Merge "ARM: dts: msm: Add LT9611 support for QCS610" (35bfb444) · Commits · e / devices / android_kernel_oneplus_sm8150

arch/arm64/boot/dts/qcom/qcs610-iot-overlay.dts

+0 −4

Original line number	Diff line number	Diff line
		@@ -23,7 +23,3 @@
		qcom,msm-id = <401 0x0>;
		qcom,board-id = <32 0>;
		};

		&dsi_hx83112a_truly_vid_display {
		qcom,dsi-display-active;
		};

arch/arm64/boot/dts/qcom/qcs610-iot.dtsi

+101 −2

Original line number	Diff line number	Diff line
		@@ -14,8 +14,6 @@
		#include <dt-bindings/iio/qcom,spmi-vadc.h>
		#include <dt-bindings/input/input.h>
		#include "qcs610.dtsi"
		#include "sm6150-sde.dtsi"
		#include "sm6150-sde-pll.dtsi"
		#include "sm6150-sde-display.dtsi"
		#include "qcs610-camera-sensor-idp.dtsi"

		@@ -207,3 +205,104 @@
		qcom,platform-te-gpio = <&tlmm 90 0>;
		qcom,platform-reset-gpio = <&tlmm 91 0>;
		};

		&qupv3_se1_i2c {
		status = "ok";
		lt9611: lt,lt9611@3b {
		compatible = "lt,lt9611";
		reg = <0x3b>;
		interrupt-parent = <&tlmm>;
		interrupts = <26 0>;
		interrupt-names = "lt_irq";
		lt,irq-gpio = <&tlmm 26 0x0>;
		lt,reset-gpio = <&tlmm 20 0x0>;
		instance_id = <0>;
		lt,non-pluggable;
		lt,preferred-mode = "1920x1080";

		vdd-supply = <&pm6150_l13>;
		vcc-supply = <&pm6150_l16>;

		lt,supply-entries {
		#address-cells = <1>;
		#size-cells = <0>;

		lt,supply-entry@0 {
		reg = <0>;
		lt,supply-name = "vcc";
		lt,supply-min-voltage = <3304000>;
		lt,supply-max-voltage = <3304000>;
		lt,supply-enable-load = <200000>;
		lt,supply-post-on-sleep = <50>;
		};

		lt,supply-entry@1 {
		reg = <1>;
		lt,supply-name = "vdd";
		lt,supply-min-voltage = <1800000>;
		lt,supply-max-voltage = <1800000>;
		lt,supply-enable-load = <200000>;
		lt,supply-post-on-sleep = <50>;
		};
		};

		lt,customize-modes {
		lt,customize-mode-id@0 {
		lt,mode-h-active = <1920>;
		lt,mode-h-front-porch = <88>;
		lt,mode-h-pulse-width = <44>;
		lt,mode-h-back-porch = <148>;
		lt,mode-h-active-high;
		lt,mode-v-active = <1080>;
		lt,mode-v-front-porch = <4>;
		lt,mode-v-pulse-width = <5>;
		lt,mode-v-back-porch = <36>;
		lt,mode-v-active-high;
		lt,mode-refresh-rate = <60>;
		lt,mode-clock-in-khz = <148500>;
		};
		};

		ports {
		#address-cells = <1>;
		#size-cells = <0>;

		port@0 {
		reg = <0>;
		lt9611_in: endpoint {
		remote-endpoint = <&ext_dsi_out>;
		};
		};
		};
		};
		};


		&soc {
		ext_dsi_bridge_display: qcom,dsi-display@50 {
		label = "ext_dsi_bridge_display hdmi 1080p";
		qcom,dsi-display-active;
		qcom,display-type = "primary";

		qcom,dsi-ctrl-num = <0>;
		qcom,dsi-phy-num = <0>;
		qcom,dsi-select-clocks = "mux_byte_clk0", "mux_pixel_clk0";
		qcom,dsi-panel = <&dsi_ext_bridge_hdmi_1080p>;
		};
		};

		&sde_dsi {
		qcom,dsi-display-list = <&ext_dsi_bridge_display>;

		ports {
		#address-cells = <1>;
		#size-cells = <0>;

		port@0 {
		reg = <0>;
		ext_dsi_out: endpoint {
		remote-endpoint = <&lt9611_in>;
		};
		};
		};
		};

arch/arm64/boot/dts/qcom/sm6150-sde-display.dtsi

+19 −0

Original line number	Diff line number	Diff line
		@@ -20,6 +20,7 @@
		#include "dsi-panel-td4330-truly-singlemipi-fhd-cmd.dtsi"
		#include "dsi-panel-td4330-truly-singlemipi-fhd-video.dtsi"
		#include "dsi-panel-sharp-split-link-wuxga-video.dtsi"
		#include "dsi-panel-ext-bridge-hdmi-1080p.dtsi"
		#include <dt-bindings/clock/mdss-14nm-pll-clk.h>

		&soc {
		@@ -524,3 +525,21 @@
		};
		};
		};

		&dsi_ext_bridge_hdmi_1080p {
		qcom,mdss-dsi-t-clk-post = <0x0D>;
		qcom,mdss-dsi-t-clk-pre = <0x30>;
		qcom,mdss-dsi-display-timings {
		timing@0{
		qcom,mdss-dsi-panel-phy-timings =
		[24 1f 08 09 05 03 04 a0
		24 1f 08 09 05 03 04 a0
		24 1f 08 09 05 03 04 a0
		24 1f 08 09 05 03 04 a0
		24 1b 08 09 05 03 04 a0];

		qcom,display-topology = <1 0 1>;
		qcom,default-topology-index = <0>;
		};
		};
		};