Merge tag 'tegra-for-3.17-xusb-padctl' of...

Device tree binding for NVIDIA Tegra XUSB pad controller

========================================================

The Tegra XUSB pad controller manages a set of lanes, each of which can be

assigned to one out of a set of different pads. Some of these pads have an

associated PHY that must be powered up before the pad can be used.

This document defines the device-specific binding for the XUSB pad controller.

Refer to pinctrl-bindings.txt in this directory for generic information about

pin controller device tree bindings and ../phy/phy-bindings.txt for details on

how to describe and reference PHYs in device trees.

Required properties:

--------------------

- compatible: should be "nvidia,tegra124-xusb-padctl"

- reg: Physical base address and length of the controller's registers.

- resets: Must contain an entry for each entry in reset-names.

  See ../reset/reset.txt for details.

- reset-names: Must include the following entries:

  - padctl

- #phy-cells: Should be 1. The specifier is the index of the PHY to reference.

  See <dt-bindings/pinctrl/pinctrl-tegra-xusb.h> for the list of valid values.

Lane muxing:

------------

Child nodes contain the pinmux configurations following the conventions from

the pinctrl-bindings.txt document. Typically a single, static configuration is

given and applied at boot time.

Each subnode describes groups of lanes along with parameters and pads that

they should be assigned to. The name of these subnodes is not important. All

subnodes should be parsed solely based on their content.

Each subnode only applies the parameters that are explicitly listed. In other

words, if a subnode that lists a function but no pin configuration parameters

implies no information about any pin configuration parameters. Similarly, a

subnode that describes only an IDDQ parameter implies no information about

what function the pins are assigned to. For this reason even seemingly boolean

values are actually tristates in this binding: unspecified, off or on.

Unspecified is represented as an absent property, and off/on are represented

as integer values 0 and 1.

Required properties:

- nvidia,lanes: An array of strings. Each string is the name of a lane.

Optional properties:

- nvidia,function: A string that is the name of the function (pad) that the

  pin or group should be assigned to. Valid values for function names are

  listed below.

- nvidia,iddq: Enables IDDQ mode of the lane. (0: no, 1: yes)

Note that not all of these properties are valid for all lanes. Lanes can be

divided into three groups:

  - otg-0, otg-1, otg-2:

    Valid functions for this group are: "snps", "xusb", "uart", "rsvd".

    The nvidia,iddq property does not apply to this group.

  - ulpi-0, hsic-0, hsic-1:

    Valid functions for this group are: "snps", "xusb".

    The nvidia,iddq property does not apply to this group.

  - pcie-0, pcie-1, pcie-2, pcie-3, pcie-4, sata-0:

    Valid functions for this group are: "pcie", "usb3", "sata", "rsvd".

Example:

========

SoC file extract:

-----------------

	padctl@0,7009f000 {

		compatible = "nvidia,tegra124-xusb-padctl";

		reg = <0x0 0x7009f000 0x0 0x1000>;

		resets = <&tegra_car 142>;

		reset-names = "padctl";

		#phy-cells = <1>;

	};

Board file extract:

-------------------

	pcie-controller@0,01003000 {

		...

		phys = <&padctl 0>;

		phy-names = "pcie";

		...

	};

	...

	padctl: padctl@0,7009f000 {

		pinctrl-0 = <&padctl_default>;

		pinctrl-names = "default";

		padctl_default: pinmux {

			usb3 {

				nvidia,lanes = "pcie-0", "pcie-1";

				nvidia,function = "usb3";

				nvidia,iddq = <0>;

			};

			pcie {

				nvidia,lanes = "pcie-2", "pcie-3",

					       "pcie-4";

				nvidia,function = "pcie";

				nvidia,iddq = <0>;

			};

			sata {

				nvidia,lanes = "sata-0";

				nvidia,function = "sata";

				nvidia,iddq = <0>;

			};

		};

	};

	bool

	select PINCTRL_TEGRA

config PINCTRL_TEGRA_XUSB

	def_bool y if ARCH_TEGRA

	select GENERIC_PHY

	select PINCONF

	select PINMUX

config PINCTRL_TZ1090

	bool "Toumaz Xenif TZ1090 pin control driver"

	depends on SOC_TZ1090

obj-$(CONFIG_PINCTRL_TEGRA30)	+= pinctrl-tegra30.o

obj-$(CONFIG_PINCTRL_TEGRA114)	+= pinctrl-tegra114.o

obj-$(CONFIG_PINCTRL_TEGRA124)	+= pinctrl-tegra124.o

obj-$(CONFIG_PINCTRL_TEGRA_XUSB)	+= pinctrl-tegra-xusb.o

obj-$(CONFIG_PINCTRL_TZ1090)	+= pinctrl-tz1090.o

obj-$(CONFIG_PINCTRL_TZ1090_PDC)	+= pinctrl-tz1090-pdc.o

obj-$(CONFIG_PINCTRL_U300)	+= pinctrl-u300.o

#ifndef _DT_BINDINGS_PINCTRL_TEGRA_XUSB_H

#define _DT_BINDINGS_PINCTRL_TEGRA_XUSB_H 1

#define TEGRA_XUSB_PADCTL_PCIE 0

#define TEGRA_XUSB_PADCTL_SATA 1

#endif /* _DT_BINDINGS_PINCTRL_TEGRA_XUSB_H */