Donate to e Foundation | Murena handsets with /e/OS | Own a part of Murena! Learn more

Commit 7211da17 authored by Grant Likely's avatar Grant Likely
Browse files

Revert "dt: add documentation of ARM dt boot interface" 



This reverts commit 9830fcd6.

The ARM dt support has not been merged yet; this documentation update
was premature.

Signed-off-by: default avatarGrant Likely <grant.likely@secretlab.ca>
parent 9830fcd6

Documentation/arm/Booting

+4 −29
Original line number Diff line number Diff line
@@ -65,19 +65,13 @@ looks at the connected hardware is beyond the scope of this document. 
The boot loader must ultimately be able to provide a MACH_TYPE_xxx

value to the kernel. (see linux/arch/arm/tools/mach-types).



4. Setup boot data

------------------



4. Setup the kernel tagged list

-------------------------------



Existing boot loaders:		OPTIONAL, HIGHLY RECOMMENDED

New boot loaders:		MANDATORY



The boot loader must provide either a tagged list or a dtb image for

passing configuration data to the kernel.  The physical address of the

boot data is passed to the kernel in register r2.



4a. Setup the kernel tagged list

--------------------------------



The boot loader must create and initialise the kernel tagged list.

A valid tagged list starts with ATAG_CORE and ends with ATAG_NONE.

The ATAG_CORE tag may or may not be empty.  An empty ATAG_CORE tag
@@ -107,24 +101,6 @@ The tagged list must be placed in a region of memory where neither 
the kernel decompressor nor initrd 'bootp' program will overwrite

it.  The recommended placement is in the first 16KiB of RAM.



4b. Setup the device tree

-------------------------



The boot loader must load a device tree image (dtb) into system ram

at a 64bit aligned address and initialize it with the boot data.  The

dtb format is documented in Documentation/devicetree/booting-without-of.txt.

The kernel will look for the dtb magic value of 0xd00dfeed at the dtb

physical address to determine if a dtb has been passed instead of a

tagged list.



The boot loader must pass at a minimum the size and location of the

system memory, and the root filesystem location.  The dtb must be

placed in a region of memory where the kernel decompressor will not

overwrite it.  The recommended placement is in the first 16KiB of RAM

with the caveat that it may not be located at physical address 0 since

the kernel interprets a value of 0 in r2 to mean neither a tagged list

nor a dtb were passed.



5. Calling the kernel image

---------------------------
@@ -149,8 +125,7 @@ In either case, the following conditions must be met: 
- CPU register settings

  r0 = 0,

  r1 = machine type number discovered in (3) above.

  r2 = physical address of tagged list in system RAM, or

       physical address of device tree block (dtb) in system RAM

  r2 = physical address of tagged list in system RAM.



- CPU mode

  All forms of interrupts must be disabled (IRQs and FIQs)

Documentation/devicetree/booting-without-of.txt

+0 −40
Original line number Diff line number Diff line
@@ -13,7 +13,6 @@ Table of Contents 


  I - Introduction

    1) Entry point for arch/powerpc

    2) Entry point for arch/arm



  II - The DT block format

    1) Header
@@ -226,45 +225,6 @@ it with special cases. 
  cannot support both configurations with Book E and configurations

  with classic Powerpc architectures.



2) Entry point for arch/arm

---------------------------



   There is one single entry point to the kernel, at the start

   of the kernel image. That entry point supports two calling

   conventions.  A summary of the interface is described here.  A full

   description of the boot requirements is documented in

   Documentation/arm/Booting



        a) ATAGS interface.  Minimal information is passed from firmware

        to the kernel with a tagged list of predefined parameters.



                r0 : 0



                r1 : Machine type number



                r2 : Physical address of tagged list in system RAM



        b) Entry with a flattened device-tree block.  Firmware loads the

        physical address of the flattened device tree block (dtb) into r2,

        r1 is not used, but it is considered good practise to use a valid

        machine number as described in Documentation/arm/Booting.



                r0 : 0



                r1 : Valid machine type number.  When using a device tree,

                a single machine type number will often be assigned to

                represent a class or family of SoCs.



                r2 : physical pointer to the device-tree block

                (defined in chapter II) in RAM.  Device tree can be located

                anywhere in system RAM, but it should be aligned on a 32 bit

                boundary.



   The kernel will differentiate between ATAGS and device tree booting by

   reading the memory pointed to by r1 and looking for either the flattened

   device tree block magic value (0xd00dfeed) or the ATAG_CORE value at

   offset 0x4 from r2 (0x54410001).





II - The DT block format

========================