stallion: final cleanup

	- info about RS485 structures and support in the kernel.

specialix.txt

	- info on hardware/driver for specialix IO8+ multiport serial card.

stallion.txt

	- info on using the Stallion multiport serial driver.

sx.txt

	- info on the Specialix SX/SI multiport serial driver.

tty.txt

* NOTE - This is an unmaintained driver.  Lantronix, which bought Stallion

technologies, is not active in driver maintenance, and they have no information

on when or if they will have a 2.6 driver.

James Nelson <james4765@gmail.com> - 12-12-2004

Stallion Multiport Serial Driver Readme

---------------------------------------

Copyright (C) 1994-1999,  Stallion Technologies.

Version:   5.5.1

Date:      28MAR99

1. INTRODUCTION

There are two drivers that work with the different families of Stallion

multiport serial boards. One is for the Stallion smart boards - that is

EasyIO, EasyConnection 8/32 and EasyConnection 8/64-PCI, the other for

the true Stallion intelligent multiport boards - EasyConnection 8/64

(ISA, EISA), EasyConnection/RA-PCI, ONboard and Brumby.

If you are using any of the Stallion intelligent multiport boards (Brumby,

ONboard, EasyConnection 8/64 (ISA, EISA), EasyConnection/RA-PCI) with

Linux you will need to get the driver utility package.  This contains a

firmware loader and the firmware images necessary to make the devices operate.

The Stallion Technologies ftp site, ftp.stallion.com, will always have

the latest version of the driver utility package.

ftp://ftp.stallion.com/drivers/ata5/Linux/ata-linux-550.tar.gz

As of the printing of this document the latest version of the driver

utility package is 5.5.0. If a later version is now available then you

should use the latest version.

If you are using the EasyIO, EasyConnection 8/32 or EasyConnection 8/64-PCI

boards then you don't need this package, although it does have a serial stats

display program.

If you require DIP switch settings, or EISA configuration files, or any

other information related to Stallion boards then have a look at Stallion's

web pages at http://www.stallion.com.

2. INSTALLATION

The drivers can be used as loadable modules or compiled into the kernel.

You can choose which when doing a "config" on the kernel.

All ISA, and EISA boards that you want to use need to be configured into

the driver(s). All PCI boards will be automatically detected when you load

the driver - so they do not need to be entered into the driver(s)

configuration structure. Note that kernel PCI support is required to use PCI

boards.

There are two methods of configuring ISA and EISA boards into the drivers.

If using the driver as a loadable module then the simplest method is to pass

the driver configuration as module arguments. The other method is to modify

the driver source to add configuration lines for each board in use.

If you have pre-built Stallion driver modules then the module argument

configuration method should be used. A lot of Linux distributions come with

pre-built driver modules in /lib/modules/X.Y.Z/misc for the kernel in use.

That makes things pretty simple to get going.

2.1 MODULE DRIVER CONFIGURATION:

The simplest configuration for modules is to use the module load arguments

to configure any ISA or EISA boards. PCI boards are automatically

detected, so do not need any additional configuration at all.

If using EasyIO, EasyConnection 8/32 ISA, or EasyConnection 8/63-PCI

boards then use the "stallion" driver module, Otherwise if you are using

an EasyConnection 8/64 ISA or EISA, EasyConnection/RA-PCI, ONboard,

Brumby or original Stallion board then use the "istallion" driver module.

Typically to load up the smart board driver use:

    modprobe stallion

This will load the EasyIO and EasyConnection 8/32 driver. It will output a

message to say that it loaded and print the driver version number. It will

also print out whether it found the configured boards or not. These messages

may not appear on the console, but typically are always logged to

/var/adm/messages or /var/log/syslog files - depending on how the klogd and

syslogd daemons are setup on your system.

To load the intelligent board driver use:

    modprobe istallion

It will output similar messages to the smart board driver.

If not using an auto-detectable board type (that is a PCI board) then you

will also need to supply command line arguments to the modprobe command

when loading the driver. The general form of the configuration argument is

    board?=<name>[,<ioaddr>[,<addr>][,<irq>]]

where:

    board?  -- specifies the arbitrary board number of this board,

               can be in the range 0 to 3.

    name    -- textual name of this board. The board name is the common

               board name, or any "shortened" version of that. The board

               type number may also be used here.

    ioaddr  -- specifies the I/O address of this board. This argument is

               optional, but should generally be specified.

    addr    -- optional second address argument. Some board types require

               a second I/O address, some require a memory address. The

               exact meaning of this argument depends on the board type.

    irq     -- optional IRQ line used by this board.

Up to 4 board configuration arguments can be specified on the load line.

Here is some examples:

    modprobe stallion board0=easyio,0x2a0,5

This configures an EasyIO board as board 0 at I/O address 0x2a0 and IRQ 5.

    modprobe istallion board3=ec8/64,0x2c0,0xcc000

This configures an EasyConnection 8/64 ISA as board 3 at I/O address 0x2c0 at

memory address 0xcc000.

    modprobe stallion board1=ec8/32-at,0x2a0,0x280,10

This configures an EasyConnection 8/32 ISA board at primary I/O address 0x2a0,

secondary address 0x280 and IRQ 10.

You will probably want to enter this module load and configuration information

into your system startup scripts so that the drivers are loaded and configured

on each system boot. Typically configuration files are put in the

/etc/modprobe.d/ directory.

2.2 STATIC DRIVER CONFIGURATION:

For static driver configuration you need to modify the driver source code.

Entering ISA and EISA boards into the driver(s) configuration structure

involves editing the driver(s) source file. It's pretty easy if you follow

the instructions below. Both drivers can support up to 4 boards. The smart

card driver (the stallion.c driver) supports any combination of EasyIO and

EasyConnection 8/32 boards (up to a total of 4). The intelligent driver

supports any combination of ONboards, Brumbys, Stallions and EasyConnection

8/64 (ISA and EISA) boards (up to a total of 4).

To set up the driver(s) for the boards that you want to use you need to

edit the appropriate driver file and add configuration entries.

If using EasyIO or EasyConnection 8/32 ISA boards,

   In drivers/char/stallion.c:

      - find the definition of the stl_brdconf array (of structures)

        near the top of the file

      - modify this to match the boards you are going to install

	(the comments before this structure should help)

      - save and exit

If using ONboard, Brumby, Stallion or EasyConnection 8/64 (ISA or EISA)

boards,

   In drivers/char/istallion.c:

      - find the definition of the stli_brdconf array (of structures)

        near the top of the file

      - modify this to match the boards you are going to install

	(the comments before this structure should help)

      - save and exit

Once you have set up the board configurations then you are ready to build

the kernel or modules.

When the new kernel is booted, or the loadable module loaded then the

driver will emit some kernel trace messages about whether the configured

boards were detected or not. Depending on how your system logger is set

up these may come out on the console, or just be logged to

/var/adm/messages or /var/log/syslog. You should check the messages to

confirm that all is well.

2.3 SHARING INTERRUPTS

It is possible to share interrupts between multiple EasyIO and

EasyConnection 8/32 boards in an EISA system. To do this you must be using

static driver configuration, modifying the driver source code to add driver

configuration. Then a couple of extra things are required:

1. When entering the board resources into the stallion.c file you need to

   mark the boards as using level triggered interrupts. Do this by replacing

   the "0" entry at field position 6 (the last field) in the board

   configuration structure with a "1". (This is the structure that defines

   the board type, I/O locations, etc. for each board). All boards that are

   sharing an interrupt must be set this way, and each board should have the

   same interrupt number specified here as well. Now build the module or

   kernel as you would normally.

2. When physically installing the boards into the system you must enter

   the system EISA configuration utility. You will need to install the EISA

   configuration files for *all* the EasyIO and EasyConnection 8/32 boards

   that are sharing interrupts. The Stallion EasyIO and EasyConnection 8/32

   EISA configuration files required are supplied by Stallion Technologies

   on the EASY Utilities floppy diskette (usually supplied in the box with

   the board when purchased. If not, you can pick it up from Stallion's FTP

   site, ftp.stallion.com). You will need to edit the board resources to

   choose level triggered interrupts, and make sure to set each board's

   interrupt to the same IRQ number.

You must complete both the above steps for this to work. When you reboot

or load the driver your EasyIO and EasyConnection 8/32 boards will be

sharing interrupts.

2.4 USING HIGH SHARED MEMORY

The EasyConnection 8/64-EI, ONboard and Stallion boards are capable of

using shared memory addresses above the usual 640K - 1Mb range. The ONboard

ISA and the Stallion boards can be programmed to use memory addresses up to

16Mb (the ISA bus addressing limit), and the EasyConnection 8/64-EI and

ONboard/E can be programmed for memory addresses up to 4Gb (the EISA bus

addressing limit).

The higher than 1Mb memory addresses are fully supported by this driver.

Just enter the address as you normally would for a lower than 1Mb address

(in the driver's board configuration structure).

2.5 TROUBLE SHOOTING

If a board is not found by the driver but is actually in the system then the

most likely problem is that the I/O address is wrong. Change the module load

argument for the loadable module form. Or change it in the driver stallion.c

or istallion.c configuration structure and rebuild the kernel or modules, or

change it on the board.

On EasyIO and EasyConnection 8/32 boards the IRQ is software programmable, so

if there is a conflict you may need to change the IRQ used for a board. There

are no interrupts to worry about for ONboard, Brumby or EasyConnection 8/64

(ISA and EISA) boards. The memory region on EasyConnection 8/64 and

ONboard boards is software programmable, but not on the Brumby boards.

3. USING THE DRIVERS

3.1 INTELLIGENT DRIVER OPERATION

The intelligent boards also need to have their "firmware" code downloaded

to them. This is done via a user level application supplied in the driver

utility package called "stlload". Compile this program wherever you dropped

the package files, by typing "make". In its simplest form you can then type

    ./stlload -i cdk.sys

in this directory and that will download board 0 (assuming board 0 is an

EasyConnection 8/64 or EasyConnection/RA board). To download to an

ONboard, Brumby or Stallion do:

    ./stlload -i 2681.sys

Normally you would want all boards to be downloaded as part of the standard

system startup. To achieve this, add one of the lines above into the

/etc/rc.d/rc.S or /etc/rc.d/rc.serial file. To download each board just add

the "-b <brd-number>" option to the line. You will need to download code for

every board. You should probably move the stlload program into a system

directory, such as /usr/sbin. Also, the default location of the cdk.sys image

file in the stlload down-loader is /usr/lib/stallion. Create that directory

and put the cdk.sys and 2681.sys files in it. (It's a convenient place to put

them anyway). As an example your /etc/rc.d/rc.S file might have the

following lines added to it (if you had 3 boards):

    /usr/sbin/stlload -b 0 -i /usr/lib/stallion/cdk.sys

    /usr/sbin/stlload -b 1 -i /usr/lib/stallion/2681.sys

    /usr/sbin/stlload -b 2 -i /usr/lib/stallion/2681.sys

The image files cdk.sys and 2681.sys are specific to the board types. The

cdk.sys will only function correctly on an EasyConnection 8/64 board. Similarly

the 2681.sys image fill only operate on ONboard, Brumby and Stallion boards.

If you load the wrong image file into a board it will fail to start up, and

of course the ports will not be operational!

If you are using the modularized version of the driver you might want to put

the modprobe calls in the startup script as well (before the download lines

obviously).

3.2 USING THE SERIAL PORTS

Once the driver is installed you will need to setup some device nodes to

access the serial ports. The simplest method is to use the /dev/MAKEDEV program.

It will automatically create device entries for Stallion boards. This will

create the normal serial port devices as /dev/ttyE# where# is the port number

starting from 0. A bank of 64 minor device numbers is allocated to each board,

so the first port on the second board is port 64,etc. A set of callout type

devices may also be created. They are created as the devices /dev/cue# where #

is the same as for the ttyE devices.

For the most part the Stallion driver tries to emulate the standard PC system

COM ports and the standard Linux serial driver. The idea is that you should

be able to use Stallion board ports and COM ports interchangeably without

modifying anything but the device name. Anything that doesn't work like that

should be considered a bug in this driver!

If you look at the driver code you will notice that it is fairly closely

based on the Linux serial driver (linux/drivers/char/serial.c). This is

intentional, obviously this is the easiest way to emulate its behavior!

Since this driver tries to emulate the standard serial ports as much as

possible, most system utilities should work as they do for the standard

COM ports. Most importantly "stty" works as expected and "setserial" can

also be used (excepting the ability to auto-configure the I/O and IRQ

addresses of boards). Higher baud rates are supported in the usual fashion

through setserial or using the CBAUDEX extensions. Note that the EasyIO and

EasyConnection (all types) support at least 57600 and 115200 baud. The newer

EasyConnection XP modules and new EasyIO boards support 230400 and 460800

baud as well. The older boards including ONboard and Brumby support a

maximum baud rate of 38400.

If you are unfamiliar with how to use serial ports, then get the Serial-HOWTO

by Greg Hankins. It will explain everything you need to know!

4. NOTES

You can use both drivers at once if you have a mix of board types installed

in a system. However to do this you will need to change the major numbers

used by one of the drivers. Currently both drivers use major numbers 24, 25

and 28 for their devices. Change one driver to use some other major numbers,

and then modify the mkdevnods script to make device nodes based on those new

major numbers. For example, you could change the istallion.c driver to use

major numbers 60, 61 and 62. You will also need to create device nodes with

different names for the ports, for example ttyF# and cuf#.

The original Stallion board is no longer supported by Stallion Technologies.

Although it is known to work with the istallion driver.

Finding a free physical memory address range can be a problem. The older

boards like the Stallion and ONboard need large areas (64K or even 128K), so

they can be very difficult to get into a system. If you have 16 Mb of RAM

then you have no choice but to put them somewhere in the 640K -> 1Mb range.

ONboards require 64K, so typically 0xd0000 is good, or 0xe0000 on some

systems. If you have an original Stallion board, "V4.0" or Rev.O, then you

need a 64K memory address space, so again 0xd0000 and 0xe0000 are good.

Older Stallion boards are a much bigger problem. They need 128K of address

space and must be on a 128K boundary. If you don't have a VGA card then

0xc0000 might be usable - there is really no other place you can put them

below 1Mb.

Both the ONboard and old Stallion boards can use higher memory addresses as

well, but you must have less than 16Mb of RAM to be able to use them. Usual

high memory addresses used include 0xec0000 and 0xf00000.

The Brumby boards only require 16Kb of address space, so you can usually

squeeze them in somewhere. Common addresses are 0xc8000, 0xcc000, or in

the 0xd0000 range. EasyConnection 8/64 boards are even better, they only

require 4Kb of address space, again usually 0xc8000, 0xcc000 or 0xd0000

are good.

If you are using an EasyConnection 8/64-EI or ONboard/E then usually the

0xd0000 or 0xe0000 ranges are the best options below 1Mb. If neither of

them can be used then the high memory support to use the really high address

ranges is the best option. Typically the 2Gb range is convenient for them,

and gets them well out of the way.

The ports of the EasyIO-8M board do not have DCD or DTR signals. So these

ports cannot be used as real modem devices. Generally, when using these

ports you should only use the cueX devices.

The driver utility package contains a couple of very useful programs. One 

is a serial port statistics collection and display program - very handy

for solving serial port problems. The other is an extended option setting

program that works with the intelligent boards.

5. DISCLAIMER

The information contained in this document is believed to be accurate and

reliable. However, no responsibility is assumed by Stallion Technologies

Pty. Ltd. for its use, nor any infringements of patents or other rights

of third parties resulting from its use. Stallion Technologies reserves

the right to modify the design of its products and will endeavour to change

the information in manuals and accompanying documentation accordingly.

	  kind of kernel debugging operations.

	  When in doubt, say "N".

config STALDRV

	bool "Stallion multiport serial support"

	depends on SERIAL_NONSTANDARD

	help

	  Stallion cards give you many serial ports.  You would need something

	  like this to connect more than two modems to your Linux box, for

	  instance in order to become a dial-in server.  If you say Y here,

	  you will be asked for your specific card model in the next

	  questions.  Make sure to read <file:Documentation/serial/stallion.txt>

	  in this case.  If you have never heard about all this, it's safe to

	  say N.

config SGI_SNSC

	bool "SGI Altix system controller communication support"

	depends on (IA64_SGI_SN2 || IA64_GENERIC)

	  here are those that are setting up dedicated Ethernet WWW/FTP

	  servers, or users that have one of the various bus mice instead of a

	  serial mouse and don't intend to use their machine's standard serial

	  port for anything.  (Note that the Cyclades and Stallion multi

	  serial port drivers do not need this driver built in for them to

	  work.)

	  port for anything.  (Note that the Cyclades multi serial port driver

	  does not need this driver built in for it to work.)

	  To compile this driver as a module, choose M here: the

	  module will be called 8250.