Merge "ARM: dts: msm: Add EEPROM support for MSM8994 CDP"

		status = "ok";

	};

	eeprom3: qcom,eeprom@3 {

		cell-index = <3>;

		reg = <0x3>;

		qcom,eeprom-name = "onsemi_cat24c16";

		compatible = "qcom,eeprom";

		qcom,slave-addr = <0xa0>;

		qcom,cci-master = <0>;

		qcom,num-blocks = <7>;

		qcom,page0 = <0 0 0 0 0 0>;

		qcom,poll0 = <0 0 0 0 0 0>;

		qcom,saddr0 = <0xa0>;

		qcom,mem0 = <256 0x00 1 0 1 0>;

		qcom,page1 = <0 0 0 0 0 0>;

		qcom,poll1 = <0 0 0 0 0 0>;

		qcom,saddr1 = <0xa2>;

		qcom,mem1 = <256 0x00 1 0 1 0>;

		qcom,page2 = <0 0 0 0 0 0>;

		qcom,poll2 = <0 0 0 0 0 0>;

		qcom,saddr2 = <0xa4>;

		qcom,mem2 = <256 0x00 1 0 1 0>;

		qcom,page3 = <0 0 0 0 0 0>;

		qcom,poll3 = <0 0 0 0 0 0>;

		qcom,saddr3 = <0xa6>;

		qcom,mem3 = <256 0x00 1 0 1 0>;

		qcom,page4 = <0 0 0 0 0 0>;

		qcom,poll4 = <0 0 0 0 0 0>;

		qcom,saddr4 = <0xa8>;

		qcom,mem4 = <256 0x00 1 0 1 0>;

		qcom,page5 = <0 0 0 0 0 0>;

		qcom,poll5 = <0 0 0 0 0 0>;

		qcom,saddr5 = <0xaa>;

		qcom,mem5 = <256 0x00 1 0 1 0>;

		qcom,page6 = <0 0 0 0 0 0>;

		qcom,poll6 = <0 0 0 0 0 0>;

		qcom,saddr6 = <0xac>;

		qcom,mem6 = <254 0x00 1 0 1 0>;

		cam_vdig-supply = <&pm8994_l3>;

		cam_vio-supply = <&pm8994_lvs1>;

		cam_vana-supply = <&pm8994_l29>;

		qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana";

		qcom,cam-vreg-min-voltage = <1200000 0 2800000>;

		qcom,cam-vreg-max-voltage = <1200000 0 2800000>;

		qcom,cam-vreg-op-mode = <105000 0 80000>;

		qcom,gpio-no-mux = <0>;

		pinctrl-names = "cam_default", "cam_suspend";

		pinctrl-0 = <&cam_sensor_mclk2_active &cam_sensor_front_active>;

		pinctrl-1 = <&cam_sensor_mclk2_suspend &cam_sensor_front_suspend>;

		gpios = <&msm_gpio 15 0>,

			<&msm_gpio 104 0>,

			<&msm_gpio 105 0>;

		qcom,gpio-reset = <1>;

		qcom,gpio-standby = <2>;

		qcom,gpio-req-tbl-num = <0 1 2>;

		qcom,gpio-req-tbl-flags = <1 0 0>;

		qcom,gpio-req-tbl-label = "CAMIF_MCLK2",

					  "CAM_RESET2",

					  "CAM_STANDBY2";

		qcom,cam-power-seq-type = "sensor_vreg", "sensor_vreg", "sensor_vreg",

			"sensor_gpio", "sensor_gpio" , "sensor_clk";

		qcom,cam-power-seq-val = "cam_vdig", "cam_vana", "cam_vio",

			"sensor_gpio_reset", "sensor_gpio_standby","sensor_cam_mclk";

		qcom,cam-power-seq-cfg-val = <1 1 1 1 1 24000000>;

		qcom,cam-power-seq-delay = <1 1 1 30 30 5>;

		status = "ok";

		clocks = <&clock_mmss clk_mclk2_clk_src>,

				<&clock_mmss clk_camss_mclk2_clk>;

		clock-names = "cam_src_clk", "cam_clk";

	};

	qcom,camera@0 {

		cell-index = <0>;

		compatible = "qcom,camera";

		qcom,csiphy-sd-index = <2>;

		qcom,csid-sd-index = <2>;

		qcom,mount-angle = <90>;

		qcom,eeprom-src = <&eeprom1>;

		qcom,eeprom-src = <&eeprom1 &eeprom3>;

		qcom,actuator-src = <&actuator1>;

		cam_vdig-supply = <&pm8994_l3>;

		cam_vio-supply = <&pm8994_lvs1>;