Merge "ARM: dts: msm: modify the panel setting for SM8150 QRD device" into msm-4.14 (d2fd6227) · Commits · e / devices / android_kernel_oneplus_sm8150

arch/arm64/boot/dts/qcom/dsi-panel-sw43404-amoled-dsc-wqhd-cmd.dtsi

+2 −3

Original line number	Diff line number	Diff line
		@@ -33,7 +33,7 @@
		qcom,mdss-dsi-dma-trigger = "trigger_sw";
		qcom,mdss-dsi-mdp-trigger = "none";
		qcom,mdss-dsi-reset-sequence = <1 10>, <0 10>, <1 10>;
		qcom,mdss-dsi-bl-max-level = <255>;
		qcom,mdss-dsi-bl-max-level = <1023>;
		qcom,mdss-dsi-te-pin-select = <1>;
		qcom,mdss-dsi-wr-mem-start = <0x2c>;
		qcom,mdss-dsi-wr-mem-continue = <0x3c>;
		@@ -80,8 +80,7 @@
		05 01 00 00 1e 00 02 11 00
		39 01 00 00 00 00 03 b0 a5 00
		05 01 00 00 78 00 02 35 00
		05 01 00 00 00 00 02 29 00
		39 01 00 00 3c 00 03 51 80 03
		05 01 00 00 3c 00 02 29 00
		];

		qcom,mdss-dsi-off-command = [

+1 −1

Original line number	Diff line number	Diff line
		@@ -160,7 +160,7 @@
		qcom,panel-supply-entries = <&dsi_panel_pwr_supply_vdd_no_labibb>;
		qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
		qcom,mdss-dsi-bl-min-level = <1>;
		qcom,mdss-dsi-bl-max-level = <255>;
		qcom,mdss-dsi-bl-max-level = <1023>;
		qcom,mdss-dsi-mode-sel-gpio-state = "single_port";
		qcom,panel-mode-gpio = <&tlmm 7 0>;
		qcom,platform-te-gpio = <&tlmm 8 0>;

+8 −1

Original line number	Diff line number	Diff line
		@@ -760,11 +760,18 @@
		&dsi_sw43404_amoled_cmd {
		qcom,mdss-dsi-t-clk-post = <0x16>;
		qcom,mdss-dsi-t-clk-pre = <0x16>;
		qcom,esd-check-enabled;
		qcom,mdss-dsi-panel-status-check-mode = "reg_read";
		qcom,mdss-dsi-panel-status-command = [06 01 00 01 00 00 01 0a];
		qcom,mdss-dsi-panel-status-command-state = "dsi_lp_mode";
		qcom,mdss-dsi-panel-status-value = <0x9c>;
		qcom,mdss-dsi-panel-on-check-value = <0x9c>;
		qcom,mdss-dsi-panel-status-read-length = <1>;
		qcom,mdss-dsi-display-timings {
		timing@0 {
		qcom,mdss-dsi-panel-phy-timings = [00 1a 07 06 22 21 07
		07 04 03 04 00 16 16];
		qcom,display-topology = <2 2 1>;
		qcom,display-topology = <1 1 1>;
		qcom,default-topology-index = <0>;
		};
		};