ARM: at91/dt: Add Support for the L+G VInCo platform (3869394a) · Commits · e / devices / android_kernel_oneplus_sm8150

arch/arm/boot/dts/Makefile

+2 −1

Original line number	Diff line number	Diff line
		@@ -50,7 +50,8 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
		sama5d36ek.dtb \
		at91-sama5d4_ma5d4evk.dtb \
		at91-sama5d4_xplained.dtb \
		at91-sama5d4ek.dtb
		at91-sama5d4ek.dtb \
		at91-vinco.dtb
		dtb-$(CONFIG_ARCH_ATLAS6) += \
		atlas6-evb.dtb
		dtb-$(CONFIG_ARCH_ATLAS7) += \

arch/arm/boot/dts/at91-vinco.dts

0 → 100644

+256 −0

Original line number	Diff line number	Diff line
		/*
		* Device Tree file for VInCo platform
		*
		* Copyright (C) 2014 Atmel,
		* 2014 Nicolas Ferre <nicolas.ferre@atmel.com>
		* 2015 Gregory CLEMENT <gregory.clement@free-electrons.com>
		*
		* This file is dual-licensed: you can use it either under the terms
		* of the GPL or the X11 license, at your option. Note that this dual
		* licensing only applies to this file, and not this project as a
		* whole.
		*
		* a) This file is free software; you can redistribute it and/or
		* modify it under the terms of the GNU General Public License as
		* published by the Free Software Foundation; either version 2 of the
		* License, or (at your option) any later version.
		*
		* This file is distributed in the hope that it will be useful,
		* but WITHOUT ANY WARRANTY; without even the implied warranty of
		* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
		* GNU General Public License for more details.
		*
		* Or, alternatively,
		*
		* b) Permission is hereby granted, free of charge, to any person
		* obtaining a copy of this software and associated documentation
		* files (the "Software"), to deal in the Software without
		* restriction, including without limitation the rights to use,
		* copy, modify, merge, publish, distribute, sublicense, and/or
		* sell copies of the Software, and to permit persons to whom the
		* Software is furnished to do so, subject to the following
		* conditions:
		*
		* The above copyright notice and this permission notice shall be
		* included in all copies or substantial portions of the Software.
		*
		* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
		* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
		* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
		* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
		* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
		* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
		* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
		* OTHER DEALINGS IN THE SOFTWARE.
		*/
		/dts-v1/;
		#include "sama5d4.dtsi"

		/ {
		model = "L+G VInCo platform";
		compatible = "l+g,vinco", "atmel,sama5d4", "atmel,sama5";

		chosen {
		stdout-path = "serial0:115200n8";
		};

		memory {
		reg = <0x20000000 0x4000000>;
		};

		clocks {
		slow_xtal {
		clock-frequency = <32768>;
		};

		main_xtal {
		clock-frequency = <12000000>;
		};
		};

		ahb {
		apb {

		adc0: adc@fc034000 {
		status = "okay"; /* Enable ADC IIO support */
		};

		mmc0: mmc@f8000000 {
		pinctrl-names = "default";
		pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0
		&pinctrl_mmc0_dat1_3
		&pinctrl_mmc0_dat4_7>;
		vqmmc-supply = <&vcc_3v3_reg>;
		vmmc-supply = <&vcc_3v3_reg>;
		no-1-8-v;
		status = "okay";
		slot@0 {
		reg = <0>;
		bus-width = <8>;
		non-removable;
		broken-cd;
		status = "okay";
		};
		};

		spi0: spi@f8010000 {
		cs-gpios = <&pioC 3 0>, <0>, <0>, <0>;
		status = "okay";
		m25p80@0 {
		compatible = "n25q32b", "jedec,spi-nor";
		spi-max-frequency = <50000000>;
		reg = <0>;
		};
		};

		i2c0: i2c@f8014000 {
		status = "okay";
		};

		i2c1: i2c@f8018000 {
		status = "okay";
		/* kerkey security module */
		};

		macb0: ethernet@f8020000 {
		phy-mode = "rmii";
		status = "okay";

		ethernet-phy@1 {
		reg = <0x1>;
		reset-gpios = <&pioE 8 GPIO_ACTIVE_HIGH>;
		interrupt-parent = <&pioB>;
		interrupts = <15 IRQ_TYPE_EDGE_FALLING>;
		};

		};

		i2c2: i2c@f8024000 {
		status = "okay";

		rtc1: rtc@64 {
		compatible = "epson,rx8900";
		reg = <0x32>;
		};
		};

		usart2: serial@fc008000 {
		/* MBUS */
		status = "okay";
		};

		usart3: serial@fc00c000 {
		/* debug */
		status = "okay";
		};

		usart4: serial@fc010000 {
		/* LMN */
		pinctrl-0 = <&pinctrl_usart4 &pinctrl_usart4_rts>;
		linux,rs485-enabled-at-boot-time;
		status = "okay";
		};

		macb1: ethernet@fc028000 {
		phy-mode = "rmii";
		status = "okay";
		#address-cells = <1>;
		#size-cells = <0>;
		status = "okay";

		ethernet-phy@1 {
		reg = <0x1>;
		interrupt-parent = <&pioB>;
		interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
		reset-gpios = <&pioE 6 GPIO_ACTIVE_HIGH>;
		};
		};

		watchdog@fc068640 {
		status = "okay";
		};

		pinctrl@fc06a000 {
		board {
		pinctrl_usba_vbus: usba_vbus {
		atmel,pins =
		<AT91_PIOE 31 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
		};
		};
		};
		};

		usb0: gadget@00400000 {
		atmel,vbus-gpio = <&pioE 31 GPIO_ACTIVE_HIGH>;
		pinctrl-names = "default";
		pinctrl-0 = <&pinctrl_usba_vbus>;
		status = "disable";
		};

		usb1: ohci@00500000 {
		num-ports = <3>;
		atmel,vbus-gpio = <0
		&pioE 11 GPIO_ACTIVE_LOW
		&pioE 12 GPIO_ACTIVE_LOW
		>;
		status = "disable";
		};

		usb2: ehci@00600000 {
		/* 4G Modem */
		status = "okay";
		};

		};

		leds {
		compatible = "gpio-leds";
		status = "okay";

		led_err {
		label = "err";
		gpios = <&pioA 7 GPIO_ACTIVE_LOW>;
		default-state = "off";
		};

		led_rssi {
		label = "rssi";
		gpios = <&pioA 9 GPIO_ACTIVE_LOW>;
		default-state = "off";
		};

		led_tls {
		label = "tls";
		gpios = <&pioA 24 GPIO_ACTIVE_LOW>;
		default-state = "off";
		};

		led_lmc {
		label = "lmc";
		gpios = <&pioA 25 GPIO_ACTIVE_LOW>;
		default-state = "off";
		};

		led_wmt {
		label = "wmt";
		gpios = <&pioA 29 GPIO_ACTIVE_LOW>;
		default-state = "off";
		};

		led_pwr {
		label = "pwr";
		gpios = <&pioA 26 GPIO_ACTIVE_LOW>;
		default-state = "on";
		};

		};

		vcc_3v3_reg: fixedregulator@0 {
		compatible = "regulator-fixed";
		regulator-name = "VCC 3V3";
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;
		regulator-boot-on;
		regulator-always-on;
		};
		};