Merge 3.18-rc4 into tty-next. (394e849b) · Commits · e / devices / android_kernel_teracube_emerald

Documentation/devicetree/bindings/thermal/rcar-thermal.txt

+4 −1

Original line number	Diff line number	Diff line
		@@ -7,7 +7,10 @@ Required properties:
		- "renesas,thermal-r8a73a4" (R-Mobile AP6)
		- "renesas,thermal-r8a7779" (R-Car H1)
		- "renesas,thermal-r8a7790" (R-Car H2)
		- "renesas,thermal-r8a7791" (R-Car M2)
		- "renesas,thermal-r8a7791" (R-Car M2-W)
		- "renesas,thermal-r8a7792" (R-Car V2H)
		- "renesas,thermal-r8a7793" (R-Car M2-N)
		- "renesas,thermal-r8a7794" (R-Car E2)
		- reg : Address range of the thermal registers.
		The 1st reg will be recognized as common register
		if it has "interrupts".

Documentation/kernel-parameters.txt

+1 −1

Original line number	Diff line number	Diff line
		@@ -3621,7 +3621,7 @@ bytes respectively. Such letter suffixes can also be entirely omitted.

		usb-storage.delay_use=
		[UMS] The delay in seconds before a new device is
		scanned for Logical Units (default 5).
		scanned for Logical Units (default 1).

		usb-storage.quirks=
		[UMS] A list of quirks entries to supplement or

Documentation/video4linux/vivid.txt

+5 −7

Original line number	Diff line number	Diff line
		@@ -221,12 +221,11 @@ ccs_out_mode: specify the allowed video output crop/compose/scaling combination
		key, not quality.

		multiplanar: select whether each device instance supports multi-planar formats,
		and thus the V4L2 multi-planar API. By default the first device instance
		is single-planar, the second multi-planar, and it keeps alternating.
		and thus the V4L2 multi-planar API. By default device instances are
		single-planar.

		This module option can override that for each instance. Values are:

		0: use alternating single and multi-planar devices.
		1: this is a single-planar instance.
		2: this is a multi-planar instance.

		@@ -975,9 +974,8 @@ is set, then the alpha component is only used for the color red and set to
		0 otherwise.

		The driver has to be configured to support the multiplanar formats. By default
		the first driver instance is single-planar, the second is multi-planar, and it
		keeps alternating. This can be changed by setting the multiplanar module option,
		see section 1 for more details on that option.
		the driver instances are single-planar. This can be changed by setting the
		multiplanar module option, see section 1 for more details on that option.

		If the driver instance is using the multiplanar formats/API, then the first
		single planar format (YUYV) and the multiplanar NV16M and NV61M formats the
		@@ -1021,7 +1019,7 @@ the output overlay for the video output, turn on video looping and capture
		to see the blended framebuffer overlay that's being written to by the second
		instance. This setup would require the following commands:

		$ sudo modprobe vivid n_devs=2 node_types=0x10101,0x1 multiplanar=1,1
		$ sudo modprobe vivid n_devs=2 node_types=0x10101,0x1
		$ v4l2-ctl -d1 --find-fb
		/dev/fb1 is the framebuffer associated with base address 0x12800000
		$ sudo v4l2-ctl -d2 --set-fbuf fb=1

MAINTAINERS

+4 −8

Original line number	Diff line number	Diff line
		@@ -1543,6 +1543,7 @@ F: arch/arm/mach-pxa/include/mach/z2.h

		ARM/ZYNQ ARCHITECTURE
		M: Michal Simek <michal.simek@xilinx.com>
		R: Sören Brinkmann <soren.brinkmann@xilinx.com>
		L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
		W: http://wiki.xilinx.com
		T: git git://git.xilinx.com/linux-xlnx.git
		@@ -2071,8 +2072,9 @@ F: drivers/clocksource/bcm_kona_timer.c

		BROADCOM BCM2835 ARM ARCHITECTURE
		M: Stephen Warren <swarren@wwwdotorg.org>
		M: Lee Jones <lee@kernel.org>
		L: linux-rpi-kernel@lists.infradead.org (moderated for non-subscribers)
		T: git git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-rpi.git
		T: git git://git.kernel.org/pub/scm/linux/kernel/git/rpi/linux-rpi.git
		S: Maintained
		N: bcm2835

		@@ -7179,6 +7181,7 @@ F: drivers/crypto/picoxcell*

		PIN CONTROL SUBSYSTEM
		M: Linus Walleij <linus.walleij@linaro.org>
		L: linux-gpio@vger.kernel.org
		S: Maintained
		F: drivers/pinctrl/
		F: include/linux/pinctrl/
		@@ -8489,7 +8492,6 @@ F: arch/arm/mach-s3c24xx/bast-irq.c
		TI DAVINCI MACHINE SUPPORT
		M: Sekhar Nori <nsekhar@ti.com>
		M: Kevin Hilman <khilman@deeprootsystems.com>
		L: davinci-linux-open-source@linux.davincidsp.com (moderated for non-subscribers)
		T: git git://gitorious.org/linux-davinci/linux-davinci.git
		Q: http://patchwork.kernel.org/project/linux-davinci/list/
		S: Supported
		@@ -8499,7 +8501,6 @@ F: drivers/i2c/busses/i2c-davinci.c
		TI DAVINCI SERIES MEDIA DRIVER
		M: Lad, Prabhakar <prabhakar.csengg@gmail.com>
		L: linux-media@vger.kernel.org
		L: davinci-linux-open-source@linux.davincidsp.com (moderated for non-subscribers)
		W: http://linuxtv.org/
		Q: http://patchwork.linuxtv.org/project/linux-media/list/
		T: git git://linuxtv.org/mhadli/v4l-dvb-davinci_devices.git
		@@ -9709,11 +9710,6 @@ S: Maintained
		F: Documentation/hid/hiddev.txt
		F: drivers/hid/usbhid/

		USB/IP DRIVERS
		L: linux-usb@vger.kernel.org
		S: Orphan
		F: drivers/staging/usbip/

		USB ISP116X DRIVER
		M: Olav Kongas <ok@artecdesign.ee>
		L: linux-usb@vger.kernel.org

Makefile

+1 −1

Original line number	Diff line number	Diff line
		VERSION = 3
		PATCHLEVEL = 18
		SUBLEVEL = 0
		EXTRAVERSION = -rc3
		EXTRAVERSION = -rc4
		NAME = Diseased Newt

		# DOCUMENTATION