Merge "ARM: dts: msm: add sharp wqhd dual dsi panel for msm8996 fluid" (20a5b840) · Commits · e / devices / android_kernel_xiaomi_markw

arch/arm/boot/dts/qcom/msm8996-fluid.dtsi

+56 −20

Original line number	Diff line number	Diff line
		@@ -357,26 +357,6 @@
		qcom,invert = <0>; /* Output low initially */
		status = "okay";
		};

		};

		&pmi8994_mpps {
		mpp@a000 { /* MPP 1 */
		qcom,mode = <1>; /* Digital output */
		qcom,output-type = <0>; /* CMOS logic */
		qcom,vin-sel = <0>; /* S4 1.8V */
		qcom,src-sel = <7>; /* DTEST4 */
		qcom,master-en = <1>; /* Enable MPP */
		status = "okay";
		};

		mpp@a300 { /* MPP 4 */
		/* WLED FET */
		qcom,mode = <1>; /* DIGITAL OUT */
		qcom,vin-sel = <0>; /* VIN0 */
		qcom,master-en = <1>;
		status = "okay";
		};
		};

		&soc {
		@@ -574,3 +554,59 @@
		&blsp1_uart2 {
		status = "ok";
		};

		#include "msm8996-mdss-panels.dtsi"

		&mdss_mdp {
		qcom,mdss-pref-prim-intf = "dsi";
		};

		&mdss_dsi {
		hw-config = "split_dsi";
		};

		&mdss_dsi0 {
		qcom,dsi-pref-prim-pan = <&dsi_dual_sharp_video>;
		pinctrl-names = "mdss_default", "mdss_sleep";
		pinctrl-0 = <&mdss_dsi_active &mdss_te_active>;
		pinctrl-1 = <&mdss_dsi_suspend &mdss_te_suspend>;
		qcom,dsi-panel-bias-vreg;
		qcom,platform-reset-gpio = <&tlmm 8 0>;
		};

		&mdss_dsi1 {
		qcom,dsi-pref-prim-pan = <&dsi_dual_sharp_video>;
		};

		&dsi_dual_sharp_video {
		qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_wled";
		qcom,mdss-dsi-bl-min-level = <1>;
		qcom,mdss-dsi-bl-max-level = <4095>;
		qcom,cont-splash-enabled;
		qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
		};

		&labibb {
		status = "ok";
		qpnp,qpnp-labibb-mode = "lcd";
		qcom,qpnp-ibb-discharge-resistor = <32>;
		};

		&pmi8994_mpps {
		mpp@a000 { /* MPP 1 */
		qcom,mode = <1>; /* Digital output */
		qcom,output-type = <0>; /* CMOS logic */
		qcom,vin-sel = <0>; /* S4 1.8V */
		qcom,src-sel = <7>; /* DTEST4 */
		qcom,master-en = <1>; /* Enable MPP */
		status = "okay";
		};

		mpp@a300 { /* MPP 4 */
		/* WLED FET */
		qcom,mode = <1>; /* DIGITAL OUT */
		qcom,vin-sel = <0>; /* VIN0 */
		qcom,master-en = <1>;
		status = "okay";
		};
		};