hwmon: (vt8231) Fix multi-line comments (61ba0318) · Commits · e / devices / android_kernel_teracube_2e

drivers/hwmon/vt8231.c

+87 −77

Original line number	Diff line number	Diff line
		/*
		vt8231.c - Part of lm_sensors, Linux kernel modules
		for hardware monitoring

		Copyright (c) 2005 Roger Lucas <vt8231@hiddenengine.co.uk>
		Copyright (c) 2002 Mark D. Studebaker <mdsxyz123@yahoo.com>
		Aaron M. Marsh <amarsh@sdf.lonestar.org>

		This program is free software; you can redistribute it and/or modify
		it under the terms of the GNU General Public License as published by
		the Free Software Foundation; either version 2 of the License, or
		(at your option) any later version.

		This program is distributed in the hope that it will be useful,
		but WITHOUT ANY WARRANTY; without even the implied warranty of
		MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
		GNU General Public License for more details.

		You should have received a copy of the GNU General Public License
		along with this program; if not, write to the Free Software
		Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
		* vt8231.c - Part of lm_sensors, Linux kernel modules
		* for hardware monitoring
		*
		* Copyright (c) 2005 Roger Lucas <vt8231@hiddenengine.co.uk>
		* Copyright (c) 2002 Mark D. Studebaker <mdsxyz123@yahoo.com>
		* Aaron M. Marsh <amarsh@sdf.lonestar.org>
		*
		* This program is free software; you can redistribute it and/or modify
		* it under the terms of the GNU General Public License as published by
		* the Free Software Foundation; either version 2 of the License, or
		* (at your option) any later version.
		*
		* This program is distributed in the hope that it will be useful,
		* but WITHOUT ANY WARRANTY; without even the implied warranty of
		* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
		* GNU General Public License for more details.
		*
		* You should have received a copy of the GNU General Public License
		* along with this program; if not, write to the Free Software
		* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
		*/

		/* Supports VIA VT8231 South Bridge embedded sensors
		/*
		* Supports VIA VT8231 South Bridge embedded sensors
		*/

		#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
		@@ -50,25 +51,26 @@ static struct platform_device *pdev;
		#define VT8231_BASE_REG 0x70
		#define VT8231_ENABLE_REG 0x74

		/* The VT8231 registers

		The reset value for the input channel configuration is used (Reg 0x4A=0x07)
		which sets the selected inputs marked with '*' below if multiple options are
		possible:

		Voltage Mode Temperature Mode
		Sensor Linux Id Linux Id VIA Id
		-------- -------- -------- ------
		CPU Diode N/A temp1 0
		UIC1 in0 temp2 * 1
		UIC2 in1 * temp3 2
		UIC3 in2 * temp4 3
		UIC4 in3 * temp5 4
		UIC5 in4 * temp6 5
		3.3V in5 N/A

		Note that the BIOS may set the configuration register to a different value
		to match the motherboard configuration.
		/*
		* The VT8231 registers
		*
		* The reset value for the input channel configuration is used (Reg 0x4A=0x07)
		* which sets the selected inputs marked with '*' below if multiple options are
		* possible:
		*
		* Voltage Mode Temperature Mode
		* Sensor Linux Id Linux Id VIA Id
		* -------- -------- -------- ------
		* CPU Diode N/A temp1 0
		* UIC1 in0 temp2 * 1
		* UIC2 in1 * temp3 2
		* UIC3 in2 * temp4 3
		* UIC4 in3 * temp5 4
		* UIC5 in4 * temp6 5
		* 3.3V in5 N/A
		*
		* Note that the BIOS may set the configuration register to a different value
		* to match the motherboard configuration.
		*/

		/* fans numbered 0-1 */
		@@ -81,12 +83,13 @@ static const u8 regvolt[] = { 0x21, 0x22, 0x23, 0x24, 0x25, 0x26 };
		static const u8 regvoltmax[] = { 0x3d, 0x2b, 0x2d, 0x2f, 0x31, 0x33 };
		static const u8 regvoltmin[] = { 0x3e, 0x2c, 0x2e, 0x30, 0x32, 0x34 };

		/* Temperatures are numbered 1-6 according to the Linux kernel specification.
		**
		** In the VIA datasheet, however, the temperatures are numbered from zero.
		** Since it is important that this driver can easily be compared to the VIA
		** datasheet, we will use the VIA numbering within this driver and map the
		** kernel sysfs device name to the VIA number in the sysfs callback.
		/*
		* Temperatures are numbered 1-6 according to the Linux kernel specification.
		*
		* In the VIA datasheet, however, the temperatures are numbered from zero.
		* Since it is important that this driver can easily be compared to the VIA
		* datasheet, we will use the VIA numbering within this driver and map the
		* kernel sysfs device name to the VIA number in the sysfs callback.
		*/

		#define VT8231_REG_TEMP_LOW01 0x49
		@@ -108,8 +111,9 @@ static const u8 regtempmin[] = { 0x3a, 0x3e, 0x2c, 0x2e, 0x30, 0x32 };
		#define VT8231_REG_TEMP1_CONFIG 0x4b
		#define VT8231_REG_TEMP2_CONFIG 0x4c

		/* temps 0-5 as numbered in VIA datasheet - see later for mapping to Linux
		** numbering
		/*
		* temps 0-5 as numbered in VIA datasheet - see later for mapping to Linux
		* numbering
		*/
		#define ISTEMP(i, ch_config) ((i) == 0 ? 1 : \
		((ch_config) >> ((i)+1)) & 0x01)
		@@ -119,23 +123,25 @@ static const u8 regtempmin[] = { 0x3a, 0x3e, 0x2c, 0x2e, 0x30, 0x32 };

		#define DIV_FROM_REG(val) (1 << (val))

		/* NB The values returned here are NOT temperatures. The calibration curves
		** for the thermistor curves are board-specific and must go in the
		** sensors.conf file. Temperature sensors are actually ten bits, but the
		** VIA datasheet only considers the 8 MSBs obtained from the regtemp[]
		** register. The temperature value returned should have a magnitude of 3,
		** so we use the VIA scaling as the "true" scaling and use the remaining 2
		** LSBs as fractional precision.
		**
		** All the on-chip hardware temperature comparisons for the alarms are only
		** 8-bits wide, and compare against the 8 MSBs of the temperature. The bits
		** in the registers VT8231_REG_TEMP_LOW01 and VT8231_REG_TEMP_LOW25 are
		** ignored.
		/*
		* NB The values returned here are NOT temperatures. The calibration curves
		* for the thermistor curves are board-specific and must go in the
		* sensors.conf file. Temperature sensors are actually ten bits, but the
		* VIA datasheet only considers the 8 MSBs obtained from the regtemp[]
		* register. The temperature value returned should have a magnitude of 3,
		* so we use the VIA scaling as the "true" scaling and use the remaining 2
		* LSBs as fractional precision.
		*
		* All the on-chip hardware temperature comparisons for the alarms are only
		* 8-bits wide, and compare against the 8 MSBs of the temperature. The bits
		* in the registers VT8231_REG_TEMP_LOW01 and VT8231_REG_TEMP_LOW25 are
		* ignored.
		*/

		/****** FAN RPM CONVERSIONS ******
		** This chip saturates back at 0, not at 255 like many the other chips.
		** So, 0 means 0 RPM
		/*
		**** FAN RPM CONVERSIONS ******
		* This chip saturates back at 0, not at 255 like many the other chips.
		* So, 0 means 0 RPM
		*/
		static inline u8 FAN_TO_REG(long rpm, int div)
		{
		@@ -463,8 +469,9 @@ static ssize_t set_temp_min(struct device dev, struct device_attribute attr,
		return count;
		}

		/* Note that these map the Linux temperature sensor numbering (1-6) to the VIA
		** temperature sensor numbering (0-5)
		/*
		* Note that these map the Linux temperature sensor numbering (1-6) to the VIA
		* temperature sensor numbering (0-5)
		*/
		#define define_temperature_sysfs(offset) \
		static SENSOR_DEVICE_ATTR(temp##offset##_input, S_IRUGO, \
		@@ -1032,13 +1039,16 @@ static int __devinit vt8231_pci_probe(struct pci_dev *dev,
		if (vt8231_device_add(address))
		goto exit_unregister;

		/* Always return failure here. This is to allow other drivers to bind
		/*
		* Always return failure here. This is to allow other drivers to bind
		* to this pci device. We don't really want to have control over the
		* pci device, we only wanted to read as few register values from it.
		*/

		/* We do, however, mark ourselves as using the PCI device to stop it
		getting unloaded. */
		/*
		* We do, however, mark ourselves as using the PCI device to stop it
		* getting unloaded.
		*/
		s_bridge = pci_dev_get(dev);
		return -ENODEV;