hwmon/w83793: Add documentation and maintainer

****************

temp[1-*]_type	Sensor type selection.

		Integers 1 to 4 or thermistor Beta value (typically 3435)

		Integers 1 to 6 or thermistor Beta value (typically 3435)

		RW

		1: PII/Celeron Diode

		2: 3904 transistor

		3: thermal diode

		4: thermistor (default/unknown Beta)

		5: AMD AMDSI

		6: Intel PECI

		Not all types are supported by all chips

temp[1-*]_max	Temperature max value.

Kernel driver w83793

====================

Supported chips:

  * Winbond W83793G/W83793R

    Prefix: 'w83793'

    Addresses scanned: I2C 0x2c - 0x2f

    Datasheet: Still not published

Authors:

    Yuan Mu (Winbond Electronics)

    Rudolf Marek <r.marek@assembler.cz>

Module parameters

-----------------

* reset int

  (default 0)

  This parameter is not recommended, it will lose motherboard specific

  settings. Use 'reset=1' to reset the chip when loading this module.

* force_subclients=bus,caddr,saddr1,saddr2

  This is used to force the i2c addresses for subclients of

  a certain chip. Typical usage is `force_subclients=0,0x2f,0x4a,0x4b'

  to force the subclients of chip 0x2f on bus 0 to i2c addresses

  0x4a and 0x4b.

Description

-----------

This driver implements support for Winbond W83793G/W83793R chips.

* Exported features

  This driver exports 10 voltage sensors, up to 12 fan tachometer inputs,

  6 remote temperatures, up to 8 sets of PWM fan controls, SmartFan

  (automatic fan speed control) on all temperature/PWM combinations, 2

  sets of 6-pin CPU VID input.

* Sensor resolutions

  If your motherboard maker used the reference design, the resolution of

  voltage0-2 is 2mV, resolution of voltage3/4/5 is 16mV, 8mV for voltage6,

  24mV for voltage7/8. Temp1-4 have a 0.25 degree Celsius resolution,

  temp5-6 have a 1 degree Celsiis resolution.

* Temperature sensor types

  Temp1-4 have 3 possible types. It can be read from (and written to)

  temp[1-4]_type.

  - If the value of 0, the related temperature channel stops

    monitoring.

  - If the value is 3, it starts monitoring using a remote termal diode

    (default).

  - If the value is 5, it starts monitoring using the temperature sensor

    in AMD CPU and get result by AMDSI.

  - If the value is 6, it starts monitoring using the temperature sensor

    in Intel CPU and get result by PECI.

  Temp5-6 can be connected to external thermistors (value of

  temp[5-6]_type is 4). They can also be disabled (value is 0).

* Alarm mechanism

  For voltage sensors, an alarm triggers if the measured value is below

  the low voltage limit or over the high voltage limit.

  For temperature sensors, an alarm triggers if the measured value goes

  above the high temperature limit, and wears off only after the measured

  value drops below the hysteresis value.

  For fan sensors, an alarm triggers if the measured value is below the

  low speed limit.

* SmartFan/PWM control

  If you want to set a pwm fan to manual mode, you just need to make sure it

  is not controlled by any temp channel, for example, you want to set fan1

  to manual mode, you need to check the value of temp[1-6]_fan_map, make

  sure bit 0 is cleared in the 6 values. And then set the pwm1 value to

  control the fan.

  Each temperature channel can control all the 8 PWM outputs (by setting the

  corresponding bit in tempX_fan_map), you can set the temperature channel

  mode using temp[1-6]_pwm_enable, 2 is Thermal Cruise mode and 3

  is the SmartFanII mode. Temperature channels will try to speed up or

  slow down all controlled fans, this means one fan can receive different

  PWM value requests from different temperature channels, but the chip

  will always pick the safest (max) PWM value for each fan.

  In Thermal Cruise mode, the chip attempts to keep the temperature at a

  predefined value, within a tolerance margin. So if tempX_input >

  thermal_cruiseX + toleranceX, the chip will increase the PWM value,

  if tempX_input < thermal_cruiseX - toleranceX, the chip will decrease

  the PWM value. If the temperature is within the tolerance range, the PWM

  value is left unchanged.

  SmartFanII works differently, you have to define up to 7 PWM, temperature

  trip points, defining a PWM/temperature curve which the chip will follow.

  While not fundamentally different from the Thermal Cruise mode, the

  implementation is quite different, giving you a finer-grained control.

* Chassis

  If the case open alarm triggers, it will stay in this state unless cleared

  by any write to the sysfs file "chassis".

* VID and VRM

  The VRM version is detected automatically, don't modify the it unless you

  *do* know the cpu VRM version and it's not properly detected.

Notes

-----

  Only Fan1-5 and PWM1-3 are guaranteed to always exist, other fan inputs and

  PWM outputs may or may not exist depending on the chip pin configuration.

L:	lm-sensors@lm-sensors.org

S:	Maintained

W83793 HARDWARE MONITORING DRIVER

P:	Rudolf Marek

M:	r.marek@assembler.cz

L:	lm-sensors@lm-sensors.org

S:	Maintained

W83L51xD SD/MMC CARD INTERFACE DRIVER

P:	Pierre Ossman

M:	drzeus-wbsd@drzeus.cx