Revert "drm/msm/dsi-staging: add hardware driver for dsi controller" (17cf4870) · Commits · e / devices / android_kernel_sony_msm8998

drivers/gpu/drm/msm/dsi-staging/dsi_ctrl_hw.h

deleted100644 → 0

+0 −558

Original line number	Diff line number	Diff line
		/*
		* Copyright (c) 2015-2016, The Linux Foundation. All rights reserved.
		*
		* This program is free software; you can redistribute it and/or modify
		* it under the terms of the GNU General Public License version 2 and
		* only version 2 as published by the Free Software Foundation.
		*
		* This program is distributed in the hope that it will be useful,
		* but WITHOUT ANY WARRANTY; without even the implied warranty of
		* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
		* GNU General Public License for more details.
		*
		*/

		#ifndef _DSI_CTRL_HW_H_
		#define _DSI_CTRL_HW_H_

		#include <linux/kernel.h>
		#include <linux/types.h>
		#include <linux/bitops.h>
		#include <linux/bitmap.h>

		#include "dsi_defs.h"

		/**
		* Modifier flag for command transmission. If this flag is set, command
		* information is programmed to hardware and transmission is not triggered.
		* Caller should call the trigger_command_dma() to start the transmission. This
		* flag is valed for kickoff_command() and kickoff_fifo_command() operations.
		*/
		#define DSI_CTRL_HW_CMD_WAIT_FOR_TRIGGER 0x1

		/**
		* enum dsi_ctrl_version - version of the dsi host controller
		* @DSI_CTRL_VERSION_UNKNOWN: Unknown controller version
		* @DSI_CTRL_VERSION_1_4: DSI host v1.4 controller
		* @DSI_CTRL_VERSION_2_0: DSI host v2.0 controller
		* @DSI_CTRL_VERSION_MAX: max version
		*/
		enum dsi_ctrl_version {
		DSI_CTRL_VERSION_UNKNOWN,
		DSI_CTRL_VERSION_1_4,
		DSI_CTRL_VERSION_2_0,
		DSI_CTRL_VERSION_MAX
		};

		/**
		* enum dsi_ctrl_hw_features - features supported by dsi host controller
		* @DSI_CTRL_VIDEO_TPG: Test pattern support for video mode.
		* @DSI_CTRL_CMD_TPG: Test pattern support for command mode.
		* @DSI_CTRL_VARIABLE_REFRESH_RATE: variable panel timing
		* @DSI_CTRL_DYNAMIC_REFRESH: variable pixel clock rate
		* @DSI_CTRL_NULL_PACKET_INSERTION: NULL packet insertion
		* @DSI_CTRL_DESKEW_CALIB: Deskew calibration support
		* @DSI_CTRL_DPHY: Controller support for DPHY
		* @DSI_CTRL_CPHY: Controller support for CPHY
		* @DSI_CTRL_MAX_FEATURES:
		*/
		enum dsi_ctrl_hw_features {
		DSI_CTRL_VIDEO_TPG,
		DSI_CTRL_CMD_TPG,
		DSI_CTRL_VARIABLE_REFRESH_RATE,
		DSI_CTRL_DYNAMIC_REFRESH,
		DSI_CTRL_NULL_PACKET_INSERTION,
		DSI_CTRL_DESKEW_CALIB,
		DSI_CTRL_DPHY,
		DSI_CTRL_CPHY,
		DSI_CTRL_MAX_FEATURES
		};

		/**
		* enum dsi_test_pattern - test pattern type
		* @DSI_TEST_PATTERN_FIXED: Test pattern is fixed, based on init value.
		* @DSI_TEST_PATTERN_INC: Incremental test pattern, base on init value.
		* @DSI_TEST_PATTERN_POLY: Pattern generated from polynomial and init val.
		* @DSI_TEST_PATTERN_MAX:
		*/
		enum dsi_test_pattern {
		DSI_TEST_PATTERN_FIXED = 0,
		DSI_TEST_PATTERN_INC,
		DSI_TEST_PATTERN_POLY,
		DSI_TEST_PATTERN_MAX
		};

		/**
		* enum dsi_status_int_type - status interrupts generated by DSI controller
		* @DSI_CMD_MODE_DMA_DONE: Command mode DMA packets are sent out.
		* @DSI_CMD_STREAM0_FRAME_DONE: A frame of command mode stream0 is sent out.
		* @DSI_CMD_STREAM1_FRAME_DONE: A frame of command mode stream1 is sent out.
		* @DSI_CMD_STREAM2_FRAME_DONE: A frame of command mode stream2 is sent out.
		* @DSI_VIDEO_MODE_FRAME_DONE: A frame of video mode stream is sent out.
		* @DSI_BTA_DONE: A BTA is completed.
		* @DSI_CMD_FRAME_DONE: A frame of selected command mode stream is
		* sent out by MDP.
		* @DSI_DYN_REFRESH_DONE: The dynamic refresh operation has completed.
		* @DSI_DESKEW_DONE: The deskew calibration operation has completed
		* @DSI_DYN_BLANK_DMA_DONE: The dynamic blankin DMA operation has
		* completed.
		*/
		enum dsi_status_int_type {
		DSI_CMD_MODE_DMA_DONE = BIT(0),
		DSI_CMD_STREAM0_FRAME_DONE = BIT(1),
		DSI_CMD_STREAM1_FRAME_DONE = BIT(2),
		DSI_CMD_STREAM2_FRAME_DONE = BIT(3),
		DSI_VIDEO_MODE_FRAME_DONE = BIT(4),
		DSI_BTA_DONE = BIT(5),
		DSI_CMD_FRAME_DONE = BIT(6),
		DSI_DYN_REFRESH_DONE = BIT(7),
		DSI_DESKEW_DONE = BIT(8),
		DSI_DYN_BLANK_DMA_DONE = BIT(9)
		};

		/**
		* enum dsi_error_int_type - error interrupts generated by DSI controller
		* @DSI_RDBK_SINGLE_ECC_ERR: Single bit ECC error in read packet.
		* @DSI_RDBK_MULTI_ECC_ERR: Multi bit ECC error in read packet.
		* @DSI_RDBK_CRC_ERR: CRC error in read packet.
		* @DSI_RDBK_INCOMPLETE_PKT: Incomplete read packet.
		* @DSI_PERIPH_ERROR_PKT: Error packet returned from peripheral,
		* @DSI_LP_RX_TIMEOUT: Low power reverse transmission timeout.
		* @DSI_HS_TX_TIMEOUT: High speed forward transmission timeout.
		* @DSI_BTA_TIMEOUT: BTA timeout.
		* @DSI_PLL_UNLOCK: PLL has unlocked.
		* @DSI_DLN0_ESC_ENTRY_ERR: Incorrect LP Rx escape entry.
		* @DSI_DLN0_ESC_SYNC_ERR: LP Rx data is not byte aligned.
		* @DSI_DLN0_LP_CONTROL_ERR: Incorrect LP Rx state sequence.
		* @DSI_PENDING_HS_TX_TIMEOUT: Pending High-speed transfer timeout.
		* @DSI_INTERLEAVE_OP_CONTENTION: Interleave operation contention.
		* @DSI_CMD_DMA_FIFO_UNDERFLOW: Command mode DMA FIFO underflow.
		* @DSI_CMD_MDP_FIFO_UNDERFLOW: Command MDP FIFO underflow (failed to
		* receive one complete line from MDP).
		* @DSI_DLN0_HS_FIFO_OVERFLOW: High speed FIFO for data lane 0 overflows.
		* @DSI_DLN1_HS_FIFO_OVERFLOW: High speed FIFO for data lane 1 overflows.
		* @DSI_DLN2_HS_FIFO_OVERFLOW: High speed FIFO for data lane 2 overflows.
		* @DSI_DLN3_HS_FIFO_OVERFLOW: High speed FIFO for data lane 3 overflows.
		* @DSI_DLN0_HS_FIFO_UNDERFLOW: High speed FIFO for data lane 0 underflows.
		* @DSI_DLN1_HS_FIFO_UNDERFLOW: High speed FIFO for data lane 1 underflows.
		* @DSI_DLN2_HS_FIFO_UNDERFLOW: High speed FIFO for data lane 2 underflows.
		* @DSI_DLN3_HS_FIFO_UNDERFLOW: High speed FIFO for data lane 3 undeflows.
		* @DSI_DLN0_LP0_CONTENTION: PHY level contention while lane 0 is low.
		* @DSI_DLN1_LP0_CONTENTION: PHY level contention while lane 1 is low.
		* @DSI_DLN2_LP0_CONTENTION: PHY level contention while lane 2 is low.
		* @DSI_DLN3_LP0_CONTENTION: PHY level contention while lane 3 is low.
		* @DSI_DLN0_LP1_CONTENTION: PHY level contention while lane 0 is high.
		* @DSI_DLN1_LP1_CONTENTION: PHY level contention while lane 1 is high.
		* @DSI_DLN2_LP1_CONTENTION: PHY level contention while lane 2 is high.
		* @DSI_DLN3_LP1_CONTENTION: PHY level contention while lane 3 is high.
		*/
		enum dsi_error_int_type {
		DSI_RDBK_SINGLE_ECC_ERR = BIT(0),
		DSI_RDBK_MULTI_ECC_ERR = BIT(1),
		DSI_RDBK_CRC_ERR = BIT(2),
		DSI_RDBK_INCOMPLETE_PKT = BIT(3),
		DSI_PERIPH_ERROR_PKT = BIT(4),
		DSI_LP_RX_TIMEOUT = BIT(5),
		DSI_HS_TX_TIMEOUT = BIT(6),
		DSI_BTA_TIMEOUT = BIT(7),
		DSI_PLL_UNLOCK = BIT(8),
		DSI_DLN0_ESC_ENTRY_ERR = BIT(9),
		DSI_DLN0_ESC_SYNC_ERR = BIT(10),
		DSI_DLN0_LP_CONTROL_ERR = BIT(11),
		DSI_PENDING_HS_TX_TIMEOUT = BIT(12),
		DSI_INTERLEAVE_OP_CONTENTION = BIT(13),
		DSI_CMD_DMA_FIFO_UNDERFLOW = BIT(14),
		DSI_CMD_MDP_FIFO_UNDERFLOW = BIT(15),
		DSI_DLN0_HS_FIFO_OVERFLOW = BIT(16),
		DSI_DLN1_HS_FIFO_OVERFLOW = BIT(17),
		DSI_DLN2_HS_FIFO_OVERFLOW = BIT(18),
		DSI_DLN3_HS_FIFO_OVERFLOW = BIT(19),
		DSI_DLN0_HS_FIFO_UNDERFLOW = BIT(20),
		DSI_DLN1_HS_FIFO_UNDERFLOW = BIT(21),
		DSI_DLN2_HS_FIFO_UNDERFLOW = BIT(22),
		DSI_DLN3_HS_FIFO_UNDERFLOW = BIT(23),
		DSI_DLN0_LP0_CONTENTION = BIT(24),
		DSI_DLN1_LP0_CONTENTION = BIT(25),
		DSI_DLN2_LP0_CONTENTION = BIT(26),
		DSI_DLN3_LP0_CONTENTION = BIT(27),
		DSI_DLN0_LP1_CONTENTION = BIT(28),
		DSI_DLN1_LP1_CONTENTION = BIT(29),
		DSI_DLN2_LP1_CONTENTION = BIT(30),
		DSI_DLN3_LP1_CONTENTION = BIT(31),
		};

		/**
		* struct dsi_ctrl_cmd_dma_info - command buffer information
		* @offset: IOMMU VA for command buffer address.
		* @length: Length of the command buffer.
		* @en_broadcast: Enable broadcast mode if set to true.
		* @is_master: Is master in broadcast mode.
		* @use_lpm: Use low power mode for command transmission.
		*/
		struct dsi_ctrl_cmd_dma_info {
		u32 offset;
		u32 length;
		bool en_broadcast;
		bool is_master;
		bool use_lpm;
		};

		/**
		* struct dsi_ctrl_cmd_dma_fifo_info - command payload tp be sent using FIFO
		* @command: VA for command buffer.
		* @size: Size of the command buffer.
		* @en_broadcast: Enable broadcast mode if set to true.
		* @is_master: Is master in broadcast mode.
		* @use_lpm: Use low power mode for command transmission.
		*/
		struct dsi_ctrl_cmd_dma_fifo_info {
		u32 *command;
		u32 size;
		bool en_broadcast;
		bool is_master;
		bool use_lpm;
		};

		struct dsi_ctrl_hw;

		/**
		* struct dsi_ctrl_hw_ops - operations supported by dsi host hardware
		*/
		struct dsi_ctrl_hw_ops {

		/**
		* host_setup() - Setup DSI host configuration
		* @ctrl: Pointer to controller host hardware.
		* @config: Configuration for DSI host controller
		*/
		void (host_setup)(struct dsi_ctrl_hw ctrl,
		struct dsi_host_common_cfg *config);

		/**
		* video_engine_en() - enable DSI video engine
		* @ctrl: Pointer to controller host hardware.
		* @on: Enable/disabel video engine.
		*/
		void (video_engine_en)(struct dsi_ctrl_hw ctrl, bool on);

		/**
		* video_engine_setup() - Setup dsi host controller for video mode
		* @ctrl: Pointer to controller host hardware.
		* @common_cfg: Common configuration parameters.
		* @cfg: Video mode configuration.
		*
		* Set up DSI video engine with a specific configuration. Controller and
		* video engine are not enabled as part of this function.
		*/
		void (video_engine_setup)(struct dsi_ctrl_hw ctrl,
		struct dsi_host_common_cfg *common_cfg,
		struct dsi_video_engine_cfg *cfg);

		/**
		* set_video_timing() - set up the timing for video frame
		* @ctrl: Pointer to controller host hardware.
		* @mode: Video mode information.
		*
		* Set up the video timing parameters for the DSI video mode operation.
		*/
		void (set_video_timing)(struct dsi_ctrl_hw ctrl,
		struct dsi_mode_info *mode);

		/**
		* cmd_engine_setup() - setup dsi host controller for command mode
		* @ctrl: Pointer to the controller host hardware.
		* @common_cfg: Common configuration parameters.
		* @cfg: Command mode configuration.
		*
		* Setup DSI CMD engine with a specific configuration. Controller and
		* command engine are not enabled as part of this function.
		*/
		void (cmd_engine_setup)(struct dsi_ctrl_hw ctrl,
		struct dsi_host_common_cfg *common_cfg,
		struct dsi_cmd_engine_cfg *cfg);

		/**
		* ctrl_en() - enable DSI controller engine
		* @ctrl: Pointer to the controller host hardware.
		* @on: turn on/off the DSI controller engine.
		*/
		void (ctrl_en)(struct dsi_ctrl_hw ctrl, bool on);

		/**
		* cmd_engine_en() - enable DSI controller command engine
		* @ctrl: Pointer to the controller host hardware.
		* @on: Turn on/off the DSI command engine.
		*/
		void (cmd_engine_en)(struct dsi_ctrl_hw ctrl, bool on);

		/**
		* phy_sw_reset() - perform a soft reset on the PHY.
		* @ctrl: Pointer to the controller host hardware.
		*/
		void (phy_sw_reset)(struct dsi_ctrl_hw ctrl);

		/**
		* soft_reset() - perform a soft reset on DSI controller
		* @ctrl: Pointer to the controller host hardware.
		*
		* The video, command and controller engines will be disable before the
		* reset is triggered. These engines will not be enabled after the reset
		* is complete. Caller must re-enable the engines.
		*
		* If the reset is done while MDP timing engine is turned on, the video
		* enigne should be re-enabled only during the vertical blanking time.
		*/
		void (soft_reset)(struct dsi_ctrl_hw ctrl);

		/**
		* setup_lane_map() - setup mapping between logical and physical lanes
		* @ctrl: Pointer to the controller host hardware.
		* @lane_map: Structure defining the mapping between DSI logical
		* lanes and physical lanes.
		*/
		void (setup_lane_map)(struct dsi_ctrl_hw ctrl,
		struct dsi_lane_mapping *lane_map);

		/**
		* kickoff_command() - transmits commands stored in memory
		* @ctrl: Pointer to the controller host hardware.
		* @cmd: Command information.
		* @flags: Modifiers for command transmission.
		*
		* The controller hardware is programmed with address and size of the
		* command buffer. The transmission is kicked off if
		* DSI_CTRL_HW_CMD_WAIT_FOR_TRIGGER flag is not set. If this flag is
		* set, caller should make a separate call to trigger_command_dma() to
		* transmit the command.
		*/
		void (kickoff_command)(struct dsi_ctrl_hw ctrl,
		struct dsi_ctrl_cmd_dma_info *cmd,
		u32 flags);

		/**
		* kickoff_fifo_command() - transmits a command using FIFO in dsi
		* hardware.
		* @ctrl: Pointer to the controller host hardware.
		* @cmd: Command information.
		* @flags: Modifiers for command transmission.
		*
		* The controller hardware FIFO is programmed with command header and
		* payload. The transmission is kicked off if
		* DSI_CTRL_HW_CMD_WAIT_FOR_TRIGGER flag is not set. If this flag is
		* set, caller should make a separate call to trigger_command_dma() to
		* transmit the command.
		*/
		void (kickoff_fifo_command)(struct dsi_ctrl_hw ctrl,
		struct dsi_ctrl_cmd_dma_fifo_info *cmd,
		u32 flags);

		void (reset_cmd_fifo)(struct dsi_ctrl_hw ctrl);
		/**
		* trigger_command_dma() - trigger transmission of command buffer.
		* @ctrl: Pointer to the controller host hardware.
		*
		* This trigger can be only used if there was a prior call to
		* kickoff_command() of kickoff_fifo_command() with
		* DSI_CTRL_HW_CMD_WAIT_FOR_TRIGGER flag.
		*/
		void (trigger_command_dma)(struct dsi_ctrl_hw ctrl);

		/**
		* get_cmd_read_data() - get data read from the peripheral
		* @ctrl: Pointer to the controller host hardware.
		* @rd_buf: Buffer where data will be read into.
		* @total_read_len: Number of bytes to read.
		*/
		u32 (get_cmd_read_data)(struct dsi_ctrl_hw ctrl,
		u8 *rd_buf,
		u32 total_read_len);

		/**
		* ulps_request() - request ulps entry for specified lanes
		* @ctrl: Pointer to the controller host hardware.
		* @lanes: ORed list of lanes (enum dsi_data_lanes) which need
		* to enter ULPS.
		*
		* Caller should check if lanes are in ULPS mode by calling
		* get_lanes_in_ulps() operation.
		*/
		void (ulps_request)(struct dsi_ctrl_hw ctrl, u32 lanes);

		/**
		* ulps_exit() - exit ULPS on specified lanes
		* @ctrl: Pointer to the controller host hardware.
		* @lanes: ORed list of lanes (enum dsi_data_lanes) which need
		* to exit ULPS.
		*
		* Caller should check if lanes are in active mode by calling
		* get_lanes_in_ulps() operation.
		*/
		void (ulps_exit)(struct dsi_ctrl_hw ctrl, u32 lanes);

		/**
		* clear_ulps_request() - clear ulps request once all lanes are active
		* @ctrl: Pointer to controller host hardware.
		* @lanes: ORed list of lanes (enum dsi_data_lanes).
		*
		* ULPS request should be cleared after the lanes have exited ULPS.
		*/
		void (clear_ulps_request)(struct dsi_ctrl_hw ctrl, u32 lanes);

		/**
		* get_lanes_in_ulps() - returns the list of lanes in ULPS mode
		* @ctrl: Pointer to the controller host hardware.
		*
		* Returns an ORed list of lanes (enum dsi_data_lanes) that are in ULPS
		* state. If 0 is returned, all the lanes are active.
		*
		* Return: List of lanes in ULPS state.
		*/
		u32 (get_lanes_in_ulps)(struct dsi_ctrl_hw ctrl);

		/**
		* clamp_enable() - enable DSI clamps to keep PHY driving a stable link
		* @ctrl: Pointer to the controller host hardware.
		* @lanes: ORed list of lanes which need to be clamped.
		* @enable_ulps: TODO:??
		*/
		void (clamp_enable)(struct dsi_ctrl_hw ctrl,
		u32 lanes,
		bool enable_ulps);

		/**
		* clamp_disable() - disable DSI clamps
		* @ctrl: Pointer to the controller host hardware.
		* @lanes: ORed list of lanes which need to have clamps released.
		* @disable_ulps: TODO:??
		*/
		void (clamp_disable)(struct dsi_ctrl_hw ctrl,
		u32 lanes,
		bool disable_ulps);

		/**
		* get_interrupt_status() - returns the interrupt status
		* @ctrl: Pointer to the controller host hardware.
		*
		* Returns the ORed list of interrupts(enum dsi_status_int_type) that
		* are active. This list does not include any error interrupts. Caller
		* should call get_error_status for error interrupts.
		*
		* Return: List of active interrupts.
		*/
		u32 (get_interrupt_status)(struct dsi_ctrl_hw ctrl);

		/**
		* clear_interrupt_status() - clears the specified interrupts
		* @ctrl: Pointer to the controller host hardware.
		* @ints: List of interrupts to be cleared.
		*/
		void (clear_interrupt_status)(struct dsi_ctrl_hw ctrl, u32 ints);

		/**
		* enable_status_interrupts() - enable the specified interrupts
		* @ctrl: Pointer to the controller host hardware.
		* @ints: List of interrupts to be enabled.
		*
		* Enables the specified interrupts. This list will override the
		* previous interrupts enabled through this function. Caller has to
		* maintain the state of the interrupts enabled. To disable all
		* interrupts, set ints to 0.
		*/
		void (enable_status_interrupts)(struct dsi_ctrl_hw ctrl, u32 ints);

		/**
		* get_error_status() - returns the error status
		* @ctrl: Pointer to the controller host hardware.
		*
		* Returns the ORed list of errors(enum dsi_error_int_type) that are
		* active. This list does not include any status interrupts. Caller
		* should call get_interrupt_status for status interrupts.
		*
		* Return: List of active error interrupts.
		*/
		u64 (get_error_status)(struct dsi_ctrl_hw ctrl);

		/**
		* clear_error_status() - clears the specified errors
		* @ctrl: Pointer to the controller host hardware.
		* @errors: List of errors to be cleared.
		*/
		void (clear_error_status)(struct dsi_ctrl_hw ctrl, u64 errors);

		/**
		* enable_error_interrupts() - enable the specified interrupts
		* @ctrl: Pointer to the controller host hardware.
		* @errors: List of errors to be enabled.
		*
		* Enables the specified interrupts. This list will override the
		* previous interrupts enabled through this function. Caller has to
		* maintain the state of the interrupts enabled. To disable all
		* interrupts, set errors to 0.
		*/
		void (enable_error_interrupts)(struct dsi_ctrl_hw ctrl, u64 errors);

		/**
		* video_test_pattern_setup() - setup test pattern engine for video mode
		* @ctrl: Pointer to the controller host hardware.
		* @type: Type of test pattern.
		* @init_val: Initial value to use for generating test pattern.
		*/
		void (video_test_pattern_setup)(struct dsi_ctrl_hw ctrl,
		enum dsi_test_pattern type,
		u32 init_val);

		/**
		* cmd_test_pattern_setup() - setup test patttern engine for cmd mode
		* @ctrl: Pointer to the controller host hardware.
		* @type: Type of test pattern.
		* @init_val: Initial value to use for generating test pattern.
		* @stream_id: Stream Id on which packets are generated.
		*/
		void (cmd_test_pattern_setup)(struct dsi_ctrl_hw ctrl,
		enum dsi_test_pattern type,
		u32 init_val,
		u32 stream_id);

		/**
		* test_pattern_enable() - enable test pattern engine
		* @ctrl: Pointer to the controller host hardware.
		* @enable: Enable/Disable test pattern engine.
		*/
		void (test_pattern_enable)(struct dsi_ctrl_hw ctrl, bool enable);

		/**
		* trigger_cmd_test_pattern() - trigger a command mode frame update with
		* test pattern
		* @ctrl: Pointer to the controller host hardware.
		* @stream_id: Stream on which frame update is sent.
		*/
		void (trigger_cmd_test_pattern)(struct dsi_ctrl_hw ctrl,
		u32 stream_id);
		};

		/*
		* struct dsi_ctrl_hw - DSI controller hardware object specific to an instance
		* @base: VA for the DSI controller base address.
		* @length: Length of the DSI controller register map.
		* @index: Instance ID of the controller.
		* @feature_map: Features supported by the DSI controller.
		* @ops: Function pointers to the operations supported by the
		* controller.
		*/
		struct dsi_ctrl_hw {
		void __iomem *base;
		u32 length;
		void __iomem *mmss_misc_base;
		u32 mmss_misc_length;
		u32 index;

		/* features */
		DECLARE_BITMAP(feature_map, DSI_CTRL_MAX_FEATURES);
		struct dsi_ctrl_hw_ops ops;

		/* capabilities */
		u32 supported_interrupts;
		u64 supported_errors;
		};

		#endif /* _DSI_CTRL_HW_H_ */