Merge branch 'next-samsung-devel-dt1' of...

* Insignal's Exynos4210 based Origen evaluation board

Origen low-cost evaluation board is based on Samsung's Exynos4210 SoC.

Required root node properties:

    - compatible = should be one or more of the following.

        (a) "samsung,smdkv310" - for Samsung's SMDKV310 eval board.

        (b) "samsung,exynos4210"  - for boards based on Exynos4210 SoC.

* Samsung's Exynos4210 based SMDKV310 evaluation board

SMDKV310 evaluation board is based on Samsung's Exynos4210 SoC.

Required root node properties:

    - compatible = should be one or more of the following.

        (a) "samsung,smdkv310" - for Samsung's SMDKV310 eval board.

        (b) "samsung,exynos4210"  - for boards based on Exynos4210 SoC.

* ARM PrimeCell PL330 DMA Controller

The ARM PrimeCell PL330 DMA controller can move blocks of memory contents

between memory and peripherals or memory to memory.

Required properties:

  - compatible: should include both "arm,pl330" and "arm,primecell".

  - reg: physical base address of the controller and length of memory mapped

    region.

  - interrupts: interrupt number to the cpu.

Example:

	pdma0: pdma@12680000 {

		compatible = "arm,pl330", "arm,primecell";

		reg = <0x12680000 0x1000>;

		interrupts = <99>;

	};

Client drivers (device nodes requiring dma transfers from dev-to-mem or

mem-to-dev) should specify the DMA channel numbers using a two-value pair

as shown below.

  [property name]  = <[phandle of the dma controller] [dma request id]>;

      where 'dma request id' is the dma request number which is connected

      to the client controller. The 'property name' is recommended to be

      of the form <name>-dma-channel.

  Example:  tx-dma-channel = <&pdma0 12>;

Samsung Exynos4 GPIO Controller

Required properties:

- compatible: Compatible property value should be "samsung,exynos4-gpio>".

- reg: Physical base address of the controller and length of memory mapped

  region.

- #gpio-cells: Should be 4. The syntax of the gpio specifier used by client nodes

  should be the following with values derived from the SoC user manual.

     <[phandle of the gpio controller node]

      [pin number within the gpio controller]

      [mux function]

      [pull up/down]

      [drive strength]>

  Values for gpio specifier:

  - Pin number: is a value between 0 to 7.

  - Pull Up/Down: 0 - Pull Up/Down Disabled.

                  1 - Pull Down Enabled.

                  3 - Pull Up Enabled.

  - Drive Strength: 0 - 1x,

                    1 - 3x,

                    2 - 2x,

                    3 - 4x

- gpio-controller: Specifies that the node is a gpio controller.

- #address-cells: should be 1.

- #size-cells: should be 1.

Example:

	gpa0: gpio-controller@11400000 {

		#address-cells = <1>;

		#size-cells = <1>;

		compatible = "samsung,exynos4-gpio";

		reg = <0x11400000 0x20>;

		#gpio-cells = <4>;

		gpio-controller;

	};

* Samsung's Keypad Controller device tree bindings

Samsung's Keypad controller is used to interface a SoC with a matrix-type

keypad device. The keypad controller supports multiple row and column lines.

A key can be placed at each intersection of a unique row and a unique column.

The keypad controller can sense a key-press and key-release and report the

event using a interrupt to the cpu.

Required SoC Specific Properties:

- compatible: should be one of the following

  - "samsung,s3c6410-keypad": For controllers compatible with s3c6410 keypad

    controller.

  - "samsung,s5pv210-keypad": For controllers compatible with s5pv210 keypad

    controller.

- reg: physical base address of the controller and length of memory mapped

  region.

- interrupts: The interrupt number to the cpu.

Required Board Specific Properties:

- samsung,keypad-num-rows: Number of row lines connected to the keypad

  controller.

- samsung,keypad-num-columns: Number of column lines connected to the

  keypad controller.

- row-gpios: List of gpios used as row lines. The gpio specifier for

  this property depends on the gpio controller to which these row lines

  are connected.

- col-gpios: List of gpios used as column lines. The gpio specifier for

  this property depends on the gpio controller to which these column

  lines are connected.

- Keys represented as child nodes: Each key connected to the keypad

  controller is represented as a child node to the keypad controller

  device node and should include the following properties.

  - keypad,row: the row number to which the key is connected.

  - keypad,column: the column number to which the key is connected.

  - linux,code: the key-code to be reported when the key is pressed

    and released.

Optional Properties specific to linux:

- linux,keypad-no-autorepeat: do no enable autorepeat feature.

- linux,keypad-wakeup: use any event on keypad as wakeup event.

Example:

	keypad@100A0000 {

		compatible = "samsung,s5pv210-keypad";

		reg = <0x100A0000 0x100>;

		interrupts = <173>;

		samsung,keypad-num-rows = <2>;

		samsung,keypad-num-columns = <8>;

		linux,input-no-autorepeat;

		linux,input-wakeup;

		row-gpios = <&gpx2 0 3 3 0

			     &gpx2 1 3 3 0>;

		col-gpios = <&gpx1 0 3 0 0

			     &gpx1 1 3 0 0

			     &gpx1 2 3 0 0

			     &gpx1 3 3 0 0

			     &gpx1 4 3 0 0

			     &gpx1 5 3 0 0

			     &gpx1 6 3 0 0

			     &gpx1 7 3 0 0>;

		key_1 {

			keypad,row = <0>;

			keypad,column = <3>;

			linux,code = <2>;

		};

		key_2 {

			keypad,row = <0>;

			keypad,column = <4>;

			linux,code = <3>;

		};

		key_3 {

			keypad,row = <0>;

			keypad,column = <5>;

			linux,code = <4>;

		};

	};