Merge "msm: mdss: add support for mhl3 compilation"

	  MHL (Mobile High-Definition Link) technology

	  uses USB connector to output HDMI content

config FB_MSM_MDSS_MHL3

	depends on FB_MSM_MDSS_HDMI_PANEL

	bool "MHL3 SII8620 Support"

	default n

	---help---

	  Support the SiliconImage 8620 MHL Tx transmitter that uses

	  USB connector to output HDMI content. Transmitter is an

	  i2c device acting as an HDMI to MHL bridge. Chip supports

	  MHL 3.0 standard.

config FB_MSM_MDSS_DSI_CTRL_STATUS

	tristate "DSI controller status check feature"

	---help---

ccflags-y += -I$(src)

obj-$(CONFIG_FB_MSM_MDSS_MHL3) += mhl3/

mdss-mdp3-objs = mdp3.o mdp3_dma.o mdp3_ctrl.o dsi_status_v2.o

mdss-mdp3-objs += mdp3_ppp.o mdp3_ppp_hwio.o mdp3_ppp_data.o

obj-$(CONFIG_FB_MSM_MDSS_MDP3) += mdss-mdp3.o

#

# Makefile for the Silicon Image 8620 MHL TX device driver

#

# example invocations:	

#	For regular Linux builds

#	make ARCH=arm CROSS_COMPILE=arm-angstrom-linux-gnueabi- clean debug

#	make ARCH=arm CROSS_COMPILE=arm-angstrom-linux-gnueabi- clean release

#	make ARCH=arm CROSS_COMPILE=arm-angstrom-linux-gnueabi- clean clean

#

#	For Android driver builds - Specify different tool-chain and kernel revision

#	export PATH=~/rowboat-android/prebuilt/linux-x86/toolchain/arm-eabi-4.4.3/bin:$PATH

#	make ARCH=arm KERNELPATH=~/rowboat-android/kernel CROSS_COMPILE=arm-eabi- clean debug

#	make ARCH=arm KERNELPATH=~/rowboat-android/kernel CROSS_COMPILE=arm-eabi- clean release

#	make ARCH=arm KERNELPATH=~/rowboat-android/kernel CROSS_COMPILE=arm-eabi- clean clean

#	

#	For Android 4.0.3 (ICS):

#	export PATH=~/rowboat-android/TI-Android-ICS-4.0.3_AM37x_3.0.0/prebuilt/linux-x86/toolchain/arm-eabi-4.4.3/bin:$PATH

#	make ARCH=arm KERNELPATH=~/rowboat-android/TI-Android-ICS-4.0.3_AM37x_3.0.0/kernel CROSS_COMPILE=arm-eabi- clean debug

#	make ARCH=arm KERNELPATH=~/rowboat-android/TI-Android-ICS-4.0.3_AM37x_3.0.0/kernel CROSS_COMPILE=arm-eabi- clean release

#	make ARCH=arm KERNELPATH=~/rowboat-android/TI-Android-ICS-4.0.3_AM37x_3.0.0/kernel CROSS_COMPILE=arm-eabi- clean clean

#

#	For Android 4.2.2 (JB) Linaro release 13.04 for PandaBoard:

#	export PATH=$PATH:~/Linaro-13.04/android/prebuilts/gcc/linux-x86/arm/arm-linux-androideabi-4.7-linaro/bin

#	make ARCH=arm KERNELPATH=~/Linaro-13.04/android/kernel/linaro/pandaboard CROSS_COMPILE=arm-eabi- clean debug

#	make ARCH=arm KERNELPATH=~/Linaro-13.04/android/kernel/linaro/pandaboard CROSS_COMPILE=arm-eabi- clean release

#	make ARCH=arm KERNELPATH=~/Linaro-13.04/android/kernel/linaro/pandaboard CROSS_COMPILE=arm-eabi- clean clean

#	

ccflags-y += -I$(src)

# Silicon Image uses DEVELOPER_BUILD_ID for sandbox build to be identified during testing.

ifneq ($(DEVELOPER_BUILD_ID),)

DEVELOPER_BUILD_COPY=cp sii$(MHL_PRODUCT_NUM)drv.ko sii$(MHL_PRODUCT_NUM)drv$(DEVELOPER_BUILD_ID).ko

endif

ifneq ($(KERNELRELEASE),)

# kbuild part of makefile

#

# color annotations to use instead of leading newline chars

ccflags-y += -DANSI_COLORS

ccflags-y += -DDEBUG

ccflags-y += -DMHL_BUILD_NUM=1

ccflags-y += -DDEVELOPER_BUILD_ID=1

ccflags-y += -DBUILD_NUM_STRING=\"$(MHL_BUILD_NUM)$(DEVELOPER_BUILD_ID)\"

ccflags-y += -DMHL_PRODUCT_NUM=$(MHL_PRODUCT_NUM)

ccflags-y += -DMHL_PRODUCT_NUM=8620

ccflags-y += -DMHL_DRIVER_NAME=\"sii$(MHL_PRODUCT_NUM)drv\"

ccflags-y += -DMHL_DEVICE_NAME=\"sii-$(MHL_PRODUCT_NUM)\"

# Support Device Tree?

ifeq ($(DT_SUPPORT),1)

ccflags-y += -DSIMG_USE_DTS

endif

# Kernel level supported

ccflags-y += -DLINUX_KERNEL_VER=$(LINUX_KERNEL_VER)

#

# FORCE_OCBUS_FOR_ECTS is used to identify code added for ECTS temporary fix that prohibits use of eCBUS.

# in addition module parameter force_ocbus_for_ects needs to be set as 1 to achieve ECTS operation.

ccflags-y += -DFORCE_OCBUS_FOR_ECTS

#

# PC_MODE_VIDEO_TIMING_SUPPORT is for cases where no VIC is available from either AVIF or VSIF.

ccflags-y += -DPC_MODE_VIDEO_TIMING_SUPPORT

#

# MANUAL_INFO_FRAME_CLEAR_AT_HPD_DRIVEN_HIGH is to clear all infoframes 

#	upon driving HPD high instead of when SCDT goes low.

ccflags-y += -DMANUAL_INFO_FRAME_CLEAR_AT_HPD_DRIVEN_HIGH

#

# MEDIA_DATA_TUNNEL_SUPPORT

#	Default is enabled. Comment next line to disable.

ccflags-y += -DMEDIA_DATA_TUNNEL_SUPPORT

#

# Include REMOTE BUTTON PROTOCOL code or not

ccflags-$(CONFIG_DEBUG_DRIVER) += -DINCLUDE_RBP=1

ccflags-$(CONFIG_DEBUG_DRIVER) += -DINCLUDE_HID=$(INCLUDE_HID)

# Example of use of SiI6031 is wrapped under the following definition

# It also illustrates how 8620 driver may be integrated into MSM platform

# the flag should be disabled if not building for MSM

ccflags-$(CONFIG_DEBUG_DRIVER) += -DINCLUDE_SII6031=$(INCLUDE_SII6031)

#

# MANUAL_EDID_FETCH uses DDC master directly, instead of h/w automated method.

ccflags-y += $(MHL_HOST_PLATFORM)

ccflags-y += -DMANUAL_EDID_FETCH

# If CI2CA pin is pulled HIGH, you must define the following flag

#ccflags-y += -DALT_I2C_ADDR

# PRINT_DDC_ABORTS enables logging of all DDC_ABORTs. Default "disabled" - helps MHL2 hot plug.

# Enable only if you must for debugging. 

#ccflags-y += -DPRINT_DDC_ABORTS

# CoC_FSM_MONITORING exports CoC state machine to GPIO pins

# Enable only if you must for debugging. 

ccflags-y += -DCoC_FSM_MONITORING -DBIST_MONITORING

#BIST_DONE_DEBUG adds register dump prior to RAP{CBUS_MODE_UP}

#ccflags-y += -DBIST_DONE_DEBUG

# For si_emsc_hid-mt.c

ccflags-y += -Idrivers/hid

# Optimzations and/or workaround

ccflags-y += -DDISABLE_SPI_DMA

ccflags-y += -DUSE_SPIOPTIMIZE

ccflags-y += -DGCS_QUIRKS_FOR_SIMG

ccflags-$(CONFIG_DEBUG_DRIVER) += -DDEBUG 

# Enable VBUS sense and related operations

ccflags-$(CONFIG_DEBUG_DRIVER) += -DENABLE_VBUS_SENSE

#support for DVI sources and sinks in MHL3 mode.

ccflags-$(CONFIG_DEBUG_DRIVER) += -DMHL3_DVI_SUPPORT

#add HDMI VSDB to upstream EDID when downstream sink is DVI

#ccflags-$(CONFIG_DEBUG_DRIVER) += -DMHL3_DVI_SUPPORT_FORCE_HDMI

#

# the next lines are optional - they enable greater verbosity in debug output

#ccflags-$(CONFIG_DEBUG_DRIVER) += -DENABLE_EDID_DEBUG_PRINT

#ccflags-$(CONFIG_DEBUG_DRIVER) += -DENABLE_DUMP_INFOFRAME

#

# uncomment next line to prevent EDID parsing. Useful for debugging.

#ccflags-$(CONFIG_DEBUG_DRIVER) += -DEDID_PASSTHROUGH

obj-$(CONFIG_SII$(MHL_PRODUCT_NUM)_MHL_TX) += sii$(MHL_PRODUCT_NUM)drv.o

sii$(MHL_PRODUCT_NUM)drv-objs  += platform.o

sii$(MHL_PRODUCT_NUM)drv-objs  += mhl_linux_tx.o

sii$(MHL_PRODUCT_NUM)drv-objs  += mhl_rcp_inputdev.o

sii$(MHL_PRODUCT_NUM)drv-objs  += mhl_rbp_inputdev.o

sii$(MHL_PRODUCT_NUM)drv-objs  += mhl_supp.o

sii$(MHL_PRODUCT_NUM)drv-objs  += si_8620_drv.o

sii$(MHL_PRODUCT_NUM)drv-objs  += si_mhl2_edid_3d.o

sii$(MHL_PRODUCT_NUM)drv-objs  += si_mdt_inputdev.o

ifeq ($(INCLUDE_HID),1)

sii$(MHL_PRODUCT_NUM)drv-objs  += si_emsc_hid.o

sii$(MHL_PRODUCT_NUM)drv-objs  += si_emsc_hid-mt.o

endif

else

# Normal Makefile

# If a kernel is not specified, default to the kernel used with Android Ice Cream Sandwich

ifneq ($(KERNELPATH),)

KERNELDIR=$(KERNELPATH)

else

KERNELDIR=~/src/linux-2.6.36

#KERNELDIR=~/src/Android_ICS/kernel

endif

ARCH=arm

PWD := $(shell pwd)

.PHONY: clean

release:

	make -C $(KERNELDIR) M=$(PWD) CONFIG_SII$(MHL_PRODUCT_NUM)_MHL_TX=m CONFIG_MEDIA_DATA_TUNNEL_SUPPORT=y modules

	$(CROSS_COMPILE)strip --strip-debug sii$(MHL_PRODUCT_NUM)drv.ko

	$(DEVELOPER_BUILD_COPY)

debug:

	rm -f platform.o

	make -C $(KERNELDIR) M=$(PWD) CONFIG_SII$(MHL_PRODUCT_NUM)_MHL_TX=m CONFIG_MEDIA_DATA_TUNNEL_SUPPORT=y CONFIG_DEBUG_DRIVER=y modules

	$(DEVELOPER_BUILD_COPY)

clean:

	make -C $(KERNELDIR) M=$(PWD) CONFIG_SII$(MHL_PRODUCT_NUM)_MHL_TX=m clean

endif

ccflags-y += -DPRINT_DDC_ABORTS

ccflags-y += -DSIMG_USE_DTS

ccflags-y += -DINCLUDE_HID=0

ccflags-y += -DINCLUDE_RBP=0

ccflags-y += -DLINUX_KERNEL_VER=310

ccflags-y += -DINCLUDE_SII6031=0

mdss-mhl3-objs := platform.o

mdss-mhl3-objs += mhl_linux_tx.o

mdss-mhl3-objs += mhl_rcp_inputdev.o

mdss-mhl3-objs += mhl_supp.o

mdss-mhl3-objs += si_8620_drv.o

mdss-mhl3-objs += si_mhl2_edid_3d.o

mdss-mhl3-objs += si_mdt_inputdev.o

obj-y += mdss-mhl3.o