Loading Documentation/kernel-parameters.txt +8 −3 Original line number Original line Diff line number Diff line Loading @@ -294,7 +294,9 @@ and is between 256 and 4096 characters. It is defined in the file Possible values are: Possible values are: isolate - enable device isolation (each device, as far isolate - enable device isolation (each device, as far as possible, will get its own protection as possible, will get its own protection domain) domain) [default] share - put every device behind one IOMMU into the same protection domain fullflush - enable flushing of IO/TLB entries when fullflush - enable flushing of IO/TLB entries when they are unmapped. Otherwise they are they are unmapped. Otherwise they are flushed before they will be reused, which flushed before they will be reused, which Loading Loading @@ -1201,8 +1203,8 @@ and is between 256 and 4096 characters. It is defined in the file it is equivalent to "nosmp", which also disables it is equivalent to "nosmp", which also disables the IO APIC. the IO APIC. max_addr=[KMG] [KNL,BOOT,ia64] All physical memory greater than or max_addr=nn[KMG] [KNL,BOOT,ia64] All physical memory greater than equal to this physical address is ignored. or equal to this physical address is ignored. max_luns= [SCSI] Maximum number of LUNs to probe. max_luns= [SCSI] Maximum number of LUNs to probe. Should be between 1 and 2^32-1. Should be between 1 and 2^32-1. Loading Loading @@ -1302,6 +1304,9 @@ and is between 256 and 4096 characters. It is defined in the file mga= [HW,DRM] mga= [HW,DRM] min_addr=nn[KMG] [KNL,BOOT,ia64] All physical memory below this physical address is ignored. mminit_loglevel= mminit_loglevel= [KNL] When CONFIG_DEBUG_MEMORY_INIT is set, this [KNL] When CONFIG_DEBUG_MEMORY_INIT is set, this parameter allows control of the logging verbosity for parameter allows control of the logging verbosity for Loading Documentation/networking/phy.txt +1 −1 Original line number Original line Diff line number Diff line Loading @@ -96,7 +96,7 @@ Letting the PHY Abstraction Layer do Everything static void adjust_link(struct net_device *dev); static void adjust_link(struct net_device *dev); Next, you need to know the device name of the PHY connected to this device. Next, you need to know the device name of the PHY connected to this device. The name will look something like, "phy0:0", where the first number is the The name will look something like, "0:00", where the first number is the bus id, and the second is the PHY's address on that bus. Typically, bus id, and the second is the PHY's address on that bus. Typically, the bus is responsible for making its ID unique. the bus is responsible for making its ID unique. Loading MAINTAINERS +1 −1 Original line number Original line Diff line number Diff line Loading @@ -1809,7 +1809,7 @@ S: Maintained FTRACE FTRACE P: Steven Rostedt P: Steven Rostedt M: srostedt@redhat.com M: rostedt@goodmis.org S: Maintained S: Maintained FUJITSU FR-V (FRV) PORT FUJITSU FR-V (FRV) PORT Loading Makefile +1 −1 Original line number Original line Diff line number Diff line VERSION = 2 VERSION = 2 PATCHLEVEL = 6 PATCHLEVEL = 6 SUBLEVEL = 28 SUBLEVEL = 28 EXTRAVERSION = -rc5 EXTRAVERSION = -rc6 NAME = Killer Bat of Doom NAME = Killer Bat of Doom # *DOCUMENTATION* # *DOCUMENTATION* Loading arch/arm/mach-pxa/include/mach/pxafb.h +1 −0 Original line number Original line Diff line number Diff line Loading @@ -33,6 +33,7 @@ #define LCD_CONN_TYPE(_x) ((_x) & 0x0f) #define LCD_CONN_TYPE(_x) ((_x) & 0x0f) #define LCD_CONN_WIDTH(_x) (((_x) >> 4) & 0x1f) #define LCD_CONN_WIDTH(_x) (((_x) >> 4) & 0x1f) #define LCD_TYPE_MASK 0xf #define LCD_TYPE_UNKNOWN 0 #define LCD_TYPE_UNKNOWN 0 #define LCD_TYPE_MONO_STN 1 #define LCD_TYPE_MONO_STN 1 #define LCD_TYPE_MONO_DSTN 2 #define LCD_TYPE_MONO_DSTN 2 Loading Loading
Documentation/kernel-parameters.txt +8 −3 Original line number Original line Diff line number Diff line Loading @@ -294,7 +294,9 @@ and is between 256 and 4096 characters. It is defined in the file Possible values are: Possible values are: isolate - enable device isolation (each device, as far isolate - enable device isolation (each device, as far as possible, will get its own protection as possible, will get its own protection domain) domain) [default] share - put every device behind one IOMMU into the same protection domain fullflush - enable flushing of IO/TLB entries when fullflush - enable flushing of IO/TLB entries when they are unmapped. Otherwise they are they are unmapped. Otherwise they are flushed before they will be reused, which flushed before they will be reused, which Loading Loading @@ -1201,8 +1203,8 @@ and is between 256 and 4096 characters. It is defined in the file it is equivalent to "nosmp", which also disables it is equivalent to "nosmp", which also disables the IO APIC. the IO APIC. max_addr=[KMG] [KNL,BOOT,ia64] All physical memory greater than or max_addr=nn[KMG] [KNL,BOOT,ia64] All physical memory greater than equal to this physical address is ignored. or equal to this physical address is ignored. max_luns= [SCSI] Maximum number of LUNs to probe. max_luns= [SCSI] Maximum number of LUNs to probe. Should be between 1 and 2^32-1. Should be between 1 and 2^32-1. Loading Loading @@ -1302,6 +1304,9 @@ and is between 256 and 4096 characters. It is defined in the file mga= [HW,DRM] mga= [HW,DRM] min_addr=nn[KMG] [KNL,BOOT,ia64] All physical memory below this physical address is ignored. mminit_loglevel= mminit_loglevel= [KNL] When CONFIG_DEBUG_MEMORY_INIT is set, this [KNL] When CONFIG_DEBUG_MEMORY_INIT is set, this parameter allows control of the logging verbosity for parameter allows control of the logging verbosity for Loading
Documentation/networking/phy.txt +1 −1 Original line number Original line Diff line number Diff line Loading @@ -96,7 +96,7 @@ Letting the PHY Abstraction Layer do Everything static void adjust_link(struct net_device *dev); static void adjust_link(struct net_device *dev); Next, you need to know the device name of the PHY connected to this device. Next, you need to know the device name of the PHY connected to this device. The name will look something like, "phy0:0", where the first number is the The name will look something like, "0:00", where the first number is the bus id, and the second is the PHY's address on that bus. Typically, bus id, and the second is the PHY's address on that bus. Typically, the bus is responsible for making its ID unique. the bus is responsible for making its ID unique. Loading
MAINTAINERS +1 −1 Original line number Original line Diff line number Diff line Loading @@ -1809,7 +1809,7 @@ S: Maintained FTRACE FTRACE P: Steven Rostedt P: Steven Rostedt M: srostedt@redhat.com M: rostedt@goodmis.org S: Maintained S: Maintained FUJITSU FR-V (FRV) PORT FUJITSU FR-V (FRV) PORT Loading
Makefile +1 −1 Original line number Original line Diff line number Diff line VERSION = 2 VERSION = 2 PATCHLEVEL = 6 PATCHLEVEL = 6 SUBLEVEL = 28 SUBLEVEL = 28 EXTRAVERSION = -rc5 EXTRAVERSION = -rc6 NAME = Killer Bat of Doom NAME = Killer Bat of Doom # *DOCUMENTATION* # *DOCUMENTATION* Loading
arch/arm/mach-pxa/include/mach/pxafb.h +1 −0 Original line number Original line Diff line number Diff line Loading @@ -33,6 +33,7 @@ #define LCD_CONN_TYPE(_x) ((_x) & 0x0f) #define LCD_CONN_TYPE(_x) ((_x) & 0x0f) #define LCD_CONN_WIDTH(_x) (((_x) >> 4) & 0x1f) #define LCD_CONN_WIDTH(_x) (((_x) >> 4) & 0x1f) #define LCD_TYPE_MASK 0xf #define LCD_TYPE_UNKNOWN 0 #define LCD_TYPE_UNKNOWN 0 #define LCD_TYPE_MONO_STN 1 #define LCD_TYPE_MONO_STN 1 #define LCD_TYPE_MONO_DSTN 2 #define LCD_TYPE_MONO_DSTN 2 Loading
