC_B1 0x13
		#define NAU7802_REG_ADC_B0 0x14
		#define NAU7802_REG_ADC_CTRL 0x15

		#define NAU7802_MIN_CONVERSIONS 6

		struct nau7802_state {
		struct i2c_client *client;
		s32 last_value;
		struct mutex lock;
		struct mutex data_lock;
		u32 vref_mv;
		u32 conversion_count;
		u32 min_conversions;
		u8 sample_rate;
		u32 scale_avail[8];
		struct completion value_ok;
		};

		#define NAU7802_CHANNEL(chan) { \
		.type = IIO_VOLTAGE, \
		.indexed = 1, \
		.channel = (chan), \
		.scan_index = (chan), \
		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \
		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE) \| \
		BIT(IIO_CHAN_INFO_SAMP_FREQ) \
		}

		static const struct iio_chan_spec nau7802_chan_array[] = {
		NAU7802_CHANNEL(0),
		NAU7802_CHANNEL(1),
		};

		static const u16 nau7802_sample_freq_avail[] = {10, 20, 40, 80,
		10, 10, 10, 320};

		static IIO_CONST_ATTR_SAMP_FREQ_AVAIL("10 40 80 320");

		static struct attribute *nau7802_attributes[] = {
		&iio_const_attr_sampling_frequency_available.dev_attr.attr,
		NULL
		};

		static const struct attribute_group nau7802_attribute_group = {
		.attrs = nau7802_attributes,
		};

		static int nau7802_set_gain(struct nau7802_state *st, int gain)
		{
		int ret;

		mutex_lock(&st->lock);
		st->conversion_count = 0;

		ret = i2c_smbus_read_byte_data(st->client, NAU7802_REG_CTRL1);
		if (ret < 0)
		goto nau7802_sysfs_set_gain_out;
		ret = i2c_smbus_write_byte_data(st->client, NAU7802_REG_CTRL1,
		(ret & (~NAU7802_CTRL1_GAINS_BITS)) \|
		gain);

		nau7802_sysfs_set_gain_out:
		mutex_unlock(&st->lock);

		return ret;
		}

		static int nau7802_read_conversion(struct nau7802_state *st)
		{
		int data;

		mutex_lock(&st->data_lock);
		data = i2c_smbus_read_byte_data(st->client, NAU7802_REG_ADC_B2);
		if (data < 0)
		goto nau7802_read_conversion_out;
		st->last_value = data << 16;

		data = i2c_smbus_read_byte_data(st->client, NAU7802_REG_ADC_B1);
		if (data < 0)
		goto nau7802_read_conversion_out;
		st->last_value \|= data << 8;

		data = i2c_smbus_read_byte_data(st->client, NAU7802_REG_ADC_B0);
		if (data < 0)
		goto nau7802_read_conversion_out;
		st->last_value \|= data;

		st->last_value = sign_extend32(st->last_value, 23);

		nau7802_read_conversion_out:
		mutex_unlock(&st->data_lock);

		return data;
		}

		/*
		* Conversions are synchronised on the rising edge of NAU7802_PUCTRL_CS_BIT
		*/
		static int nau7802_sync(struct nau7802_state *st)
		{
		int ret;

		ret = i2c_smbus_read_byte_data(st->client, NAU7802_REG_PUCTRL);
		if (ret < 0)
		return ret;
		ret = i2c_smbus_write_byte_data(st->client, NAU7802_REG_PUCTRL,
		ret \| NAU7802_PUCTRL_CS_BIT);

		return ret;
		}

		static irqreturn_t nau7802_eoc_trigger(int irq, void *private)
		{
		struct iio_dev *indio_dev = private;
		struct nau7802_state *st = iio_priv(indio_dev);
		int status;

		status = i2c_smbus_read_byte_data(st->client, NAU7802_REG_PUCTRL);
		if (status < 0)
		return IRQ_HANDLED;

		if (!(status & NAU7802_PUCTRL_CR_BIT))
		return IRQ_NONE;

		if (nau7802_read_conversion(st) < 0)
		return IRQ_HANDLED;

		/*
		* Because there is actually only one ADC for both channels, we have to
		* wait for enough conversions to happen before getting a significant
		* value when changing channels and the values are far apart.
		*/
		if (st->conversion_count < NAU7802_MIN_CONVERSIONS)
		st->conversion_count++;
		if (st->conversion_count >= NAU7802_MIN_CONVERSIONS)
		complete_all(&st->value_ok);

		return IRQ_HANDLED;
		}

		static int nau7802_read_irq(struct iio_dev *indio_dev,
		struct iio_chan_spec const *chan,
		int *val)
		{
		struct nau7802_state *st = iio_priv(indio_dev);
		int ret;

		INIT_COMPLETION(st->value_ok);
		enable_irq(st->client->irq);

		nau7802_sync(st);

		/* read registers to ensure we flush everything */
		ret = nau7802_read_conversion(st);
		if (ret < 0)
		goto read_chan_info_failure;

		/* Wait for a conversion to finish */
		ret = wait_for_completion_interruptible_timeout(&st->value_ok,
		msecs_to_jiffies(1000));
		if (ret == 0)
		ret = -ETIMEDOUT;

		if (ret < 0)
		goto read_chan_info_failure;

		disable_irq(st->client->irq);

		*val = st->last_value;

		return IIO_VAL_INT;

		read_chan_info_failure:
		disable_irq(st->client->irq);

		return ret;
		}

		static int nau7802_read_poll(struct iio_dev *indio_dev,
		struct iio_chan_spec const *chan,
		int *val)
		{
		struct nau7802_state *st = iio_priv(indio_dev);
		int ret;

		nau7802_sync(st);

		/* read registers to ensure we flush everything */
		ret = nau7802_read_conversion(st);
		if (ret < 0)
		return ret;

		/*
		* Because there is actually only one ADC for both channels, we have to
		* wait for enough conversions to happen before getting a significant
		* value when changing channels and the values are far appart.
		*/
		do {
		ret = i2c_smbus_read_byte_data(st->client, NAU7802_REG_PUCTRL);
		if (ret < 0)
		return ret;

		while (!(ret & NAU7802_PUCTRL_CR_BIT)) {
		if (st->sample_rate != NAU7802_SAMP_FREQ_320)
		msleep(20);
		else
		mdelay(4);
		ret = i2c_smbus_read_byte_data(st->client,
		NAU7802_REG_PUCTRL);
		if (ret < 0)
		return ret;
		}

		ret = nau7802_read_conversion(st);
		if (ret < 0)
		return ret;
		if (st->conversion_count < NAU7802_MIN_CONVERSIONS)
		st->conversion_count++;
		} while (st->conversion_count < NAU7802_MIN_CONVERSIONS);

		*val = st->last_value;

		return IIO_VAL_INT;
		}

		static int nau7802_read_raw(struct iio_dev *indio_dev,
		struct iio_chan_spec const *chan,
		int val, int val2, long mask)
		{
		struct nau7802_state *st = iio_priv(indio_dev);
		int ret;

		switch (mask) {
		case IIO_CHAN_INFO_RAW:
		mutex_lock(&st->lock);
		/*
		* Select the channel to use
		* - Channel 1 is value 0 in the CHS register
		* - Channel 2 is value 1 in the CHS register
		*/
		ret = i2c_smbus_read_byte_data(st->client, NAU7802_REG_CTRL2);
		if (ret < 0) {
		mutex_unlock(&st->lock);
		return ret;
		}

		if (((ret & NAU7802_CTRL2_CHS_BIT) && !chan->channel) \|\|
		(!(ret & NAU7802_CTRL2_CHS_BIT) &&
		chan->channel)) {
		st->conversion_count = 0;
		ret = i2c_smbus_write_byte_data(st->client,
		NAU7802_REG_CTRL2,
		NAU7802_CTRL2_CHS(chan->channel) \|
		NAU7802_CTRL2_CRS(st->sample_rate));

		if (ret < 0) {
		mutex_unlock(&st->lock);
		return ret;
		}
		}

		if (st->client->irq)
		ret = nau7802_read_irq(indio_dev, chan, val);
		else
		ret = nau7802_read_poll(indio_dev, chan, val);

		mutex_unlock(&st->lock);
		return ret;

		case IIO_CHAN_INFO_SCALE:
		ret = i2c_smbus_read_byte_data(st->client, NAU7802_REG_CTRL1);
		if (ret < 0)
		return ret;

		/*
		* We have 24 bits of signed data, that means 23 bits of data
		* plus the sign bit
		*/
		*val = st->vref_mv;
		*val2 = 23 + (ret & NAU7802_CTRL1_GAINS_BITS);

		return IIO_VAL_FRACTIONAL_LOG2;

		case IIO_CHAN_INFO_SAMP_FREQ:
		*val = nau7802_sample_freq_avail[st->sample_rate];
		*val2 = 0;
		return IIO_VAL_INT;

		default:
		break;
		}

		return -EINVAL;
		}

		static int nau7802_write_raw(struct iio_dev *indio_dev,
		struct iio_chan_spec const *chan,
		int val, int val2, long mask)
		{
		struct nau7802_state *st = iio_priv(indio_dev);
		int i, ret;

		switch (mask) {
		case IIO_CHAN_INFO_SCALE:
		for (i = 0; i < ARRAY_SIZE(st->scale_avail); i++)
		if (val2 == st->scale_avail[i])
		return nau7802_set_gain(st, i);

		break;

		case IIO_CHAN_INFO_SAMP_FREQ:
		for (i = 0; i < ARRAY_SIZE(nau7802_sample_freq_avail); i++)
		if (val == nau7802_sample_freq_avail[i]) {
		mutex_lock(&st->lock);
		st->sample_rate = i;
		st->conversion_count = 0;
		ret = i2c_smbus_write_byte_data(st->client,
		NAU7802_REG_CTRL2,
		NAU7802_CTRL2_CRS(st->sample_rate));
		mutex_unlock(&st->lock);
		return ret;
		}

		break;

		default:
		break;
		}

		return -EINVAL;
		}

		static int nau7802_write_raw_get_fmt(struct iio_dev *indio_dev,
		struct iio_chan_spec const *chan,
		long mask)
		{
		return IIO_VAL_INT_PLUS_NANO;
		}

		static const struct iio_info nau7802_info = {
		.driver_module = THIS_MODULE,
		.read_raw = &nau7802_read_raw,
		.write_raw = &nau7802_write_raw,
		.write_raw_get_fmt = nau7802_write_raw_get_fmt,
		.attrs = &nau7802_attribute_group,
		};

		static int nau7802_probe(struct i2c_client *client,
		const struct i2c_device_id *id)
		{
		struct iio_dev *indio_dev;
		struct nau7802_state *st;
		struct device_node *np = client->dev.of_node;
		int i, ret;
		u8 data;
		u32 tmp = 0;

		if (!client->dev.of_node) {
		dev_err(&client->dev, "No device tree node available.\n");
		return -EINVAL;
		}

		indio_dev = iio_device_alloc(sizeof(*st));
		if (indio_dev == NULL)
		return -ENOMEM;

		st = iio_priv(indio_dev);

		i2c_set_clientdata(client, indio_dev);

		indio_dev->dev.parent = &client->dev;
		indio_dev->name = dev_name(&client->dev);
		indio_dev->modes = INDIO_DIRECT_MODE;
		indio_dev->info = &nau7802_info;

		st->client = client;

		/* Reset the device */
		ret = i2c_smbus_write_byte_data(st->client, NAU7802_REG_PUCTRL,
		NAU7802_PUCTRL_RR_BIT);
		if (ret < 0)
		goto error_free_indio;

		/* Enter normal operation mode */
		ret = i2c_smbus_write_byte_data(st->client, NAU7802_REG_PUCTRL,
		NAU7802_PUCTRL_PUD_BIT);
		if (ret < 0)
		goto error_free_indio;

		/*
		* After about 200 usecs, the device should be ready and then
		* the Power Up bit will be set to 1. If not, wait for it.
		*/
		udelay(210);
		ret = i2c_smbus_read_byte_data(st->client, NAU7802_REG_PUCTRL);
		if (ret < 0)
		goto error_free_indio;
		if (!(ret & NAU7802_PUCTRL_PUR_BIT))
		goto error_free_indio;

		of_property_read_u32(np, "nuvoton,vldo", &tmp);
		st->vref_mv = tmp;

		data = NAU7802_PUCTRL_PUD_BIT \| NAU7802_PUCTRL_PUA_BIT \|
		NAU7802_PUCTRL_CS_BIT;
		if (tmp >= 2400)
		data \|= NAU7802_PUCTRL_AVDDS_BIT;

		ret = i2c_smbus_write_byte_data(st->client, NAU7802_REG_PUCTRL, data);
		if (ret < 0)
		goto error_free_indio;
		ret = i2c_smbus_write_byte_data(st->client, NAU7802_REG_ADC_CTRL, 0x30);
		if (ret < 0)
		goto error_free_indio;

		if (tmp >= 2400) {
		data = NAU7802_CTRL1_VLDO((4500 - tmp) / 300);
		ret = i2c_smbus_write_byte_data(st->client, NAU7802_REG_CTRL1,
		data);
		if (ret < 0)
		goto error_free_indio;
		}

		/* Populate available ADC input ranges */
		for (i = 0; i < ARRAY_SIZE(st->scale_avail); i++)
		st->scale_avail[i] = (((u64)st->vref_mv) * 1000000000ULL)
		>> (23 + i);

		init_completion(&st->value_ok);

		/*
		* The ADC fires continuously and we can't do anything about
		* it. So we need to have the IRQ disabled by default, and we
		* will enable them back when we will need them..
		*/
		if (client->irq) {
		ret = request_threaded_irq(client->irq,
		NULL,
		nau7802_eoc_trigger,
		IRQF_TRIGGER_HIGH \| IRQF_ONESHOT,
		client->dev.driver->name,
		indio_dev);
		if (ret) {
		/*
		* What may happen here is that our IRQ controller is
		* not able to get level interrupt but this is required
		* by this ADC as when going over 40 sample per second,
		* the interrupt line may stay high between conversions.
		* So, we continue no matter what but we switch to
		* polling mode.
		*/
		dev_info(&client->dev,
		"Failed to allocate IRQ, using polling mode\n");
		client->irq = 0;
		} else
		disable_irq(client->irq);
		}

		if (!client->irq) {
		/*
		* We are polling, use the fastest sample rate by
		* default
		*/
		st->sample_rate = NAU7802_SAMP_FREQ_320;
		ret = i2c_smbus_write_byte_data(st->client, NAU7802_REG_CTRL2,
		NAU7802_CTRL2_CRS(st->sample_rate));
		if (ret)
		goto error_free_irq;
		}

		/* Setup the ADC channels available on the board */
		indio_dev->num_channels = ARRAY_SIZE(nau7802_chan_array);
		indio_dev->channels = nau7802_chan_array;

		mutex_init(&st->lock);
		mutex_init(&st->data_lock);

		ret = iio_device_register(indio_dev);
		if (ret < 0) {
		dev_err(&client->dev, "Couldn't register the device.\n");
		goto error_device_register;
		}

		return 0;

		error_device_register:
		mutex_destroy(&st->lock);
		mutex_destroy(&st->data_lock);
		error_free_irq:
		if (client->irq)
		free_irq(client->irq, indio_dev);
		error_free_indio:
		iio_device_free(indio_dev);

		return ret;
		}

		static int nau7802_remove(struct i2c_client *client)
		{
		struct iio_dev *indio_dev = i2c_get_clientdata(client);
		struct nau7802_state *st = iio_priv(indio_dev);

		iio_device_unregister(indio_dev);
		mutex_destroy(&st->lock);
		mutex_destroy(&st->data_lock);
		if (client->irq)
		free_irq(client->irq, indio_dev);
		iio_device_free(indio_dev);

		return 0;
		}

		static const struct i2c_device_id nau7802_i2c_id[] = {
		{ "nau7802", 0 },
		{ }
		};
		MODULE_DEVICE_TABLE(i2c, nau7802_i2c_id);

		static const struct of_device_id nau7802_dt_ids[] = {
		{ .compatible = "nuvoton,nau7802" },
		{},
		};
		MODULE_DEVICE_TABLE(of, nau7802_dt_ids);

		static struct i2c_driver nau7802_driver = {
		.probe = nau7802_probe,
		.remove = nau7802_remove,
		.id_table = nau7802_i2c_id,
		.driver = {
		.name = "nau7802",
		.of_match_table = of_match_ptr(nau7802_dt_ids),
		},
		};

		module_i2c_driver(nau7802_driver);

		MODULE_LICENSE("GPL");
		MODULE_DESCRIPTION("Nuvoton NAU7802 ADC Driver");
		MODULE_AUTHOR("Maxime Ripard <maxime.ripard@free-electrons.com>");
		MODULE_AUTHOR("Alexandre Belloni <alexandre.belloni@free-electrons.com>");