Merge "power: smb1351-charger: Add control for parallel charger configuration"

				property should be used with 'qcom,iterm-disabled'

				to ensure EOC detection in charger is disabled.

- qcom,force-hvdcp-2p0		Boolean value which allows to force hvdcp working on 2.0 mode.

- qcom,parallel-charger		Boolean value which enables the parallel charger.

- qcom,chg-vadc			Corresponding VADC device's phandle.

- qcom,chg-adc_tm		phandle to the corresponding VADC device to read the ADC channels.

- qcom,batt-cold-decidegc	Cold battery temperature in decidegC.

- qcom,batt-cool-mv:		Maximum cool battery target voltage in milli-volts.

- qcom,switch-freq:		Switching frequency of charger. Supported values:

				0 - 750 kHz, 1 - 1 MHz, 2 - 1.5 MHz, 3 - 3 MHz.

- qcom,parallel-en-pin-polarity Specify the polarity of enable signal controlled

				via pin in a parallel-charger configuration.

				0 - Active low and 1  - Active high.

- qcom,parallel-usb-min-current-ma:

				Minimum current which has to be drawn from USB when

				acting as the primary charger before enabling the

				parallel slave.

				This property needs to be specified if it's acting as

				the primary charger in parallel charger configuration.

- qcom,parallel-usb-9v-min-current-ma:

				Minimum current which has to be drawn from USB when

				acting as the primary charger before enabling the

				parallel slave. This value applies only for 9V charger

				adapters.

				This property needs to be specified if it's acting as

				the primary charger in parallel charger configuration.

- qcom,parallel-usb-12v-min-current-ma:

				Minimum current which has to be drawn from USB when

				acting as the primary charger before enabling the

				parallel slave. This value applies only for 12V charger

				adapters.

				This property needs to be specified if it's acting as

				the primary charger in parallel charger configuration.

- qcom,parallel-allowed-lowering-ma:

				The acceptable current drop from the initial limit(ICL)

				to keep parallel charging active. If charging current

				drops below this threshold, parallel charging is

				disabled.

				This property needs to be specified if it's acting as

				the primary charger in parallel charger configuration.

- qcom,parallel-main-chg-fcc-percent:

				Percentage of the fast charge current allotted to the

				primary charger when parallel charging is enabled and

				operational.

				If this property is not defined, the driver defaults

				to a 50% : 50% split between the primary charger and the

				slave charger.

- qcom,parallel-main-chg-icl-percent:

				Percentage of the input current allotted to the primary

				charger when parallel charging is enabled and

				operational.

				If this property is not defined, the driver defaults to

				a 50% : 50% split between the primary charger and the

				slave charger.

- qcom,parallel-charger:	Boolean value to indicate if it's a slave charger in

				parallel charger configuration.

- qcom,parallel-en-pin-polarity:

				Specify the active polarity of enable pin of the slave

				charger in parallel charger configuration:

					0 - Active low

					1 - Active high.

				If not specified the default value is active-low.

Example for standalone charger:

		qcom,batt-cool-ma = <350>;

		qcom,batt-warm-mv = <4200>;

		qcom,batt-cool-mv = <4200>;

		qcom,parallel-usb-min-current-ma = <1300>;

		qcom,parallel-usb-9v-min-current-ma = <900>;

		qcom,parallel-usb-12v-min-current-ma = <900>;

		qcom,parallel-allowed-lowering-ma = <500>;

		qcom,parallel-main-chg-fcc-percent = <50>;

		qcom,parallel-main-chg-icl-percent = <50>;

	};

};