ARM: dts: Add DTS file for D-Link DIR-685

	exynos5440-ssdk5440.dtb \

	exynos5440-ssdk5440.dtb \

	exynos5800-peach-pi.dtb

	exynos5800-peach-pi.dtb

dtb-$(CONFIG_ARCH_GEMINI) += \

dtb-$(CONFIG_ARCH_GEMINI) += \

	gemini-dlink-dir-685.dtb \

	gemini-nas4220b.dtb \

	gemini-nas4220b.dtb \

	gemini-rut1xx.dtb \

	gemini-rut1xx.dtb \

	gemini-sq201.dtb \

	gemini-sq201.dtb \

/*

 * Device Tree file for D-Link DIR-685 Xtreme N Storage Router

 */

/dts-v1/;

#include "gemini.dtsi"

#include <dt-bindings/input/input.h>

/ {

	model = "D-Link DIR-685 Xtreme N Storage Router";

	compatible = "dlink,dir-685", "cortina,gemini";

	#address-cells = <1>;

	#size-cells = <1>;

	memory {

		/* 128 MB SDRAM in 2 x Hynix HY5DU121622DTP-D43 */

		device_type = "memory";

		reg = <0x00000000 0x8000000>;

	};

	chosen {

		stdout-path = "uart0:115200n8";

	};

	gpio_keys {

		compatible = "gpio-keys";

		#address-cells = <1>;

		#size-cells = <0>;

		button-esc {

			debounce_interval = <50>;

			wakeup-source;

			linux,code = <KEY_ESC>;

			label = "reset";

			gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;

		};

		button-eject {

			debounce_interval = <50>;

			wakeup-source;

			linux,code = <KEY_EJECTCD>;

			label = "unmount";

			gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;

		};

	};

	leds {

		compatible = "gpio-leds";

		led-wps {

			label = "dir685:blue:WPS";

			gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;

			default-state = "on";

			linux,default-trigger = "heartbeat";

		};

		/*

		 * These two LEDs are on the side of the device.

		 * For electrical reasons, both LEDs cannot be active

		 * at the same time so only blue or orange can on at

		 * one time. Enabling both makes the LED go dark.

		 * The LEDs both sit inside the unmount button and the

		 * label on the case says "unmount".

		 */

		led-blue-hd {

			label = "dir685:blue:HD";

			gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>;

			default-state = "off";

		};

		led-orange-hd {

			label = "dir685:orange:HD";

			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;

			default-state = "off";

		};

	};

	/*

	 * This is a Sunon Maglev GM0502PFV2-8 cooling fan @10000 RPM.

	 * Since the platform has no temperature sensor, this is controlled

	 * from userspace by using the hard disks S.M.A.R.T. temperature

	 * sensor. It is turned on when the temperature exceeds 46 degrees

	 * and turned off when the temperatures goes below 41 degrees

	 * (celsius).

	 */

	gpio-fan {

		compatible = "gpio-fan";

		gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;

		gpio-fan,speed-map = <0 0>, <10000 1>;

		#cooling-cells = <2>;

	};

	/*

	 * The touchpad input is connected to a GPIO bit-banged

	 * I2C bus.

	 */

	gpio-i2c {

		compatible = "i2c-gpio";

		gpios = <&gpio0 5 0>, /* SDA */

			<&gpio0 6 0>; /* SCL */

		#address-cells = <1>;

		#size-cells = <0>;

		touchkeys@26 {

			compatible = "dlink,dir685-touchkeys";

			reg = <0x26>;

			interrupt-parent = <&gpio0>;

			interrupts = <17 IRQ_TYPE_EDGE_FALLING>;

		};

	};

	soc {

		flash@30000000 {

			status = "okay";

			/* 32MB of flash */

			reg = <0x30000000 0x02000000>;

			/*

			 * This "RedBoot" is the Storlink derivative.

			 */

			partition@0 {

				label = "RedBoot";

				reg = <0x00000000 0x00040000>;

				read-only;

			};

			/*

			 * Between the boot loader and the rootfs is the kernel

			 * in a custom Storlink format flashed from the boot

			 * menu. The rootfs is in squashfs format.

			 */

			partition@1800c0 {

				label = "rootfs";

				reg = <0x001800c0 0x01dbff40>;

				read-only;

			};

			partition@1f40000 {

				label = "upgrade";

				reg = <0x01f40000 0x00040000>;

				read-only;

			};

			partition@1f80000 {

				label = "rgdb";

				reg = <0x01f80000 0x00040000>;

				read-only;

			};

			/*

			 * This partition contains MAC addresses for WAN,

			 * WLAN and LAN, and the country code (for wireless

			 * I guess).

			 */

			partition@1fc0000 {

				label = "nvram";

				reg = <0x01fc0000 0x00020000>;

				read-only;

			};

			partition@1fe0000 {

				label = "LangPack";

				reg = <0x01fe0000 0x00020000>;

				read-only;

			};

		};

		sata: sata@46000000 {

			cortina,gemini-ata-muxmode = <0>;

			cortina,gemini-enable-sata-bridge;

			status = "okay";

		};

		pci@50000000 {

			status = "okay";

			interrupt-map-mask = <0xf800 0 0 7>;

			interrupt-map =

				<0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */

				<0x4800 0 0 2 &pci_intc 1>,

				<0x4800 0 0 3 &pci_intc 2>,

				<0x4800 0 0 4 &pci_intc 3>,

				<0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */

				<0x5000 0 0 2 &pci_intc 2>,

				<0x5000 0 0 3 &pci_intc 3>,

				<0x5000 0 0 4 &pci_intc 0>,

				<0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */

				<0x5800 0 0 2 &pci_intc 3>,

				<0x5800 0 0 3 &pci_intc 0>,

				<0x5800 0 0 4 &pci_intc 1>,

				<0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */

				<0x6000 0 0 2 &pci_intc 0>,

				<0x6000 0 0 3 &pci_intc 1>,

				<0x6000 0 0 4 &pci_intc 2>;

		};

		ata@63000000 {

			status = "okay";

		};

	};

};