Donate to e Foundation | Murena handsets with /e/OS | Own a part of Murena! Learn more

Commit 6b7f06cc authored by Srinivas Kandagatla's avatar Srinivas Kandagatla
Browse files

ARM: STi: STiH415: Add reset controller support. 



This patch adds a reset controller node to the SOC device tree and also
adds new header files with reset lines required for other device tree
nodes.

Signed-off-by: default avatarSrinivas Kandagatla <srinivas.kandagatla@st.com>
parent 7ec5183a

Documentation/devicetree/bindings/reset/st,sti-powerdown.txt

0 → 100644
+47 −0
Original line number Diff line number Diff line 
STMicroelectronics STi family Sysconfig Peripheral Powerdown Reset Controller

=============================================================================



This binding describes a reset controller device that is used to enable and

disable on-chip peripheral controllers such as USB and SATA, using

"powerdown" control bits found in the STi family SoC system configuration

registers. These have been grouped together into a single reset controller

device for convenience.



The actual action taken when powerdown is asserted is hardware dependent.

However, when asserted it may not be possible to access the hardware's

registers and after an assert/deassert sequence the hardware's previous state

may no longer be valid.



Please refer to reset.txt in this directory for common reset

controller binding usage.



Required properties:

- compatible: Should be "st,<chip>-powerdown"

	ex: "st,stih415-powerdown", "st,stih416-powerdown"

- #reset-cells: 1, see below



example:



	powerdown: powerdown-controller {

		#reset-cells = <1>;

		compatible = "st,stih415-powerdown";

	};





Specifying powerdown control of devices

=======================================



Device nodes should specify the reset channel required in their "resets"

property, containing a phandle to the powerdown device node and an

index specifying which channel to use, as described in reset.txt



example:



	usb1: usb@fe200000 {

		resets	= <&powerdown STIH41X_USB1_POWERDOWN>;

	};



Macro definitions for the supported reset channels can be found in:



include/dt-bindings/reset-controller/stih415-resets.h

include/dt-bindings/reset-controller/stih416-resets.h

arch/arm/boot/dts/stih415.dtsi

+6 −0
Original line number Diff line number Diff line
@@ -10,6 +10,7 @@ 
#include "stih415-clock.dtsi"

#include "stih415-pinctrl.dtsi"

#include <dt-bindings/interrupt-controller/arm-gic.h>

#include <dt-bindings/reset-controller/stih415-resets.h>

/ {



	L2: cache-controller {
@@ -28,6 +29,11 @@ 
		ranges;

		compatible	= "simple-bus";



		powerdown: powerdown-controller {

			#reset-cells = <1>;

			compatible = "st,stih415-powerdown";

		};



		syscfg_sbc: sbc-syscfg@fe600000{

			compatible      = "st,stih415-sbc-syscfg", "syscon";

			reg		= <0xfe600000 0xb4>;

include/dt-bindings/reset-controller/stih415-resets.h

0 → 100644
+19 −0
Original line number Diff line number Diff line 
/*

 * This header provides constants for the reset controller

 * based peripheral powerdown requests on the STMicroelectronics

 * STiH415 SoC.

 */

#ifndef _DT_BINDINGS_RESET_CONTROLLER_STIH415

#define _DT_BINDINGS_RESET_CONTROLLER_STIH415



#define STIH415_EMISS_POWERDOWN		0

#define STIH415_NAND_POWERDOWN		1

#define STIH415_KEYSCAN_POWERDOWN	2

#define STIH415_USB0_POWERDOWN		3

#define STIH415_USB1_POWERDOWN		4

#define STIH415_USB2_POWERDOWN		5

#define STIH415_SATA0_POWERDOWN		6

#define STIH415_SATA1_POWERDOWN		7

#define STIH415_PCIE_POWERDOWN		8



#endif /* _DT_BINDINGS_RESET_CONTROLLER_STIH415 */