ARM: dts: msm: Add PM6125 peripherals for trinket

/*

 * Copyright (c) 2018, The Linux Foundation. All rights reserved.

 *

 * This program is free software; you can redistribute it and/or modify

 * it under the terms of the GNU General Public License version 2 and

 * only version 2 as published by the Free Software Foundation.

 *

 * This program is distributed in the hope that it will be useful,

 * but WITHOUT ANY WARRANTY; without even the implied warranty of

 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the

 * GNU General Public License for more details.

 */

#include <dt-bindings/input/input.h>

#include <dt-bindings/input/qcom,qpnp-power-on.h>

#include <dt-bindings/interrupt-controller/irq.h>

#include <dt-bindings/spmi/spmi.h>

#include <dt-bindings/iio/qcom,spmi-vadc.h>

&spmi_bus {

	qcom,pm6125@0 {

		compatible = "qcom,spmi-pmic";

		reg = <0x0 SPMI_USID>;

		#address-cells = <1>;

		#size-cells = <1>;

		pm6125_revid: qcom,revid@100 {

			compatible = "qcom,qpnp-revid";

			reg = <0x100 0x100>;

		};

		qcom,power-on@800 {

			compatible = "qcom,qpnp-power-on";

			reg = <0x800 0x100>;

			interrupts = <0x0 0x8 0x0 IRQ_TYPE_NONE>,

				     <0x0 0x8 0x1 IRQ_TYPE_NONE>;

			interrupt-names = "kpdpwr", "resin";

			qcom,pon-dbc-delay = <15625>;

			qcom,kpdpwr-sw-debounce;

			qcom,system-reset;

			qcom,store-hard-reset-reason;

			qcom,pon_1 {

				qcom,pon-type = <PON_POWER_ON_TYPE_KPDPWR>;

				qcom,pull-up = <1>;

				linux,code = <KEY_POWER>;

			};

			qcom,pon_2 {

				qcom,pon-type = <PON_POWER_ON_TYPE_RESIN>;

				qcom,pull-up = <1>;

				linux,code = <KEY_VOLUMEDOWN>;

			};

		};

		pm6125_misc: qcom,misc@900 {

			compatible = "qcom,qpnp-misc";

			reg = <0x900 0x100>;

		};

		pm6125_tz: qcom,temp-alarm@2400 {

			compatible = "qcom,spmi-temp-alarm";

			reg = <0x2400 0x100>;

			interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>;

			#thermal-sensor-cells = <0>;

			qcom,temperature-threshold-set = <1>;

		};

		pm6125_clkdiv: clock-controller@5b00 {

			compatible = "qcom,spmi-clkdiv";

			reg = <0x5b00 0x100>;

			#clock-cells = <1>;

			qcom,num-clkdivs = <1>;

			clock-output-names = "pm6125_div_clk1";

			clocks = <&clock_rpmcc RPM_SMD_XO_CLK_SRC>;

			clock-names = "xo";

			assigned-clocks = <&pm6125_clkdiv 1>;

			assigned-clock-rates = <19200000>;

		};

		pm6125_gpios: pinctrl@c000 {

			compatible = "qcom,spmi-gpio";

			reg = <0xc000 0xa00>;

			interrupts = <0x0 0xc0 0 IRQ_TYPE_NONE>,

					<0x0 0xc1 0 IRQ_TYPE_NONE>,

					<0x0 0xc2 0 IRQ_TYPE_NONE>,

					<0x0 0xc3 0 IRQ_TYPE_NONE>,

					<0x0 0xc4 0 IRQ_TYPE_NONE>,

					<0x0 0xc5 0 IRQ_TYPE_NONE>,

					<0x0 0xc6 0 IRQ_TYPE_NONE>,

					<0x0 0xc7 0 IRQ_TYPE_NONE>,

					<0x0 0xc8 0 IRQ_TYPE_NONE>;

			interrupt-names = "pm6125_gpio1", "pm6125_gpio2",

					"pm6125_gpio3", "pm6125_gpio4",

					"pm6125_gpio5", "pm6125_gpio6",

					"pm6125_gpio7", "pm6125_gpio8",

					"pm6125_gpio9";

			gpio-controller;

			#gpio-cells = <2>;

		};

	};

	qcom,pm6125@1 {

		compatible ="qcom,spmi-pmic";

		reg = <0x1 SPMI_USID>;

		#address-cells = <1>;

		#size-cells = <1>;

	};

};

	};

};

#include "pmi632.dtsi"

#include "pm6125.dtsi"

#include "trinket-pinctrl.dtsi"

#include "trinket-ion.dtsi"

#include "pm6125-rpm-regulator.dtsi"