Merge e50c0007 on remote branch

Required properties:

Optional properties:

- contiguous-region: reserved memory for HDMI and DSI buffer.

- qcom,sde-plane-id-map: plane id mapping for virtual plane.

- qcom,sde-plane-id: each virtual plane mapping node.

- reg: reg property.

Example:

&mdss_mdp {

	contiguous-region = <&cont_splash_mem &cont_splash_mem_hdmi>;

	qcom,sde-plane-id-map {

		qcom,sde-plane-id@0 {

			reg = <0x0>;

				rendering thread is running on masked CPUs.

				Bit 0 is for CPU-0, bit 1 is for CPU-1...

- qcom,l2pc-update-queue:

				Disables L2PC on masked CPUs at queue time when it's true.

- qcom,snapshot-size:

				Specify the size of snapshot in bytes. This will override

				snapshot size defined in the driver code.

- qcom,gpio-vdig : should contain index to gpio used by sensors digital vreg enable

- qcom,gpio-vaf : should contain index to gpio used by sensors af vreg enable

- qcom,gpio-af-pwdm : should contain index to gpio used by sensors af pwdm_n

- qcom,gpio-custom1 : should contain index to gpio used by sensors specific to usecase

- qcom,gpio-custom2 : should contain index to gpio used by sensors specific to usecase

- qcom,gpio-custom3 : should contain index to gpio used by sensors specific to usecase

- qcom,gpio-req-tbl-num : should contain index to gpios specific to this sensor

- qcom,gpio-req-tbl-flags : should contain direction of gpios present in

    qcom,gpio-req-tbl-num property (in the same order)

    and assign for each endpoint.

  - qcom,ep-latency: The time (unit: ms) to wait for the PCIe endpoint to become

    stable after power on, before de-assert the PERST to the endpoint.

  - qcom,switch-latency: The time (unit: ms) to wait for the PCIe endpoint's link

    training with switch downstream port after the link between switch upstream

    port and RC is up.

  - qcom,wr-halt-size: With base 2, this exponent determines the size of the

    data that PCIe core will halt on for each write transaction.

  - qcom,cpl-timeout: Completion timeout value. This value specifies the time range

		qcom,smmu-exist;

		qcom,smmu-sid-base = <0x1480>;

		qcom,ep-latency = <100>;

		qcom,switch-latency = <100>;

		qcom,wr-halt-size = <0xa>; /* 1KB */

		qcom,cpl-timeout = <0x2>;

             "riva_ccu_base", "pronto_a2xb_base", "pronto_ccpu_base",

             "pronto_saw2_base", "wlan_tx_phy_aborts","wlan_brdg_err_source",

             "wlan_tx_status", "alarms_txctl", "alarms_tactl",

             "pronto_mcu_base".

             "pronto_mcu_base", "pronto_qfuse".

- interupts: Pronto to Apps interrupts for tx done and rx pending.

- qcom,pronto-vddmx-supply: regulator to supply pronto pll.

- qcom,pronto-vddcx-supply: voltage corner regulator to supply WLAN/BT/FM

- qcom,wcnss-vadc: VADC handle for battery voltage notification APIs.

- pinctrl-<n> : Pinctrl states as described in bindings/pinctrl/pinctrl-bindings.txt

- pinctrl-names : Names corresponding to the numbered pinctrl states

- clocks: from common clock binding: handle to xo and rf_clk clocks.

- clocks: from common clock binding: handle to xo, rf_clk and wcnss snoc clocks.

- clock-names: Names of all the clocks that are accessed by the subsystem

- qcom,vdd-voltage-level: This property represents (nominal, min, max) voltage

for iris and pronto regulators in milli-volts.

Optional properties:

- qcom,has-autodetect-xo: boolean flag to determine whether Iris XO auto detect

should be performed during boot up.

- qcom,snoc-wcnss-clock-freq: indicates the wcnss snoc clock frequency in Hz.

If wcnss_snoc clock is specified in the list of clocks, this property needs

to be set to make it functional.

- qcom,wlan-rx-buff-count: WLAN RX buffer count is a configurable value,

using a smaller count for this buffer will reduce the memory usage.

- qcom,is-pronto-v3: boolean flag to determine the pronto hardware version

in use. subsequently correct workqueue will be used by DXE engine to push frames

in TX data path.

- qcom,is-dual-band-disable: boolean flag to determine the WLAN dual band

                             capability.

- qcom,is-pronto-vadc: boolean flag to determine Battery voltage feature

support for pronto hardware.

- qcom,wcnss-pm : <Core rail LDO#, PA rail LDO#, XO settling time,

to use for VBATT feature.

- qcom,has-a2xb-split-reg: boolean flag to determine A2xb split timeout limit

register is available or not.

- qcom,wcn-external-gpio-support: boolean flag to determine 3.3v gpio support

for pronto hardware for a target.

Example:

        gpios = <&msmgpio 36 0>, <&msmgpio 37 0>, <&msmgpio 38 0>,

                <&msmgpio 39 0>, <&msmgpio 40 0>;

        qcom,wcn-external-gpio-support;

        qcom,has-48mhz-xo;

        qcom,is-pronto-vt;

        qcom,wlan-rx-buff-count = <512>;

        clocks = <&clock_rpm clk_xo_wlan_clk>,

                   <&clock_rpm clk_rf_clk2>,

                   <&clock_debug clk_gcc_debug_mux>,

                   <&clock_gcc clk_wcnss_m_clk>;

        clock-names = "xo", "rf_clk", "measure", "wcnss_debug";

                   <&clock_gcc clk_wcnss_m_clk>,

		   <&clock_gcc clk_snoc_wcnss_a_clk>;

        clock-names = "xo", "rf_clk", "measure", "wcnss_debug",

			"snoc_wcnss";

	qcom,snoc-wcnss-clock-freq = <200000000>;

	qcom,wcnss-pm = <11 21 1200 1 1 6>;

    };