fbdev: msm: Add snapshot of display framebuffer driver

ADV7533 DSI to HDMI bridge

Required properties:

- compatible:				Must be "adv7533"

- reg:					Main I2C slave ID (for I2C host driver)

- adi,video-mode:			Excepted a number and possible inputs are 0 to 3, while:

					3 = 1080p

					2 = 720p

					1 = 480p

					0 = 1080p pattern

- adi,main-addr:			Main I2C slave ID

- adi,cec-dsi-addr:			CEC DSI I2C slave ID

Optional properties:

- adi,enable-audio:

- adi,disable-gpios:

- adi,irq-gpio:				Main IRQ gpio mapping

- adi,hpd-irq-gpio:			HPD IRQ gpio mapping

- adi,switch-gpio:			DSI switch gpio mapping

- qcom,supply-names:			Regulator names that supply 5v to bridge chip

- qcom,min-voltage-level		Minimum voltage level to be supplied to bridge chip

- qcom,max-voltage-level		Maximum voltage level to be supplied to bridge chip

- qcom,enable-load			Load current to bridge chip when enabled

- qcom,disable-load			Load current to bridge chip when disabled

- qcom,post-on-sleep			Sleep time (ms) to indicate the sleep

					time after the vreg is enabled

Example:

&soc {

	i2c@78b8000 {

		adv7533@39 {

			compatible = "adv7533";

			reg = <0x39>;

			adi,video-mode = <3>; /* 3 = 1080p */

			adi,main-addr = <0x39>;

			adi,cec-dsi-addr = <0x3C>;

			adi,enable-audio;

			pinctrl-names = "pmx_adv7533_active","pmx_adv7533_suspend";

			pinctrl-0 = <&adv7533_int_active &adv7533_hpd_int_active &adv7533_switch_active>;

			pinctrl-1 = <&adv7533_int_suspend &adv7533_hpd_int_suspend &adv7533_switch_suspend>;

			adi,irq-gpio = <&msm_gpio 31 0x2002>;

			adi,hpd-irq-gpio = <&msm_gpio 20 0x2003>;

			adi,switch-gpio = <&msm_gpio 32 0x0>;

			hpd-5v-en-supply = <&adv_vreg>;

			qcom,supply-names = "hpd-5v-en";

			qcom,min-voltage-level = <0>;

			qcom,max-voltage-level = <0>;

			qcom,enable-load = <0>;

			qcom,disable-load = <0>;

			qcom,post-on-sleep = <10>;

		};

	};

};

LT8912 DSI to HDMI bridge

Required properties:

- compatible:				Must be "lontium,lt8912"

- reg:					Main I2C slave ID (for I2C host driver)

Optional properties:

- qcom,hdmi-reset:				Main reset gpio mapping

Example:

&soc {

	i2c@78b8000 {

		lt8912@48 {

			compatible = "lontium,lt8912";

			reg = <0x48>;

			qcom,hdmi-reset = <&tlmm 64 0x0>;

		};

	};

};

Qualcomm mdss-dsi-panel

Qualcomm Technologies, Inc. mdss-dsi-panel

mdss-dsi-panel is a dsi panel device which supports panels that

are compatible with MIPI display serial interface specification.

					This property specifies the version

					for DSI HW that this panel will work with

					"qcom,dsi-panel-v2" = DSI V2.0

					"qcom,msm-dsi-v2" = DSI V2.0

- status:        			This property applies to DSI V2 panels only.

					This property should not be added for panels

					that work based on version "V6.0"

					"display_2" = DISPLAY_2

- qcom,mdss-dsi-panel-timings:		An array of length 12 that specifies the PHY

					timing settings for the panel.

- qcom,mdss-dsi-panel-timings-8996:		An array of length 40 char that specifies the 8996 PHY lane

					timing settings for the panel.

- qcom,mdss-dsi-panel-timings-phy-v2:	An array of length 40 char that specifies the PHY version 2

					lane timing settings for the panel.

- qcom,mdss-dsi-panel-timings-phy-12nm: An array of length 8 char that specifies the 12nm DSI PHY

					lane timing settings for the panel.

- qcom,mdss-dsi-on-command:		A byte stream formed by multiple dcs packets base on

					qcom dsi controller protocol.

					byte 0: dcs data type

						 transmitted

					byte 5, 6: 16 bits length in network byte order

					byte 7 and beyond: number byte of payload

- qcom,mdss-dsi-lp-mode-on:		This is used to enable display low persistence mode.

					A byte stream formed by multiple dcs packets base on

					qcom dsi controller protocol.

					byte 0: dcs data type

					byte 1: set to indicate this is an individual packet

						 (no chain)

					byte 2: virtual channel number

					byte 3: expect ack from client (dcs read command)

					byte 4: wait number of specified ms after dcs command

						 transmitted

					byte 5, 6: 16 bits length in network byte order

					byte 7 and beyond: number byte of payload

- qcom,mdss-dsi-lp-mode-off:		This is used to disable display low persistence mode.

					A byte stream formed by multiple dcs packets base on

					qcom dsi controller protocol.

					byte 0: dcs data type

					byte 1: set to indicate this is an individual packet

						 (no chain)

					byte 2: virtual channel number

					byte 3: expect ack from client (dcs read command)

					byte 4: wait number of specified ms after dcs command

						 transmitted

					byte 5, 6: 16 bits length in network byte order

					byte 7 and beyond: number byte of payload

- qcom,mdss-dsi-post-panel-on-command:	same as "qcom,mdss-dsi-on-command" except commands are

					sent after displaying an image.

- qcom,mdss-dsi-idle-on-command:	same as "qcom,mdss-dsi-on-command". Set of DCS command

					used for idle mode entry.

- qcom,mdss-dsi-idle-off-command:	same as "qcom,mdss-dsi-on-command". Set of DCS command

					used for idle mode exit.

Note, if a short DCS packet(i.e packet with Byte 0:dcs data type as 05) mentioned in

qcom,mdss-dsi-on-command/qcom,mdss-dsi-off-command stream fails to transmit,

then 3 options can be tried.

					60 = 60 frames per second (default)

- qcom,mdss-dsi-panel-clockrate:	A 64 bit value specifies the panel clock speed in Hz.

					0 = default value.

- qcom,mdss-mdp-kickoff-threshold:	This property can be used to define a region

					(in terms of scanlines) where the

hardware is allowed

					to trigger a data transfer from MDP to DSI.

					If this property is used, the region must be defined setting

					two values, the low and the high thresholds:

					<low_threshold high_threshold>

					Where following condition must be met:

					low_threshold < high_threshold

					These values will be used by the driver in such way that if

					the Driver receives a request to kickoff a transfer (MDP to DSI),

					the transfer will be triggered only if the following condition

					is satisfied:

					low_threshold < scanline < high_threshold

					If the condition is not met, then the driver will delay the

					transfer by the time defined in the following property:

					"qcom,mdss-mdp-kickoff-delay".

					So in order to use this property, the delay property must

					be defined as well and greater than 0.

- qcom,mdss-mdp-kickoff-delay:	This property defines the delay in microseconds that

					the driver will delay before triggering an MDP transfer if the

					thresholds defined by the following property are not met:

					"qcom,mdss-mdp-kickoff-threshold".

					So in order to use this property, the threshold property must

					be defined as well. Note that this delay cannot be zero

					and also should not be greater than

the fps window.

					i.e. For 60fps value should not exceed

16666 uS.

- qcom,mdss-mdp-transfer-time-us:	Specifies the dsi transfer time for command mode

					panels in microseconds. Driver uses this number to adjust

					the clock rate according to the expected transfer time.

					to the physical width in the framebuffer information.

- qcom,mdss-pan-physical-height-dimension:	Specifies panel physical height in mm which corresponds

					to the physical height in the framebuffer information.

- qcom,mdss-dsi-mode-sel-gpio-state:	String that specifies the lcd mode for panel

					(such as single-port/dual-port), if qcom,panel-mode-gpio

					binding is defined in dsi controller.

					"dual_port" = Set GPIO to LOW

					"single_port" = Set GPIO to HIGH

- qcom,mdss-dsi-panel-mode-gpio-state:	String that specifies the mode state for panel if it is defined

					in dsi controller.

					"high" = Set GPIO to HIGH

					"low" = Set GPIO to LOW

					The default value is "dual_port".

- qcom,mdss-tear-check-disable:		Boolean to disable mdp tear check. Tear check is enabled by default to avoid

					tearing. Other tear-check properties are ignored if this property is present.

					The below tear check configuration properties can be individually tuned if

					2A/2B command.

- qcom,dcs-cmd-by-left:			Boolean to indicate that dcs command are sent

					through the left DSI controller only in a dual-dsi configuration

- qcom,mdss-dsi-panel-hdr-enabled:	Boolean to indicate HDR support in panel.

- qcom,mdss-dsi-panel-hdr-color-primaries:

					Array of 8 unsigned integers denoting chromaticity of panel.These

					values are specified in nits units. The value range is 0 through 50000.

					To obtain real chromacity, these values should be divided by factor of

					50000. The structure of array is defined in below order

						value 1: x value of white chromaticity of display panel

						value 2: y value of white chromaticity of display panel

						value 3: x value of red chromaticity of display panel

						value 4: y value of red chromaticity of display panel

						value 5: x value of green chromaticity of display panel

						value 6: y value of green chromaticity of display panel

						value 7: x value of blue chromaticity of display panel

						value 8: y value of blue chromaticity of display panel

- qcom,mdss-dsi-panel-peak-brightness:	Maximum brightness supported by panel.In absence of maximum value

					typical value becomes peak brightness. Value is specified in nits units.

					To obtail real peak brightness, this value should be divided by factor of

					10000.

- qcom,mdss-dsi-panel-blackness-level:	Blackness level supported by panel. Blackness level is defined as

					ratio of peak brightness to contrast. Value is specified in nits units.

					To obtail real blackness level, this value should be divided by factor of

					10000.

- qcom,mdss-dsi-lp11-init:		Boolean used to enable the DSI clocks and data lanes (low power 11)

					before issuing hardware reset line.

- qcom,mdss-dsi-init-delay-us:		Delay in microseconds(us) before performing any DSI activity in lp11

					fields in the supply entry, refer to the qcom,ctrl-supply-entries

					binding above.

- qcom,config-select:			Optional property to select default configuration.

- qcom,panel-allow-phy-poweroff:	A boolean property indicates that panel allows to turn off the phy power

					supply during idle screen. A panel should able to handle the dsi lanes

					in floating state(not LP00 or LP11) to turn on this property. Software

					turns off PHY pmic power supply, phy ldo and DSI Lane ldo during

					idle screen (footswitch control off) when this property is enabled.

[[Optional config sub-nodes]]		These subnodes provide different configurations for a given same panel.

					Default configuration can be chosen by specifying phandle of the

					selected subnode in the qcom,config-select.

					to a non-DSI interface.

- qcom,bridge-name:			A string to indicate the name of the bridge chip connected to DSI. qcom,bridge-name

					is required if qcom,dba-panel is defined for the panel.

- qcom,hdmi-mode:			Indicates where current panel is HDMI mode, otherwise, it will be DVI mode.

- qcom,adjust-timer-wakeup-ms:		An integer value to indicate the timer delay(in ms) to accommodate

					s/w delay while configuring the event timer wakeup logic.

Note, if a given optional qcom,* binding is not present, then the driver will configure

the default values specified.

Note, all the "qcom,supply-*" properties have their definitions in mdss-dsi-txt.

Example:

&mdss_mdp {

	dsi_sim_vid: qcom,mdss_dsi_sim_video {

		qcom,mdss-dsi-underflow-color = <0xff>;

		qcom,mdss-dsi-bl-min-level = <1>;

		qcom,mdss-dsi-bl-max-level = < 15>;

		qcom,mdss-brightness-max-level = <255>;

		qcom,mdss-dsi-interleave-mode = <0>;

		qcom,mdss-dsi-panel-type = "dsi_video_mode";

		qcom,mdss-dsi-te-check-enable;

		qcom,mdss-dsi-dma-trigger = <0>;

		qcom,mdss-dsi-panel-framerate = <60>;

		qcom,mdss-dsi-panel-clockrate = <424000000>;

		qcom,mdss-mdp-kickoff-threshold = <11 2430>;

		qcom,mdss-mdp-kickoff-delay = <1000>;

		qcom,mdss-mdp-transfer-time-us = <12500>;

		qcom,mdss-dsi-panel-timings = [7d 25 1d 00 37 33

					22 27 1e 03 04 00];

                qcom,mdss-dsi-panel-timings-8996 = [23 20 06 09 05 03 04 a0

                qcom,mdss-dsi-panel-timings-phy-v2 = [23 20 06 09 05 03 04 a0

                                23 20 06 09 05 03 04 a0

                                23 20 06 09 05 03 04 a0

                                23 20 06 09 05 03 04 a0

                                23 2e 06 08 05 03 04 a0];

                qcom,mdss-dsi-panel-timings-phy-12nm =

				[a9 4e 56 0b 8a 4d 0b d6];

		qcom,mdss-dsi-on-command = [32 01 00 00 00 00 02 00 00

					29 01 00 00 10 00 02 FF 99];

		qcom,mdss-dsi-on-command-state = "dsi_lp_mode";

		qcom,mdss-dsi-off-command = [22 01 00 00 00 00 00];

		qcom,mdss-dsi-off-command-state = "dsi_hs_mode";

		qcom,mdss-dsi-lp-mode-on = [32 01 00 00 00 00 02 00 00

					29 01 00 00 10 00 02 FF 99];

		qcom,mdss-dsi-lp-mode-off = [22 01 00 00 00 00 00];

		qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_wled";

		qcom,mdss-dsi-pan-enable-dynamic-fps;

		qcom,mdss-dsi-pan-fps-update = "dfps_suspend_resume_mode";

		qcom,5v-boost-gpio = <&pm8994_gpios 14 0>;

		qcom,mdss-pan-physical-width-dimension = <60>;

		qcom,mdss-pan-physical-height-dimension = <140>;

		qcom,mdss-dsi-mode-sel-gpio-state = "dsc_mode";

		qcom,mdss-dsi-panel-mode-gpio-state = "low";

		qcom,mdss-tear-check-sync-cfg-height = <0xfff0>;

		qcom,mdss-tear-check-sync-init-val = <1280>;

		qcom,mdss-tear-check-sync-threshold-start = <4>;

		qcom,suspend-ulps-enabled;

		qcom,panel-roi-alignment = <4 4 2 2 20 20>;

		qcom,esd-check-enabled;

		qcom,panel-allow-phy-poweroff;

		qcom,mdss-dsi-panel-status-command = [06 01 00 01 05 00 02 0A 08];

		qcom,mdss-dsi-panel-status-command-state = "dsi_lp_mode";

		qcom,mdss-dsi-panel-status-check-mode = "reg_read";

				qcom,supply-max-voltage = <2800000>;

				qcom,supply-enable-load = <100000>;

				qcom,supply-disable-load = <100>;

				qcom,supply-ulp-load = <100>;

				qcom,supply-pre-on-sleep = <0>;

				qcom,supply-post-on-sleep = <0>;

				qcom,supply-pre-off-sleep = <0>;

				qcom,supply-max-voltage = <1800000>;

				qcom,supply-enable-load = <100000>;

				qcom,supply-disable-load = <100>;

				qcom,supply-ulp-load = <100>;

				qcom,supply-pre-on-sleep = <0>;

				qcom,supply-post-on-sleep = <0>;

				qcom,supply-pre-off-sleep = <0>;

Qualcomm Technologies, Inc. mdss-dsi

mdss-dsi is the master DSI device which supports multiple DSI host controllers that

are compatible with MIPI display serial interface specification.

Required properties:

- compatible:				Must be "qcom,mdss-dsi"

- hw-config:				Specifies the DSI host setup configuration

					"hw-config" = "single_dsi"

					"hw-config" = "dual_dsi"

					"hw-config" = "split_dsi"

- ranges:				The standard property which specifies the child address

					space, parent address space and the length.

- vdda-supply:				Phandle for vreg regulator device node.

Bus Scaling Data:

- qcom,msm-bus,name:		String property describing MDSS client.

- qcom, msm-bus,num-cases:	This is the number of bus scaling use cases

				defined in the vectors property. This must be

				set to <2> for MDSS DSI driver where use-case 0

				is used to remove BW votes from the system. Use

				case 1 is used to generate bandwidth requestes

				when sending command packets.

- qcom,msm-bus,num-paths:	This represents number of paths in each bus

				scaling usecase. This value depends on number of

				AXI master ports dedicated to MDSS for

				particular chipset.

- qcom,msm-bus,vectors-KBps:	A series of 4 cell properties, with a format

				of (src, dst, ab, ib) which is defined at

				Documentation/devicetree/bindings/arm/msm/msm_bus.txt.

				DSI driver should always set average bandwidth

				(ab) to 0 and always use instantaneous

				bandwidth(ib) values.

Optional properties:

- vcca-supply:				Phandle for vcca regulator device node.

- qcom,<type>-supply-entries:		A node that lists the elements of the supply used by the

					a particular "type" of DSI modulee. The module "types"

					can be "core", "ctrl", and "phy". Within the same type,

					there can be more than one instance of this binding,

					in which case the entry would be appended with the

					supply entry index.

					e.g. qcom,ctrl-supply-entry@0

					-- qcom,supply-name: name of the supply (vdd/vdda/vddio)

					-- qcom,supply-min-voltage: minimum voltage level (uV)

					-- qcom,supply-max-voltage: maximum voltage level (uV)

					-- qcom,supply-enable-load: load drawn (uA) from enabled supply

					-- qcom,supply-disable-load: load drawn (uA) from disabled supply

					-- qcom,supply-ulp-load: load drawn (uA) from supply in ultra-low power mode

					-- qcom,supply-pre-on-sleep: time to sleep (ms) before turning on

					-- qcom,supply-post-on-sleep: time to sleep (ms) after turning on

					-- qcom,supply-pre-off-sleep: time to sleep (ms) before turning off

					-- qcom,supply-post-off-sleep: time to sleep (ms) after turning off

- pll-src-config			Specified the source PLL for the DSI

					link clocks:

					"PLL0" - Clocks sourced out of DSI PLL0

					"PLL1" - Clocks sourced out of DSI PLL1

					This property is only valid for

					certain DSI hardware configurations

					mentioned in the "hw-config" binding above.

					For example, in split_dsi config, the clocks can

					only be sourced out of PLL0. For

					dual_dsi, both PLL would be active.

					For single DSI, it is possible to

					select either PLL. If no value is specified,

					the default value for single DSI is set as PLL0.

- qcom,mmss-ulp-clamp-ctrl-offset:	Specifies the offset for dsi ulps clamp control register.

- qcom,mmss-phyreset-ctrl-offset:	Specifies the offset for dsi phy reset control register.

- qcom,dsi-clk-ln-recovery:		Boolean which enables the clk lane recovery

mdss-dsi-ctrl is a dsi controller device which is treated as a subnode of the mdss-dsi device.

Required properties:

- compatible:				Must be "qcom,mdss-dsi-ctrl"

- cell-index:				Specifies the controller used among the two controllers.

- reg: 					Base address and length of the different register

					regions(s) required for DSI device functionality.

- reg-names: 				A list of strings that map in order to the list of regs.

					"dsi_ctrl" - MDSS DSI controller register region

					"dsi_phy" - MDSS DSI PHY register region

					"dsi_phy_regulator" - MDSS DSI PHY REGULATOR region

					"mmss_misc_phys" - Register region for MMSS DSI clamps

- vdd-supply:				Phandle for vdd regulator device node.

- vddio-supply:				Phandle for vdd-io regulator device node.

- qcom,mdss-fb-map-prim:		pHandle that specifies the framebuffer to which the

					primary interface is mapped.

- qcom,mdss-mdp:			pHandle that specifies the mdss-mdp device.

- qcom,platform-regulator-settings:	An array of length 7 or 5 that specifies the PHY

					regulator settings. It use 5 bytes for 8996 pll.

- qcom,platform-strength-ctrl:		An array of length 2 or 10 that specifies the PHY

					strengthCtrl settings. It use 10 bytes for 8996 pll.

- qcom,platform-lane-config:		An array of length 45 or 20 that specifies the PHY

					lane configuration settings. It use 20 bytes for 8996 pll.

- qcom,platform-bist-ctrl:		An array of length 6 that specifies the PHY

					BIST ctrl settings.

- qcom,dsi-pref-prim-pan:		phandle that specifies the primary panel to be used

					with the controller.

Optional properties:

- label:		        	A string used to describe the controller used.

- qcom,mdss-fb-map:			pHandle that specifies the framebuffer to which the

					interface is mapped.

- qcom,mdss-fb-map-sec:			pHandle that specifies the framebuffer to which the

					secondary interface is mapped.

- qcom,platform-enable-gpio:		Specifies the panel lcd/display enable gpio.

- qcom,platform-reset-gpio:		Specifies the panel reset gpio.

- qcom,platform-te-gpio:		Specifies the gpio used for TE.

- qcom,platform-bklight-en-gpio:	Specifies the gpio used to enable display back-light

- qcom,platform-mode-gpio:		Select video/command mode of panel through gpio when it supports

					both modes.

- qcom,platform-intf-mux-gpio:		Select dsi/external(hdmi) interface through gpio when it supports

					either dsi or external interface.

- pinctrl-names:			List of names to assign mdss pin states defined in pinctrl device node

					Refer to pinctrl-bindings.txt

- pinctrl-<0..n>:			Lists phandles each pointing to the pin configuration node within a pin

					controller. These pin configurations are installed in the pinctrl

					device node. Refer to pinctrl-bindings.txt

- qcom,regulator-ldo-mode:		Boolean to enable ldo mode for the dsi phy regulator

- qcom,null-insertion-enabled:		Boolean to enable NULL packet insertion

					feature for DSI controller.

- qcom,dsi-irq-line:			Boolean specifies if DSI has a different irq line than mdp.

- qcom,lane-map:			Specifies the data lane swap configuration.

					"lane_map_0123" = <0 1 2 3> (default value)

					"lane_map_3012" = <3 0 1 2>

					"lane_map_2301" = <2 3 0 1>

					"lane_map_1230" = <1 2 3 0>

					"lane_map_0321" = <0 3 2 1>

					"lane_map_1032" = <1 0 3 2>

					"lane_map_2103" = <2 1 0 3>

					"lane_map_3210" = <3 2 1 0>

- qcom,pluggable			Boolean to enable hotplug feature.

- qcom,timing-db-mode:			Boolean specifies dsi timing mode registers are supported or not.

- qcom,display-id			A string indicates the display ID for the controller.

					The possible values are:

					- "primary"

					- "secondary"

					- "tertiary"

- qcom,bridge-index:			Instance id of the bridge chip connected to DSI. qcom,bridge-index is

					required if a bridge chip panel is used.

Example:

	mdss_dsi: qcom,mdss_dsi@0 {

		compatible = "qcom,mdss-dsi";

		hw-config = "single_dsi";

		pll-src-config = "PLL0";

		#address-cells = <1>;

		#size-cells = <1>;

		vdda-supply = <&pm8226_l4>;

		vcca-supply = <&pm8226_l28>;

		reg = <0x1a98000 0x1a98000 0x25c

		      0x1a98500 0x1a98500 0x280

		      0x1a98780 0x1a98780 0x30

		      0x193e000 0x193e000 0x30>;

		qcom,dsi-clk-ln-recovery;

		qcom,core-supply-entries {

			#address-cells = <1>;

			#size-cells = <0>;

			qcom,core-supply-entry@0 {

				reg = <0>;

				qcom,supply-name = "gdsc";

				qcom,supply-min-voltage = <0>;

				qcom,supply-max-voltage = <0>;

				qcom,supply-enable-load = <0>;

				qcom,supply-disable-load = <0>;

				qcom,supply-ulp-load = <0>;

				qcom,supply-pre-on-sleep = <0>;

				qcom,supply-post-on-sleep = <0>;

				qcom,supply-pre-off-sleep = <0>;

				qcom,supply-post-off-sleep = <0>;

			};

		};

		qcom,phy-supply-entries {

			#address-cells = <1>;

			#size-cells = <0>;

			qcom,phy-supply-entry@0 {

				reg = <0>;

				qcom,supply-name = "vddio";

				qcom,supply-min-voltage = <1800000>;

				qcom,supply-max-voltage = <1800000>;

				qcom,supply-enable-load = <100000>;

				qcom,supply-disable-load = <100>;

				qcom,supply-ulp-load = <100>;

				qcom,supply-pre-on-sleep = <0>;

				qcom,supply-post-on-sleep = <20>;

				qcom,supply-pre-off-sleep = <0>;

				qcom,supply-post-off-sleep = <0>;

			};

		};

		qcom,ctrl-supply-entries {

			#address-cells = <1>;

			#size-cells = <0>;

			qcom,ctrl-supply-entry@0 {

				reg = <0>;

				qcom,supply-name = "vdda";

				qcom,supply-min-voltage = <1200000>;

				qcom,supply-max-voltage = <1200000>;

				qcom,supply-enable-load = <100000>;

				qcom,supply-disable-load = <100>;

				qcom,supply-ulp-load = <1000>;

				qcom,supply-pre-on-sleep = <0>;

				qcom,supply-post-on-sleep = <20>;

				qcom,supply-pre-off-sleep = <0>;

				qcom,supply-post-off-sleep = <0>;

			};

		};

		mdss_dsi0: mdss_dsi_ctrl0@fd922800 {

			compatible = "qcom,mdss-dsi-ctrl";

			label = "MDSS DSI CTRL->0";

			cell-index = <0>;

			reg = 	<0xfd922800 0x1f8>,

				<0xfd922b00 0x2b0>,

				<0xfd998780 0x30>,

				<0xfd828000 0x108>;

			reg-names = "dsi_ctrl", "dsi_phy",

				"dsi_phy_regulator", "mmss_misc_phys";

			vdd-supply = <&pm8226_l15>;

			vddio-supply = <&pm8226_l8>;

			qcom,mdss-fb-map-prim = <&mdss_fb0>;

			qcom,mdss-mdp = <&mdss_mdp>;

			qcom,dsi-pref-prim-pan = <&dsi_tosh_720_vid>;

			qcom,platform-strength-ctrl = [ff 06];

			qcom,platform-bist-ctrl = [00 00 b1 ff 00 00];

			qcom,platform-regulator-settings = [07 09 03 00 20 00 01];

			qcom,platform-lane-config = [00 00 00 00 00 00 00 01 97

				00 00 00 00 05 00 00 01 97

				00 00 00 00 0a 00 00 01 97

				00 00 00 00 0f 00 00 01 97

				00 c0 00 00 00 00 00 01 bb];

			qcom,mmss-ulp-clamp-ctrl-offset = <0x20>;

			qcom,mmss-phyreset-ctrl-offset = <0x24>;

			qcom,regulator-ldo-mode;

			qcom,null-insertion-enabled;

			qcom,timing-db-mode;

			pinctrl-names = "mdss_default", "mdss_sleep";

			pinctrl-0 = <&mdss_dsi_active>;

			pinctrl-1 = <&mdss_dsi_suspend>;

			qcom,platform-reset-gpio = <&msmgpio 25 1>;

			qcom,platform-te-gpio = <&msmgpio 24 0>;

			qcom,platform-enable-gpio = <&msmgpio 58 1>;

			qcom,platform-bklight-en-gpio = <&msmgpio 86 0>;

			qcom,platform-mode-gpio = <&msmgpio 7 0>;

			qcom,platform-intf-mux-gpio = <&tlmm 115 0>;

			qcom,dsi-irq-line;

			qcom,lane-map = "lane_map_3012";

			qcom,display-id = "primary";

			qcom,bridge-index = <00>;

	        };

	};