Merge "ARM: dts: msm: Enable PMIC-GPIO clients for msm8996 GVM"

	status = "okay";

};

&blsp1_uart2 {

	status = "okay";

};

&pm8994_gpios {

	gpio@c600 { /* GPIO 7 - adv7481 INT3 */

		qcom,mode = <0>;

		qcom,vin-sel = <2>;

		qcom,src-sel = <0>;

		status = "okay";

	};

	gpio@c800 { /* GPIO 9 - Rome 3.3V control */

		qcom,mode = <1>;                /* Digital output */

		qcom,output-type = <0>;         /* MOS logic */

		qcom,invert = <1>;              /* Output high */

		qcom,vin-sel = <0>;             /* VPH_PWR */

		qcom,src-sel = <0>;             /* Constant */

		qcom,out-strength = <1>;        /* High drive strength */

		qcom,master-en = <1>;           /* Enable GPIO */

		status = "okay";

	};

	gpio@c900 { /* GPIO 10 - NFC CLK _REQ*/

		qcom,mode = <0>;

		qcom,vin-sel = <2>;

		qcom,src-sel = <0>;

		qcom,master-en = <1>;

		status = "okay";

	};

	gpio@cd00 { /* GPIO 14 - lcd_bklt_reg_en */

		qcom,mode = <1>;        /* DIGITAL OUT */

		qcom,output-type = <0>;         /* CMOS logic */

		qcom,invert = <1>;      /* output hight initially */

		qcom,vin-sel = <2>;     /* 1.8 */

		qcom,src-sel = <0>;     /* CONSTANT */

		qcom,out-strength = <1>;        /* Low drive strength */

		qcom,master-en = <1>;   /* ENABLE GPIO */

		status = "okay";

	};

	gpio@c100 { /* GPIO 2 */

		qcom,mode = <0>;

		qcom,pull = <0>;

		qcom,vin-sel = <2>;

		qcom,src-sel = <0>;

		status = "okay";

	};

	gpio@c300 { /* GPIO 4 - adv7481 RST */

		qcom,mode = <1>;

		qcom,pull = <0>;

		qcom,vin-sel = <2>;

		qcom,src-sel = <0>;

		status = "okay";

	};

	gpio@c400 { /* GPIO 5 - adv7481 INT1 */

		qcom,mode = <0>;

		qcom,vin-sel = <2>;

		qcom,src-sel = <0>;

		status = "okay";

	};

	gpio@c500 { /* GPIO 6 - adv7481 INT2*/

		qcom,mode = <0>;

		qcom,vin-sel = <2>;

		qcom,src-sel = <0>;

		status = "okay";

	};

	gpio@ca00 { /* GPIO 11 - USB enb1 (otg switch) */

		qcom,mode = <1>;        /* DIGITAL OUT */

		qcom,vin-sel = <2>;     /* 1.8 */

		qcom,src-sel = <0>;     /* GPIO */

		qcom,master-en = <1>;   /* Enable GPIO */

		status = "okay";

	};

	gpio@cc00 { /* GPIO 13 - NTN_RST */

		qcom,mode = <1>; /* DIGITAL OUT */

		qcom,output-type = <0>; /* CMOS logic */

		qcom,pull = <5>;

		qcom,vin-sel = <2>; /* 1.8 */

		qcom,out-strength = <1>;

		qcom,src-sel = <0>; /* GPIO */

		qcom,master-en = <1>; /* Enable GPIO */

		status = "okay";

	};

	gpio@ce00 { /* GPIO 15 */

		qcom,mode = <1>;

		qcom,output-type = <0>;

		qcom,pull = <5>;

		qcom,vin-sel = <2>;

		qcom,out-strength = <1>;

		qcom,src-sel = <2>;

		qcom,master-en = <1>;

		status = "okay";

	};

	gpio@d000 { /* GPIO 17 - USB1 VBUS detect */

		qcom,mode = <0>;        /* Digital Input*/

		qcom,pull = <5>;        /* No pull */

		qcom,vin-sel = <2>;     /* 1.8 V */

		qcom,src-sel = <0>;     /* GPIO */

		qcom,master-en = <1>;   /* Enable GPIO */

		status = "okay";

	};

	gpio@d100 { /* GPIO 18 - Rome Sleep Clock */

		qcom,mode = <1>;                /* Digital output */

		qcom,output-type = <0>;         /* CMOS logic */

		qcom,invert = <0>;              /* Output low initially */

		qcom,vin-sel = <2>;             /* VIN 2 */

		qcom,src-sel = <3>;             /* Function 2 */

		qcom,out-strength = <2>;        /* Medium */

		qcom,master-en = <1>;           /* Enable GPIO */

		status = "okay";

	};

	gpio@d200 { /* GPIO 19 - Rome BT Reset */

		qcom,mode = <1>;                /* Digital output*/

		qcom,pull = <4>;                /* Pulldown 10uA */

		qcom,vin-sel = <2>;             /* VIN2 */

		qcom,src-sel = <0>;             /* GPIO */

		qcom,invert = <0>;              /* Invert */

		qcom,master-en = <1>;           /* Enable GPIO */

		status = "okay";

	};

};