Merge remote-tracking branches 'spi/topic/bcm', 'spi/topic/dw' and...

Broadcom SPI controller

The Broadcom SPI controller is a SPI master found on various SOCs, including

BRCMSTB (BCM7XXX), Cygnus, NSP and NS2. The Broadcom Master SPI hw IP consits

of :

 MSPI : SPI master controller can read and write to a SPI slave device

 BSPI : Broadcom SPI in combination with the MSPI hw IP provides acceleration

	for flash reads and be configured to do single, double, quad lane

	io with 3-byte and 4-byte addressing support.

 Supported Broadcom SoCs have one instance of MSPI+BSPI controller IP.

 MSPI master can be used wihout BSPI. BRCMSTB SoCs have an additional instance

 of a MSPI master without the BSPI to use with non flash slave devices that

 use SPI protocol.

Required properties:

- #address-cells:

    Must be <1>, as required by generic SPI binding.

- #size-cells:

    Must be <0>, also as required by generic SPI binding.

- compatible:

    Must be one of :

    "brcm,spi-bcm-qspi", "brcm,spi-brcmstb-qspi" : MSPI+BSPI on BRCMSTB SoCs

    "brcm,spi-bcm-qspi", "brcm,spi-brcmstb-mspi" : Second Instance of MSPI

						   BRCMSTB  SoCs

    "brcm,spi-bcm-qspi", "brcm,spi-nsp-qspi"     : MSPI+BSPI on Cygnus, NSP

    "brcm,spi-bcm-qspi", "brcm,spi-ns2-qspi"     : NS2 SoCs

- reg:

    Define the bases and ranges of the associated I/O address spaces.

    The required range is MSPI controller registers.

- reg-names:

    First name does not matter, but must be reserved for the MSPI controller

    register range as mentioned in 'reg' above, and will typically contain

    - "bspi_regs": BSPI register range, not required with compatible

		   "spi-brcmstb-mspi"

    - "mspi_regs": MSPI register range is required for compatible strings

    - "intr_regs", "intr_status_reg" : Interrupt and status register for

      NSP, NS2, Cygnus SoC

- interrupts

    The interrupts used by the MSPI and/or BSPI controller.

- interrupt-names:

    Names of interrupts associated with MSPI

    - "mspi_halted" :

    - "mspi_done": Indicates that the requested SPI operation is complete.

    - "spi_lr_fullness_reached" : Linear read BSPI pipe full

    - "spi_lr_session_aborted"  : Linear read BSPI pipe aborted

    - "spi_lr_impatient" : Linear read BSPI requested when pipe empty

    - "spi_lr_session_done" : Linear read BSPI session done

- clocks:

    A phandle to the reference clock for this block.

Optional properties:

- native-endian

    Defined when using BE SoC and device uses BE register read/write

Recommended optional m25p80 properties:

- spi-rx-bus-width: Definition as per

                    Documentation/devicetree/bindings/spi/spi-bus.txt

Examples:

BRCMSTB SoC Example:

  SPI Master (MSPI+BSPI) for SPI-NOR access:

    spi@f03e3400 {

		#address-cells = <0x1>;

		#size-cells = <0x0>;

		compatible = "brcm,spi-brcmstb-qspi", "brcm,spi-brcmstb-qspi";

		reg = <0xf03e0920 0x4 0xf03e3400 0x188 0xf03e3200 0x50>;

		reg-names = "cs_reg", "mspi", "bspi";

		interrupts = <0x6 0x5 0x4 0x3 0x2 0x1 0x0>;

		interrupt-parent = <0x1c>;

		interrupt-names = "mspi_halted",

				  "mspi_done",

				  "spi_lr_overread",

				  "spi_lr_session_done",

				  "spi_lr_impatient",

				  "spi_lr_session_aborted",

				  "spi_lr_fullness_reached";

		clocks = <&hif_spi>;

		clock-names = "sw_spi";

		m25p80@0 {

			#size-cells = <0x2>;

			#address-cells = <0x2>;

			compatible = "m25p80";

			reg = <0x0>;

			spi-max-frequency = <0x2625a00>;

			spi-cpol;

			spi-cpha;

			m25p,fast-read;

			flash0.bolt@0 {

				reg = <0x0 0x0 0x0 0x100000>;

			};

			flash0.macadr@100000 {

				reg = <0x0 0x100000 0x0 0x10000>;

			};

			flash0.nvram@110000 {

				reg = <0x0 0x110000 0x0 0x10000>;

			};

			flash0.kernel@120000 {

				reg = <0x0 0x120000 0x0 0x400000>;

			};

			flash0.devtree@520000 {

				reg = <0x0 0x520000 0x0 0x10000>;

			};

			flash0.splash@530000 {

				reg = <0x0 0x530000 0x0 0x80000>;

			};

			flash0@0 {

				reg = <0x0 0x0 0x0 0x4000000>;

			};

		};

	};

    MSPI master for any SPI device :

	spi@f0416000 {

		#address-cells = <1>;

		#size-cells = <0>;

		clocks = <&upg_fixed>;

		compatible = "brcm,spi-brcmstb-qspi", "brcm,spi-brcmstb-mspi";

		reg = <0xf0416000 0x180>;

		reg-names = "mspi";

		interrupts = <0x14>;

		interrupt-parent = <&irq0_aon_intc>;

		interrupt-names = "mspi_done";

	};

iProc SoC Example:

    qspi: spi@18027200 {

	compatible = "brcm,spi-bcm-qspi", "brcm,spi-nsp-qspi";

	reg = <0x18027200 0x184>,

	      <0x18027000 0x124>,

	      <0x1811c408 0x004>,

	      <0x180273a0 0x01c>;

	reg-names = "mspi_regs", "bspi_regs", "intr_regs", "intr_status_reg";

	interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,

		     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,

		     <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,

		     <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,

		     <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,

		     <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,

		     <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;

	interrupt-names =

		     "spi_lr_fullness_reached",

		     "spi_lr_session_aborted",

		     "spi_lr_impatient",

		     "spi_lr_session_done",

		     "mspi_done",

		     "mspi_halted";

	clocks = <&iprocmed>;

	clock-names = "iprocmed";

	num-cs = <2>;

	#address-cells = <1>;

	#size-cells = <0>;

    };

 NS2 SoC Example:

	       qspi: spi@66470200 {

		       compatible = "brcm,spi-bcm-qspi", "brcm,spi-ns2-qspi";

		       reg = <0x66470200 0x184>,

			     <0x66470000 0x124>,

			     <0x67017408 0x004>,

			     <0x664703a0 0x01c>;

		       reg-names = "mspi", "bspi", "intr_regs",

			"intr_status_reg";

		       interrupts = <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>;

		       interrupt-names = "spi_l1_intr";

			clocks = <&iprocmed>;

			clock-names = "iprocmed";

			num-cs = <2>;

			#address-cells = <1>;

			#size-cells = <0>;

	       };

 m25p80 node for NSP, NS2

	 &qspi {

		      flash: m25p80@0 {

		      #address-cells = <1>;

		      #size-cells = <1>;

		      compatible = "m25p80";

		      reg = <0x0>;

		      spi-max-frequency = <12500000>;

		      m25p,fast-read;

		      spi-cpol;

		      spi-cpha;

		      partition@0 {

				  label = "boot";

				  reg = <0x00000000 0x000a0000>;

		      };

		      partition@a0000 {

				  label = "env";

				  reg = <0x000a0000 0x00060000>;

		      };

		      partition@100000 {

				  label = "system";

				  reg = <0x00100000 0x00600000>;

		      };

		      partition@700000 {

				  label = "rootfs";

				  reg = <0x00700000 0x01900000>;

		      };

	};

	  This enables support for the High Speed SPI controller present on

	  newer Broadcom BCM63XX SoCs.

config SPI_BCM_QSPI

	tristate "Broadcom BSPI and MSPI controller support"

	depends on ARCH_BRCMSTB || ARCH_BCM || ARCH_BCM_IPROC || COMPILE_TEST

	default ARCH_BCM_IPROC

	help

	  Enables support for the Broadcom SPI flash and MSPI controller.

	  Select this option for any one of BRCMSTB, iProc NSP and NS2 SoCs

	  based platforms. This driver works for both SPI master for spi-nor

	  flash device as well as MSPI device.

config SPI_BITBANG

	tristate "Utilities for Bitbanging SPI masters"

	help

obj-$(CONFIG_SPI_BCM53XX)		+= spi-bcm53xx.o

obj-$(CONFIG_SPI_BCM63XX)		+= spi-bcm63xx.o

obj-$(CONFIG_SPI_BCM63XX_HSSPI)		+= spi-bcm63xx-hsspi.o

obj-$(CONFIG_SPI_BCM_QSPI)		+= spi-iproc-qspi.o spi-brcmstb-qspi.o spi-bcm-qspi.o

obj-$(CONFIG_SPI_BFIN5XX)		+= spi-bfin5xx.o

obj-$(CONFIG_SPI_ADI_V3)                += spi-adi-v3.o

obj-$(CONFIG_SPI_BFIN_SPORT)		+= spi-bfin-sport.o