Donate to e Foundation | Murena handsets with /e/OS | Own a part of Murena! Learn more

Commit b73c3d77 authored by Robert P. J. Day's avatar Robert P. J. Day Committed by James Bottomley
Browse files

[SCSI] Remove some unused SCSI-related kernel config variables. 



Remove the unused SCSI-related kernel config variables

	SCSI_NCR53C8XX_PROFILE_SUPPORT
	SCSI_NCR53C8XX_PROFILE
	53C700_IO_MAPPED
	AIC79XX_ENABLE_RD_STRM
	AIC7XXX_PROBE_EISA_VL

Signed-off-by: default avatarRobert P. J. Day <rpjday@mindspring.com>
Signed-off-by: default avatarAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: default avatarJames Bottomley <James.Bottomley@SteelEye.com>
parent 0d06b281

Documentation/scsi/ncr53c8xx.txt

+0 −5
Original line number Diff line number Diff line
@@ -562,11 +562,6 @@ if only one has a flaw for some SCSI feature, you can disable the 
support by the driver of this feature at linux start-up and enable

this feature after boot-up only for devices that support it safely.



CONFIG_SCSI_NCR53C8XX_PROFILE_SUPPORT  (default answer: n)

    This option must be set for profiling information to be gathered 

    and printed out through the proc file system. This features may 

    impact performances.



CONFIG_SCSI_NCR53C8XX_IOMAPPED       (default answer: n)

    Answer "y" if you suspect your mother board to not allow memory mapped I/O.

    May slow down performance a little.  This option is required by

drivers/scsi/Kconfig

+0 −16
Original line number Diff line number Diff line
@@ -1200,17 +1200,6 @@ config SCSI_NCR53C8XX_SYNC 
	  There is no safe option other than using good cabling, right

	  terminations and SCSI conformant devices.



config SCSI_NCR53C8XX_PROFILE

	bool "enable profiling"

	depends on SCSI_ZALON || SCSI_NCR_Q720

	help

	  This option allows you to enable profiling information gathering.

	  These statistics are not very accurate due to the low frequency

	  of the kernel clock (100 Hz on i386) and have performance impact

	  on systems that use very fast devices.



	  The normal answer therefore is N.



config SCSI_NCR53C8XX_NO_DISCONNECT

	bool "not allow targets to disconnect"

	depends on (SCSI_ZALON || SCSI_NCR_Q720) && SCSI_NCR53C8XX_DEFAULT_TAGS=0
@@ -1340,11 +1329,6 @@ config SCSI_SIM710 


	  It currently supports Compaq EISA cards and NCR MCA cards



config 53C700_IO_MAPPED

	bool

	depends on SCSI_SIM710

	default y



config SCSI_SYM53C416

	tristate "Symbios 53c416 SCSI support"

	depends on ISA && SCSI

drivers/scsi/aic7xxx/Kconfig.aic79xx

+0 −12
Original line number Diff line number Diff line
@@ -57,18 +57,6 @@ config AIC79XX_BUILD_FIRMWARE 
	or modify the assembler Makefile or the files it includes if your

	build environment is different than that of the author.



config AIC79XX_ENABLE_RD_STRM

	bool "Enable Read Streaming for All Targets"

	depends on SCSI_AIC79XX

	default n

	help

	Read Streaming is a U320 protocol option that should enhance

	performance.  Early U320 drive firmware actually performs slower

	with read streaming enabled so it is disabled by default.  Read

	Streaming can be configured in much the same way as tagged queueing

	using the "rd_strm" command line option.  See

	drivers/scsi/aic7xxx/README.aic79xx for details.



config AIC79XX_DEBUG_ENABLE

	bool "Compile in Debugging Code"

	depends on SCSI_AIC79XX

drivers/scsi/aic7xxx/Kconfig.aic7xxx

+0 −10
Original line number Diff line number Diff line
@@ -50,16 +50,6 @@ config AIC7XXX_RESET_DELAY_MS 


	Default: 5000 (5 seconds)



config AIC7XXX_PROBE_EISA_VL

	bool "Probe for EISA and VL AIC7XXX Adapters"

	depends on SCSI_AIC7XXX && EISA

	help

	Probe for EISA and VLB Aic7xxx controllers.  In many newer systems,

	the invasive probes necessary to detect these controllers can cause

	other devices to fail.  For this reason, the non-PCI probe code is

	disabled by default.  The current value of this option can be "toggled"

	via the no_probe kernel command line option.



config AIC7XXX_BUILD_FIRMWARE

	bool "Build Adapter Firmware with Kernel Build"

	depends on SCSI_AIC7XXX && !PREVENT_FIRMWARE_BUILD