Loading Documentation/networking/bonding.txt +52 −0 Original line number Diff line number Diff line Loading @@ -194,6 +194,48 @@ or, for backwards compatibility, the option value. E.g., The parameters are as follows: ad_select Specifies the 802.3ad aggregation selection logic to use. The possible values and their effects are: stable or 0 The active aggregator is chosen by largest aggregate bandwidth. Reselection of the active aggregator occurs only when all slaves of the active aggregator are down or the active aggregator has no slaves. This is the default value. bandwidth or 1 The active aggregator is chosen by largest aggregate bandwidth. Reselection occurs if: - A slave is added to or removed from the bond - Any slave's link state changes - Any slave's 802.3ad association state changes - The bond's adminstrative state changes to up count or 2 The active aggregator is chosen by the largest number of ports (slaves). Reselection occurs as described under the "bandwidth" setting, above. The bandwidth and count selection policies permit failover of 802.3ad aggregations when partial failure of the active aggregator occurs. This keeps the aggregator with the highest availability (either in bandwidth or in number of ports) active at all times. This option was added in bonding version 3.4.0. arp_interval Specifies the ARP link monitoring frequency in milliseconds. Loading Loading @@ -551,6 +593,16 @@ num_grat_arp affects only the active-backup mode. This option was added for bonding version 3.3.0. num_unsol_na Specifies the number of unsolicited IPv6 Neighbor Advertisements to be issued after a failover event. One unsolicited NA is issued immediately after the failover. The valid range is 0 - 255; the default value is 1. This option affects only the active-backup mode. This option was added for bonding version 3.4.0. primary A string (eth0, eth2, etc) specifying which slave is the Loading MAINTAINERS +6 −0 Original line number Diff line number Diff line Loading @@ -3853,6 +3853,12 @@ M: mhoffman@lightlink.com L: lm-sensors@lm-sensors.org S: Maintained SMSC911x ETHERNET DRIVER P: Steve Glendinning M: steve.glendinning@smsc.com L: netdev@vger.kernel.org S: Supported SMX UIO Interface P: Ben Nizette M: bn@niasdigital.com Loading drivers/net/Kconfig +15 −0 Original line number Diff line number Diff line Loading @@ -61,6 +61,7 @@ config DUMMY config BONDING tristate "Bonding driver support" depends on INET depends on IPV6 || IPV6=n ---help--- Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet Channels together. This is called 'Etherchannel' by Cisco, Loading Loading @@ -978,6 +979,20 @@ config SMC911X called smc911x. If you want to compile it as a module, say M here and read <file:Documentation/kbuild/modules.txt> config SMSC911X tristate "SMSC LAN911x/LAN921x families embedded ethernet support" depends on ARM || SUPERH select CRC32 select MII select PHYLIB ---help--- Say Y here if you want support for SMSC LAN911x and LAN921x families of ethernet controllers. To compile this driver as a module, choose M here and read <file:Documentation/networking/net-modules.txt>. The module will be called smsc911x. config NET_VENDOR_RACAL bool "Racal-Interlan (Micom) NI cards" depends on ISA Loading drivers/net/Makefile +1 −0 Original line number Diff line number Diff line Loading @@ -219,6 +219,7 @@ obj-$(CONFIG_S2IO) += s2io.o obj-$(CONFIG_MYRI10GE) += myri10ge/ obj-$(CONFIG_SMC91X) += smc91x.o obj-$(CONFIG_SMC911X) += smc911x.o obj-$(CONFIG_SMSC911X) += smsc911x.o obj-$(CONFIG_BFIN_MAC) += bfin_mac.o obj-$(CONFIG_DM9000) += dm9000.o obj-$(CONFIG_PASEMI_MAC) += pasemi_mac_driver.o Loading drivers/net/bonding/Makefile +3 −0 Original line number Diff line number Diff line Loading @@ -6,3 +6,6 @@ obj-$(CONFIG_BONDING) += bonding.o bonding-objs := bond_main.o bond_3ad.o bond_alb.o bond_sysfs.o ipv6-$(subst m,y,$(CONFIG_IPV6)) += bond_ipv6.o bonding-objs += $(ipv6-y) Loading
Documentation/networking/bonding.txt +52 −0 Original line number Diff line number Diff line Loading @@ -194,6 +194,48 @@ or, for backwards compatibility, the option value. E.g., The parameters are as follows: ad_select Specifies the 802.3ad aggregation selection logic to use. The possible values and their effects are: stable or 0 The active aggregator is chosen by largest aggregate bandwidth. Reselection of the active aggregator occurs only when all slaves of the active aggregator are down or the active aggregator has no slaves. This is the default value. bandwidth or 1 The active aggregator is chosen by largest aggregate bandwidth. Reselection occurs if: - A slave is added to or removed from the bond - Any slave's link state changes - Any slave's 802.3ad association state changes - The bond's adminstrative state changes to up count or 2 The active aggregator is chosen by the largest number of ports (slaves). Reselection occurs as described under the "bandwidth" setting, above. The bandwidth and count selection policies permit failover of 802.3ad aggregations when partial failure of the active aggregator occurs. This keeps the aggregator with the highest availability (either in bandwidth or in number of ports) active at all times. This option was added in bonding version 3.4.0. arp_interval Specifies the ARP link monitoring frequency in milliseconds. Loading Loading @@ -551,6 +593,16 @@ num_grat_arp affects only the active-backup mode. This option was added for bonding version 3.3.0. num_unsol_na Specifies the number of unsolicited IPv6 Neighbor Advertisements to be issued after a failover event. One unsolicited NA is issued immediately after the failover. The valid range is 0 - 255; the default value is 1. This option affects only the active-backup mode. This option was added for bonding version 3.4.0. primary A string (eth0, eth2, etc) specifying which slave is the Loading
MAINTAINERS +6 −0 Original line number Diff line number Diff line Loading @@ -3853,6 +3853,12 @@ M: mhoffman@lightlink.com L: lm-sensors@lm-sensors.org S: Maintained SMSC911x ETHERNET DRIVER P: Steve Glendinning M: steve.glendinning@smsc.com L: netdev@vger.kernel.org S: Supported SMX UIO Interface P: Ben Nizette M: bn@niasdigital.com Loading
drivers/net/Kconfig +15 −0 Original line number Diff line number Diff line Loading @@ -61,6 +61,7 @@ config DUMMY config BONDING tristate "Bonding driver support" depends on INET depends on IPV6 || IPV6=n ---help--- Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet Channels together. This is called 'Etherchannel' by Cisco, Loading Loading @@ -978,6 +979,20 @@ config SMC911X called smc911x. If you want to compile it as a module, say M here and read <file:Documentation/kbuild/modules.txt> config SMSC911X tristate "SMSC LAN911x/LAN921x families embedded ethernet support" depends on ARM || SUPERH select CRC32 select MII select PHYLIB ---help--- Say Y here if you want support for SMSC LAN911x and LAN921x families of ethernet controllers. To compile this driver as a module, choose M here and read <file:Documentation/networking/net-modules.txt>. The module will be called smsc911x. config NET_VENDOR_RACAL bool "Racal-Interlan (Micom) NI cards" depends on ISA Loading
drivers/net/Makefile +1 −0 Original line number Diff line number Diff line Loading @@ -219,6 +219,7 @@ obj-$(CONFIG_S2IO) += s2io.o obj-$(CONFIG_MYRI10GE) += myri10ge/ obj-$(CONFIG_SMC91X) += smc91x.o obj-$(CONFIG_SMC911X) += smc911x.o obj-$(CONFIG_SMSC911X) += smsc911x.o obj-$(CONFIG_BFIN_MAC) += bfin_mac.o obj-$(CONFIG_DM9000) += dm9000.o obj-$(CONFIG_PASEMI_MAC) += pasemi_mac_driver.o Loading
drivers/net/bonding/Makefile +3 −0 Original line number Diff line number Diff line Loading @@ -6,3 +6,6 @@ obj-$(CONFIG_BONDING) += bonding.o bonding-objs := bond_main.o bond_3ad.o bond_alb.o bond_sysfs.o ipv6-$(subst m,y,$(CONFIG_IPV6)) += bond_ipv6.o bonding-objs += $(ipv6-y)
