Promotion of kernel.lnx.4.4-160802. (da92b44b) · Commits · e / devices / android_kernel_sony_msm8998

Documentation/devicetree/bindings/fb/mdss-dp.txt

+19 −0

Original line number	Diff line number	Diff line
		@@ -24,6 +24,9 @@ Required properties
		- clocks: List of Phandles for clock device nodes
		needed by the device.
		- clock-names: List of clock names needed by the device.
		- qcom,aux-en-gpio: Specifies the aux-channel enable gpio.
		- qcom,aux-sel-gpio: Specifies the aux-channel select gpio.
		- qcom,usbplug-cc-gpio: Specifies the usbplug orientation gpio.

		Optional properties:
		- qcom,<type>-supply-entries: A node that lists the elements of the supply used by the
		@@ -42,6 +45,12 @@ Optional properties:
		-- qcom,supply-post-on-sleep: time to sleep (ms) after turning on
		-- qcom,supply-pre-off-sleep: time to sleep (ms) before turning off
		-- qcom,supply-post-off-sleep: time to sleep (ms) after turning off
		- qcom,hpd-gpio: Specifies the HPD gpio.
		- pinctrl-names: List of names to assign mdss pin states defined in pinctrl device node
		Refer to pinctrl-bindings.txt
		- pinctrl-<0..n>: Lists phandles each pointing to the pin configuration node within a pin
		controller. These pin configurations are installed in the pinctrl
		device node. Refer to pinctrl-bindings.txt

		Example:
		mdss_dp_ctrl: qcom,dp_ctrl@c990000 {
		@@ -115,5 +124,15 @@ Example:
		qcom,supply-disable-load = <32>;
		};
		};

		pinctrl-names = "mdss_dp_active", "mdss_dp_sleep";
		pinctrl-0 = <&mdss_dp_aux_active &mdss_dp_usbplug_cc_active
		&mdss_dp_hpd_active>;
		pinctrl-1 = <&mdss_dp_aux_suspend &mdss_dp_usbplug_cc_suspend
		&mdss_dp_hpd_suspend>;
		qcom,aux-en-gpio = <&tlmm 77 0>;
		qcom,aux-sel-gpio = <&tlmm 78 0>;
		qcom,usbplug-cc-gpio = <&tlmm 38 0>;
		qcom,hpd-gpio = <&tlmm 34 0>;
		};

Documentation/devicetree/bindings/input/touchscreen/it7258_ts_i2c.txt

0 → 100644

+47 −0

Original line number	Diff line number	Diff line
		ITE Tech. touch controller

		The ITE Tech. touch controller is connected to host processor
		via i2c. The controller generates interrupts when the user
		touches the panel. The host controller is expected to read
		the touch coordinates over i2c and pass the coordinates to
		the rest of the system.

		Required properties:

		- compatible : should be "ite,it7260_ts"
		- reg : i2c slave address of the device
		- interrupt-parent : parent of interrupt
		- interrupts : touch sample interrupt to indicate presence or release
		of fingers on the panel.
		- ite,irq-gpio : irq gpio which is to provide interrupts to host,
		same as "interrupts" node. It will also
		contain active low or active high information.
		- ite,reset-gpio : reset gpio to control the reset of chip

		Optional properties:
		- avdd-supply : Analog power supply needed to power device
		- vdd-supply : Power source required to pull up i2c bus
		- ite,wakeup : boolean, use this to support touch-to-wake feature.
		- ite,palm-detect-en : boolean, use this to send palm-detect-keycode when
		palm is detected.

		Required properties palm-detect-en feature:
		- ite,palm-detect-keycode : The keycode that is required to be sent when
		palm is detected by the ITE tech driver.

		Example:
		i2c@f9927000 {
		it7260@46 {
		compatible = "ite,it7260_ts";
		reg = <0x46>;
		interrupt-parent = <&msmgpio>;
		interrupts = <17 0x2>;
		avdd-supply = <&pm8226_l19>;
		vdd-supply = <&pm8226_lvs1>;
		ite,reset-gpio = <&msmgpio 16 0x00>;
		ite,irq-gpio = <&msmgpio 17 0x2008>;
		ite,wakeup;
		ite,palm-detect-en;
		ite,palm-detect-keycode = <142>;
		};
		};

Documentation/devicetree/bindings/leds/leds-qpnp-flash-v2.txt

+34 −2

Original line number	Diff line number	Diff line
		@@ -13,9 +13,25 @@ Required properties:
		- reg : Base address and size for flash LED modules

		Optional properties:
		- interrupts : Specifies the interrupts associated with flash-led.
		- interrupt-names : Specify the interrupt names associated with interrupts.
		- qcom,hdrm-auto-mode : Boolean type to select headroom auto mode enabled or not
		- qcom,isc-delay : Integer type to specify short circuit delay. Valid values are 32, 64,
		128, 192. Unit is us.
		- qcom,isc-delay-us : Integer type to specify short circuit delay. Valid values are 32, 64,
		128, 192. Unit is uS.
		- qcom,warmup-delay-us : Integer type to specify warm up delay. Valid values are 32, 64,
		128, 192. Unit is uS.
		- qcom,short-circuit-det : Boolean property which enables short circuit fault detection.
		- qcom,open-circuit-det : Boolean property which enables open circuit fault detection.
		- qcom,vph-droop-det : Boolean property which enables VPH droop detection.
		- qcom,vph-droop-hys-mv : Integer property to specify VPH droop hysteresis. It is only used if
		qcom,vph-droop-det is specified. Valid values are 0, 25, 50 and 75.
		Unit is mV.
		- qcom,vph-droop-thresh-mv : Integer property to specify VPH droop threshold. It is only used if
		qcom,vph-droop-det is specified. Valid values are
		2500 to 3200 with step size of 100. Unit is mV.
		- qcom,vph-droop-debounce-us : Integer property to specify VPH droop debounce time. It is only used
		if qcom,vph-droop-det is specified. Valid values are 0, 8, 16 and 26.
		Unit is uS.
		- qcom,hw-strobe-option : Integer type to specify hardware strobe option. Based on the specified
		value, additional GPIO configuration may be required to provide strobing
		support. Supported values are:
		@@ -93,6 +109,22 @@ Example:
		status = "okay";
		reg = <0xd300 0x100>;
		label = "flash";
		interrupts = <0x3 0xd3 0x0 IRQ_TYPE_EDGE_BOTH>,
		<0x3 0xd3 0x1 IRQ_TYPE_EDGE_BOTH>,
		<0x3 0xd3 0x2 IRQ_TYPE_EDGE_BOTH>,
		<0x3 0xd3 0x3 IRQ_TYPE_EDGE_BOTH>,
		<0x3 0xd3 0x4 IRQ_TYPE_EDGE_BOTH>,
		<0x3 0xd3 0x5 IRQ_TYPE_EDGE_BOTH>,
		<0x3 0xd3 0x6 IRQ_TYPE_EDGE_BOTH>,
		<0x3 0xd3 0x7 IRQ_TYPE_EDGE_BOTH>;
		interrupt-names = "led-fault-irq",
		"mitigation-irq",
		"flash-timer-exp-irq",
		"all-ramp-down-done-irq",
		"all-ramp-up-done-irq",
		"led3-ramp-up-done-irq",
		"led2-ramp-up-done-irq",
		"led1-ramp-up-done-irq";

		qcom,hdrm-auto-mode;
		qcom,isc-delay = <192>;

Documentation/devicetree/bindings/media/video/msm-vidc.txt

+2 −0

Original line number	Diff line number	Diff line
		@@ -130,6 +130,8 @@ value is typically max(latencies of every cluster at all power levels) + 1
		- qcom,max-secure-instances = An int containing max number of concurrent secure
		instances supported, accounting for venus and system wide limitations like
		memory, performance etc.
		- qcom,debug-timeout = A bool indicating that FW errors such as SYS_ERROR,
		SESSION_ERROR and timeouts will be treated as Fatal.

		[Second level nodes]
		Context Banks

Documentation/devicetree/bindings/platform/msm/ipa.txt

+7 −1

Original line number	Diff line number	Diff line
		@@ -119,6 +119,9 @@ IPA SMMU sub nodes

		- qcom,iova-mapping: specifies the start address and size of iova space.

		- qcom,additional-mapping: specifies any addtional mapping needed for this
		context bank. The format is <iova pa size>

		IPA SMP2P sub nodes

		-compatible: "qcom,smp2pgpio-map-ipa-1-out" - represents the out gpio from
		@@ -195,7 +198,10 @@ qcom,ipa@fd4c0000 {
		ipa_smmu_ap: ipa_smmu_ap {
		compatible = "qcom,ipa-smmu-ap-cb";
		iommus = <&anoc2_smmu 0x30>;
		qcom,iova-mapping = <0x10000000 0x40000000>;
		qcom,iova-mapping = <0x20000000 0x40000000>;
		qcom,additional-mapping =
		/* modem tables in IMEM */
		<0x146BD000 0x146BD000 0x2000>;
		};

		ipa_smmu_wlan: ipa_smmu_wlan {