Donate to e Foundation | Murena handsets with /e/OS | Own a part of Murena! Learn more

Commit 78f8c5bd authored by Yulei Yao's avatar Yulei Yao
Browse files

ARM: dts: msm: Enable camera on SM6150 QRD 



Add device node entries to enable camera
sensors on SM6150 QRD

Change-Id: I3a2e32fbfcfe9c88209d5014f90ffb09fca5180e
Signed-off-by: default avatarYulei Yao <yuleiy@codeaurora.org>
parent 045e3d6e

arch/arm64/boot/dts/qcom/sm6150-camera-sensor-qrd.dtsi

0 → 100644
+363 −0
Original line number Diff line number Diff line 
/*

 * Copyright (c) 2018, The Linux Foundation. All rights reserved.

 *

 * This program is free software; you can redistribute it and/or modify

 * it under the terms of the GNU General Public License version 2 and

 * only version 2 as published by the Free Software Foundation.

 *

 * This program is distributed in the hope that it will be useful,

 * but WITHOUT ANY WARRANTY; without even the implied warranty of

 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the

 * GNU General Public License for more details.

 */



#include <dt-bindings/clock/qcom,camcc-sm6150.h>



&soc {



	led_flash_rear: qcom,camera-flash@0 {

		cell-index = <0>;

		reg = <0x00 0x00>;

		compatible = "qcom,camera-flash";

		flash-source = <&pm6150l_flash0>;

		torch-source = <&pm6150l_torch1>;

		switch-source = <&pm6150l_switch0>;

		status = "ok";

	};



	led_flash_rear_aux: qcom,camera-flash@1 {

		cell-index = <1>;

		reg = <0x01 0x00>;

		compatible = "qcom,camera-flash";

		flash-source = <&pm6150l_flash1>;

		torch-source = <&pm6150l_torch1>;

		switch-source = <&pm6150l_switch1>;

		status = "ok";

	};



	led_flash_front: qcom,camera-flash@2 {

		cell-index = <2>;

		reg = <0x02 0x00>;

		compatible = "qcom,camera-flash";

		flash-source = <&pm6150l_flash2>;

		torch-source = <&pm6150l_torch2>;

		switch-source = <&pm6150l_switch2>;

		status = "ok";

		enable-active-high;

		gpio = <&tlmm 38 0>;

		pinctrl-names = "default";

		pinctrl-0 = <&flash_led3_front_en>;

	};



	camera_ldo: gpio-regulator@0 {

		compatible = "regulator-fixed";

		reg = <0x00 0x00>;

		regulator-name = "camera_ldo";

		regulator-min-microvolt = <1200000>;

		regulator-max-microvolt = <1200000>;

		regulator-enable-ramp-delay = <135>;

		enable-active-high;

		gpio = <&pm6150l_gpios 3 0>;

		pinctrl-names = "default";

		pinctrl-0 = <&cam_sensor_dvdd_en>;

		vin-supply = <&pm6150l_s8>;

	};



	camera_vana0_ldo: gpio-regulator@1 {

		compatible = "regulator-fixed";

		reg = <0x01 0x00>;

		regulator-name = "camera_vana0_ldo";

		regulator-min-microvolt = <2850000>;

		regulator-max-microvolt = <2850000>;

		regulator-enable-ramp-delay = <233>;

		enable-active-high;

		gpio = <&pm6150l_gpios 9 0>;

		pinctrl-names = "default";

		pinctrl-0 = <&cam_sensor_0_vana>;

		vin-supply = <&pm6150l_bob>;

	};



	camera_vana1_2_ldo: gpio-regulator@2 {

		compatible = "regulator-fixed";

		reg = <0x02 0x00>;

		regulator-name = "camera_vana1_2_ldo";

		regulator-min-microvolt = <2850000>;

		regulator-max-microvolt = <2850000>;

		regulator-enable-ramp-delay = <233>;

		enable-active-high;

		gpio = <&pm6150l_gpios 4 0>;

		pinctrl-names = "default";

		pinctrl-0 = <&cam_sensor_1_2_vana>;

		vin-supply = <&pm6150l_bob>;

	};

};



&cam_cci {

	qcom,cam-res-mgr {

		compatible = "qcom,cam-res-mgr";

		status = "ok";

	};



	actuator_rear: qcom,actuator@0 {

		cell-index = <0>;

		reg = <0x0>;

		compatible = "qcom,actuator";

		cci-master = <0>;

		cam_vaf-supply = <&pm6150_l19>;

		regulator-names = "cam_vaf";

		rgltr-cntrl-support;

		rgltr-min-voltage = <2800000>;

		rgltr-max-voltage = <2800000>;

		rgltr-load-current = <0>;

	};



	actuator_front: qcom,actuator@1 {

		cell-index = <1>;

		reg = <0x1>;

		compatible = "qcom,actuator";

		cci-master = <1>;

		cam_vaf-supply = <&pm6150_l19>;

		regulator-names = "cam_vaf";

		rgltr-cntrl-support;

		rgltr-min-voltage = <2800000>;

		rgltr-max-voltage = <2800000>;

		rgltr-load-current = <0>;

	};



	eeprom_rear: qcom,eeprom@0 {

		cell-index = <0>;

		reg = <0>;

		compatible = "qcom,eeprom";

		cam_vio-supply = <&pm6150_l13>;

		cam_vana-supply = <&camera_vana0_ldo>;

		cam_vdig-supply = <&camera_ldo>;

		cam_clk-supply = <&titan_top_gdsc>;

		cam_vaf-supply = <&pm6150_l19>;

		regulator-names = "cam_vio", "cam_vana", "cam_vdig",

			"cam_clk", "cam_vaf";

		rgltr-cntrl-support;

		rgltr-min-voltage = <1800000 2850000 1200000 0 2800000>;

		rgltr-max-voltage = <1800000 2850000 1200000 0 2800000>;

		rgltr-load-current = <0 80000 105000 0 0>;

		gpio-no-mux = <0>;

		pinctrl-names = "cam_default", "cam_suspend";

		pinctrl-0 = <&cam_sensor_mclk0_active

				&cam_sensor_rear_active>;

		pinctrl-1 = <&cam_sensor_mclk0_suspend

				&cam_sensor_rear_suspend>;

		gpios = <&tlmm 28 0>,

			<&tlmm 47 0>;

		gpio-reset = <1>;

		gpio-req-tbl-num = <0 1>;

		gpio-req-tbl-flags = <1 0>;

		gpio-req-tbl-label = "CAMIF_MCLK0",

					"CAM_RESET0";

		sensor-mode = <0>;

		cci-master = <0>;

		status = "ok";

		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;

		clock-names = "cam_clk";

		clock-cntl-level = "turbo";

		clock-rates = <24000000>;

	};



	eeprom_rear_aux: qcom,eeprom@1 {

		cell-index = <1>;

		reg = <0x1>;

		compatible = "qcom,eeprom";

		cam_vio-supply = <&pm6150_l13>;

		cam_vana-supply = <&camera_vana1_2_ldo>;

		cam_vdig-supply = <&camera_ldo>;

		cam_clk-supply = <&titan_top_gdsc>;

		cam_vaf-supply = <&pm6150_l19>;

		regulator-names = "cam_vio", "cam_vana", "cam_vdig",

			"cam_clk", "cam_vaf";

		rgltr-cntrl-support;

		rgltr-min-voltage = <1800000 2850000 1200000 0 2800000>;

		rgltr-max-voltage = <1800000 2850000 1200000 0 2800000>;

		rgltr-load-current = <105000 0 80000 0 0>;

		gpio-no-mux = <0>;

		pinctrl-names = "cam_default", "cam_suspend";

		pinctrl-0 = <&cam_sensor_mclk1_active

				&cam_sensor_rear2_active>;

		pinctrl-1 = <&cam_sensor_mclk1_suspend

				&cam_sensor_rear2_suspend>;

		gpios = <&tlmm 29 0>,

			<&tlmm 45 0>;

		gpio-reset = <1>;

		gpio-req-tbl-num = <0 1>;

		gpio-req-tbl-flags = <1 0>;

		gpio-req-tbl-label = "CAMIF_MCLK1",

					"CAM_RESET1";

		sensor-position = <0>;

		sensor-mode = <0>;

		cci-master = <0>;

		status = "ok";

		clock-names = "cam_clk";

		clock-cntl-level = "turbo";

		clock-rates = <24000000>;

	};



	eeprom_front: qcom,eeprom@2 {

		cell-index = <2>;

		reg = <0x2>;

		compatible = "qcom,eeprom";

		cam_vio-supply = <&pm6150_l13>;

		cam_vana-supply = <&camera_vana1_2_ldo>;

		cam_vdig-supply = <&camera_ldo>;

		cam_clk-supply = <&titan_top_gdsc>;

		cam_vaf-supply = <&pm6150_l19>;

		regulator-names = "cam_vio", "cam_vana", "cam_vdig",

			"cam_clk", "cam_vaf";

		rgltr-cntrl-support;

		rgltr-min-voltage = <1800000 2850000 1200000 0 2800000>;

		rgltr-max-voltage = <1800000 2850000 1200000 0 2800000>;

		rgltr-load-current = <0 80000 105000 0 0>;

		gpio-no-mux = <0>;

		pinctrl-names = "cam_default", "cam_suspend";

		pinctrl-0 = <&cam_sensor_mclk2_active

				 &cam_sensor_front_active>;

		pinctrl-1 = <&cam_sensor_mclk2_suspend

				 &cam_sensor_front_suspend>;

		gpios = <&tlmm 30 0>,

			<&tlmm 37 0>;

		gpio-reset = <1>;

		gpio-req-tbl-num = <0 1>;

		gpio-req-tbl-flags = <1 0>;

		gpio-req-tbl-label = "CAMIF_MCLK2",

					"CAM_RESET2";

		sensor-mode = <0>;

		cci-master = <1>;

		status = "ok";

		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;

		clock-names = "cam_clk";

		clock-cntl-level = "turbo";

		clock-rates = <24000000>;

	};



	qcom,cam-sensor@0 {

		cell-index = <0>;

		compatible = "qcom,cam-sensor";

		reg = <0x0>;

		csiphy-sd-index = <0>;

		sensor-position-roll = <90>;

		sensor-position-pitch = <0>;

		sensor-position-yaw = <180>;

		actuator-src = <&actuator_rear>;

		led-flash-src = <&led_flash_rear>;

		eeprom-src = <&eeprom_rear>;

		cam_vio-supply = <&pm6150_l13>;

		cam_vana-supply = <&camera_vana0_ldo>;

		cam_vdig-supply = <&camera_ldo>;

		cam_clk-supply = <&titan_top_gdsc>;

		regulator-names = "cam_vio", "cam_vana", "cam_vdig",

			"cam_clk";

		rgltr-cntrl-support;

		rgltr-min-voltage = <1800000 2850000 1200000 0>;

		rgltr-max-voltage = <1800000 2850000 1200000 0>;

		rgltr-load-current = <0 80000 105000 0>;

		gpio-no-mux = <0>;

		pinctrl-names = "cam_default", "cam_suspend";

		pinctrl-0 = <&cam_sensor_mclk0_active

				&cam_sensor_rear_active>;

		pinctrl-1 = <&cam_sensor_mclk0_suspend

				&cam_sensor_rear_suspend>;

		gpios = <&tlmm 28 0>,

			<&tlmm 47 0>;

		gpio-reset = <1>;

		gpio-req-tbl-num = <0 1>;

		gpio-req-tbl-flags = <1 0>;

		gpio-req-tbl-label = "CAMIF_MCLK0",

					"CAM_RESET0";

		sensor-mode = <0>;

		cci-master = <0>;

		status = "ok";

		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;

		clock-names = "cam_clk";

		clock-cntl-level = "turbo";

		clock-rates = <24000000>;

	};



	qcom,cam-sensor@1 {

		cell-index = <1>;

		compatible = "qcom,cam-sensor";

		reg = <0x1>;

		csiphy-sd-index = <1>;

		sensor-position-roll = <90>;

		sensor-position-pitch = <0>;

		sensor-position-yaw = <180>;

		led-flash-src = <&led_flash_rear>;

		cam_vio-supply = <&pm6150_l13>;

		cam_vana-supply = <&camera_vana1_2_ldo>;

		cam_vdig-supply = <&camera_ldo>;

		cam_clk-supply = <&titan_top_gdsc>;

		regulator-names = "cam_vio", "cam_vana", "cam_vdig",

			"cam_clk";

		rgltr-cntrl-support;

		rgltr-min-voltage = <1800000 2850000 1200000 0>;

		rgltr-max-voltage = <1800000 2850000 1200000 0>;

		rgltr-load-current = <0 80000 105000 0>;

		gpio-no-mux = <0>;

		pinctrl-names = "cam_default", "cam_suspend";

		pinctrl-0 = <&cam_sensor_mclk1_active

				&cam_sensor_rear2_active>;

		pinctrl-1 = <&cam_sensor_mclk1_suspend

				&cam_sensor_rear2_suspend>;

		gpios = <&tlmm 29 0>,

			<&tlmm 45 0>;

		gpio-reset = <1>;

		gpio-req-tbl-num = <0 1>;

		gpio-req-tbl-flags = <1 0>;

		gpio-req-tbl-label = "CAMIF_MCLK1",

					"CAM_RESET1";

		sensor-mode = <0>;

		cci-master = <0>;

		status = "ok";

		clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;

		clock-names = "cam_clk";

		clock-cntl-level = "turbo";

		clock-rates = <24000000>;

	};



	qcom,cam-sensor@2 {

		cell-index = <2>;

		compatible = "qcom,cam-sensor";

		reg = <0x02>;

		csiphy-sd-index = <2>;

		sensor-position-roll = <270>;

		sensor-position-pitch = <0>;

		sensor-position-yaw = <0>;

		actuator-src = <&actuator_front>;

		eeprom-src = <&eeprom_front>;

		cam_vio-supply = <&pm6150_l13>;

		cam_vana-supply = <&camera_vana1_2_ldo>;

		cam_vdig-supply = <&camera_ldo>;

		cam_clk-supply = <&titan_top_gdsc>;

		regulator-names = "cam_vio", "cam_vana", "cam_vdig",

			"cam_clk";

		rgltr-cntrl-support;

		rgltr-min-voltage = <1800000 2850000 1200000 0>;

		rgltr-max-voltage = <1800000 2850000 1200000 0>;

		rgltr-load-current = <0 80000 105000 0>;

		gpio-no-mux = <0>;

		pinctrl-names = "cam_default", "cam_suspend";

		pinctrl-0 = <&cam_sensor_mclk2_active

				 &cam_sensor_front_active>;

		pinctrl-1 = <&cam_sensor_mclk2_suspend

				 &cam_sensor_front_suspend>;

		gpios = <&tlmm 30 0>,

			<&tlmm 37 0>;

		gpio-reset = <1>;

		gpio-req-tbl-num = <0 1>;

		gpio-req-tbl-flags = <1 0>;

		gpio-req-tbl-label = "CAMIF_MCLK2",

					"CAM_RESET2";

		sensor-mode = <0>;

		cci-master = <1>;

		status = "ok";

		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;

		clock-names = "cam_clk";

		clock-cntl-level = "turbo";

		clock-rates = <24000000>;

	};

};

arch/arm64/boot/dts/qcom/sm6150-qrd.dtsi

+1 −0
Original line number Diff line number Diff line
@@ -13,6 +13,7 @@ 
#include "sm6150-thermal-overlay.dtsi"

#include <dt-bindings/iio/qcom,spmi-vadc.h>

#include "sm6150-sde-display.dtsi"

#include "sm6150-camera-sensor-qrd.dtsi"



&soc {

};