Donate to e Foundation | Murena handsets with /e/OS | Own a part of Murena! Learn more

Commit c7b44586 authored by Guru Das Srinagesh's avatar Guru Das Srinagesh
Browse files

dt-bindings: qcom: qpnp-smb5: Add snapshot 



Add snapshot of dt-bindings for the QPNP-SMB5 driver as of msm-4.14
'commit 7e16ff6cdde5 ("defconfig: qcs405: enable WLAN configs for 32-bit
QCS405")'.

Change-Id: I053d225207e4db95e14cd5ee9b0ef3e012917899
Signed-off-by: default avatarGuru Das Srinagesh <gurus@codeaurora.org>
parent 1b073790

Documentation/devicetree/bindings/power/supply/qcom/qpnp-smb5.txt

0 → 100644
+423 −0
Original line number Diff line number Diff line 
Qualcomm Technologies, Inc. SMB5 Charger Specific Bindings



SMB5 Charger is an efficient programmable battery charger capable of charging a

high-capacity lithium-ion battery over micro-USB or USB Type-C ultrafast with

Quick Charge 2.0, Quick Charge 3.0, and USB Power Delivery support. Wireless

charging features full A4WP Rezence 1.2, WPC 1.2, and PMA support.



=======================

Required Node Structure

=======================



SMB5 Charger must be described in two levels of devices nodes.



===============================

First Level Node - SMB5 Charger

===============================



Charger specific properties:

- compatible

  Usage:      required

  Value type: <string>

  Definition: "qcom,qpnp-smb5".



- qcom,pmic-revid

  Usage:      required

  Value type: phandle

  Definition: Should specify the phandle of PMI's revid module. This is used to

		identify the PMI subtype.



- qcom,sec-charger-config

  Usage:      optional

  Value type: <u32>

  Definition: Specify how the secondary chargers are configured.

		0 - No secondary charger.

		1 - Charge Pump SMB1390.

		2 - SMB1355 parallel charger.

		3 - Both Charge Pump and SMB1355.

		If the value is not present, 0 is used as default.



- io-channels

- io-channel-names

  Usage:      optional

  Value type: <phandle>

  Definition: For details about IIO bindings see:

		Documentation/devicetree/bindings/iio/iio-bindings.txt



- qcom,batteryless-platform

  Usage:      optional

  Value type: <empty>

  Definition: Boolean flag which indicates that the platform does not have a

		battery, and therefore charging should be disabled. In

		addition battery properties will be faked such that the device

		assumes normal operation.



- qcom,charger-temp-max

  Usage:      optional

  Value type: <u32>

  Definition: Specifies the charger temp REG_H_THRESHOLD for PM8150B in deciDegC.

		If the value is not present, use the setting read from the device.



- qcom,smb-temp-max

  Usage:      optional

  Value type: <u32>

  Definition: Specifies the charger temp REG_H_THRESHOLD for SMB1355 in deciDegC.

		If the value is not present, use the setting read from the device.



- qcom,fcc-max-ua

  Usage:      optional

  Value type: <u32>

  Definition: Specifies the maximum fast charge current in micro-amps.

		If the value is not present, 1Amp is used as default.



- qcom,fv-max-uv

  Usage:      optional

  Value type: <u32>

  Definition: Specifies the maximum float voltage in micro-volts.

		If the value is not present, 4.35V is used as default.



- qcom,usb-icl-ua

  Usage:      optional

  Value type: <u32>

  Definition: Specifies the USB input current limit in micro-amps.

		 If the value is not present, 1.5Amps is used as default.



- qcom,usb-ocl-ua

  Usage:      optional

  Value type: <u32>

  Definition: Specifies the OTG output current limit in micro-amps.

		If the value is not present, 1.5Amps is used as default.



- qcom,dc-icl-ua

  Usage:      optional

  Value type: <u32>

  Definition: Specifies the DC input current limit in micro-amps.



- qcom,boost-threshold-ua

  Usage:      optional

  Value type: <u32>

  Definition: Specifies the boost current threshold in micro-amps.

		If the value is not present, 100mA is used as default.



- qcom,thermal-mitigation

  Usage:      optional

  Value type: Array of <u32>

  Definition: Array of fast charge current limit values for

		different system thermal mitigation levels.

		This should be a flat array that denotes the

		maximum charge current in mA for each thermal

		level.



- qcom,float-option

  Usage:      optional

  Value type: <u32>

  Definition: Configures how the charger behaves when a float charger is

	      detected by APSD.

	        1 - Treat as a DCP.

	        2 - Treat as a SDP.

	        3 - Disable charging.

	        4 - Suspend USB input.



- qcom,hvdcp-disable

  Usage:      optional

  Value type: <empty>

  Definition: Specifies if hvdcp charging is to be enabled or not.

		If this property is not specified hvdcp will be enabled.

		If this property is specified, hvdcp 2.0 detection will still

		happen but the adapter won't be asked to switch to a higher

		voltage point.



- qcom,chg-inhibit-threshold-mv

  Usage:      optional

  Value type: <u32>

  Definition: Charge inhibit threshold in milli-volts. Charging will be

		inhibited when the battery voltage is within this threshold

		from Vfloat at charger insertion. If this is not specified

		then charge inhibit will be disabled by default.

		Allowed values are: 50, 100, 200, 300.



- qcom,chg-term-src

  Usage:      optional

  Value type: <u32>

  Definition: Specify either the ADC or analog comparators to be used in order

		to set threshold values for charge termination current.

		0 - Unspecified

		1 - Select ADC comparator

		2 - Select ANALOG comparator



- qcom,chg-term-current-ma

  Usage:      optional

  Value type: <u32>

  Definition: When ADC comparator is selected as qcom,chg-term-src, this

		parameter should be set to the desired upper threshold.



- qcom,chg-term-base-current-ma

  Usage:      optional

  Value type: <u32>

  Definition: When ADC comparator is selected as qcom,chg-term-src, this

		parameter should be set to the desired lower threshold.



- qcom,auto-recharge-soc

  Usage:      optional

  Value type: <u32>

  Definition: Specifies the SOC threshold at which the charger will

		restart charging after termination. The value specified

		ranges from 0 - 100. The feature is enabled if this

		property is specified with a valid SOC value.



- qcom,auto-recharge-vbat-mv

  Usage:      optional

  Value type: <u32>

  Definition: Specifies the battery voltage threshold at which the charger

		will restart charging after termination. The value specified

		is in milli-volts.



- qcom,suspend-input-on-debug-batt

  Usage:      optional

  Value type: <empty>

  Definition: Boolean flag which when present enables input suspend for

		debug battery.



- qcom,min-freq-khz

  Usage:      optional

  Value type: <u32>

  Definition: Specifies the minimum charger buck/boost switching frequency

		in KHz. It overrides the min frequency defined for the charger.



- qcom,max-freq-khz

  Usage:      optional

  Value type: <u32>

  Definition: Specifies the maximum charger buck/boost switching frequency in

		 KHz. It overrides the max frequency defined for the charger.



- qcom,otg-deglitch-time-ms

  Usage:      optional

  Value type: <u32>

  Definition: Specifies the deglitch interval for OTG detection.

		If the value is not present, 50 msec is used as default.



- qcom,step-charging-enable

  Usage:      optional

  Value type: bool

  Definition: Boolean flag which when present enables step-charging.



- qcom,wd-bark-time-secs

  Usage:      optional

  Value type: <u32>

  Definition: WD bark-timeout in seconds. The possible values are

		16, 32, 64, 128. If not defined it defaults to 64.



- qcom,sw-jeita-enable

  Usage:      optional

  Value type: bool

  Definition: Boolean flag which when present enables sw compensation for

		jeita.



- qcom,battery-data

  Usage:      optional

  Value type: <phandle>

  Definition: Specifies the phandle of the node which contains the battery

		profiles supported on the device.



- qcom,flash-derating-soc

  Usage:      optional

  Value type: <u32>

  Definition: SOC threshold in percentage below which hardware will start

		derating flash. This is only applicable to certain PMICs like

		PMI632 which has SCHGM_FLASH peripheral.



- qcom,flash-disable-soc

  Usage:      optional

  Value type: <u32>

  Definition: SOC threshold in percentage below which hardware will disable

		flash. This is only applicable to certain PMICs like PMI632

		which has SCHGM_FLASH peripheral.



- qcom,headroom-mode

  Usage:      optional

  Value type: <u32>

  Definition: Specifies flash hardware headroom management policy. The

		possible values are:

		<0>: Fixed mode, constant 5V at flash input.

		<1>: Adaptive mode allows charger output voltage to be

		dynamically controlled by the flash module based on the

		required flash headroom.

		This is only applicable to certain PMICs like PMI632 which

		has SCHGM_FLASH peripheral.



- qcom,fcc-stepping-enable

  Usage:      optional

  Value type: bool

  Definition: Boolean flag which when present enables stepwise change in FCC.

		The default stepping rate is 100mA/sec.



=============================================

Second Level Nodes - SMB5 Charger Peripherals

=============================================



Peripheral specific properties:

- reg

  Usage:      required

  Value type: <prop-encoded-array>

  Definition: Address and size of the peripheral's register block.



- interrupts

  Usage:      required

  Value type: <prop-encoded-array>

  Definition: Peripheral interrupt specifier.



- interrupt-names

  Usage:      required

  Value type: <stringlist>

  Definition: Interrupt names.  This list must match up 1-to-1 with the

	      interrupts specified in the 'interrupts' property.



=======

Example

=======



pm8150b_charger: qcom,qpnp-smb5 {

	compatible = "qcom,qpnp-smb5";

	#address-cells = <1>;

	#size-cells = <1>;



	qcom,pmic-revid = <&pm8150b_revid>;



	dpdm-supply = <&qusb_phy0>;



	qcom,sec-charger-config = <1>;



	io-channels = <&pm8150b_vadc ADC_USB_IN_V_16>,

	              <&pm8150b_vadc ADC_USB_IN_I>,

	              <&pm8150b_vadc ADC_CHG_TEMP>;

	io-channel-names = "usb_in_voltage",

	                   "usb_in_current",

	                   "chg_temp";



	qcom,chgr@1000 {

		reg = <0x1000 0x100>;

		interrupts =	<0x2 0x10 0x0 IRQ_TYPE_NONE>,

				<0x2 0x10 0x1 IRQ_TYPE_NONE>,

				<0x2 0x10 0x2 IRQ_TYPE_NONE>,

				<0x2 0x10 0x3 IRQ_TYPE_NONE>,

				<0x2 0x10 0x4 IRQ_TYPE_NONE>;



		interrupt-names =	"chg-error",

					"chg-state-change",

					"step-chg-state-change",

					"step-chg-soc-update-fail",

					"step-chg-soc-update-request";

	};



	qcom,otg@1100 {

		reg = <0x1100 0x100>;

		interrupts =	<0x2 0x11 0x0 IRQ_TYPE_NONE>,

				<0x2 0x11 0x1 IRQ_TYPE_NONE>,

				<0x2 0x11 0x2 IRQ_TYPE_NONE>,

				<0x2 0x11 0x3 IRQ_TYPE_NONE>;



		interrupt-names =	"otg-fail",

					"otg-overcurrent",

					"otg-oc-dis-sw-sts",

					"testmode-change-detect";

	};



	qcom,bat-if@1200 {

		reg = <0x1200 0x100>;

		interrupts =	<0x2 0x12 0x0 IRQ_TYPE_NONE>,

				<0x2 0x12 0x1 IRQ_TYPE_NONE>,

				<0x2 0x12 0x2 IRQ_TYPE_NONE>,

				<0x2 0x12 0x3 IRQ_TYPE_NONE>,

				<0x2 0x12 0x4 IRQ_TYPE_NONE>,

				<0x2 0x12 0x5 IRQ_TYPE_NONE>;



		interrupt-names =	"bat-temp",

					"bat-ocp",

					"bat-ov",

					"bat-low",

					"bat-therm-or-id-missing",

					"bat-terminal-missing";

	};



	qcom,usb-chgpth@1300 {

		reg = <0x1300 0x100>;

		interrupts =	<0x2 0x13 0x0 IRQ_TYPE_NONE>,

				<0x2 0x13 0x1 IRQ_TYPE_NONE>,

				<0x2 0x13 0x2 IRQ_TYPE_NONE>,

				<0x2 0x13 0x3 IRQ_TYPE_NONE>,

				<0x2 0x13 0x4 IRQ_TYPE_NONE>,

				<0x2 0x13 0x5 IRQ_TYPE_NONE>,

				<0x2 0x13 0x6 IRQ_TYPE_NONE>,

				<0x2 0x13 0x7 IRQ_TYPE_NONE>;



		interrupt-names =	"usbin-collapse",

					"usbin-lt-3p6v",

					"usbin-uv",

					"usbin-ov",

					"usbin-plugin",

					"usbin-src-change",

					"usbin-icl-change",

					"type-c-change";

	};



	qcom,dc-chgpth@1400 {

		reg = <0x1400 0x100>;

		interrupts =	<0x2 0x14 0x0 IRQ_TYPE_NONE>,

				<0x2 0x14 0x1 IRQ_TYPE_NONE>,

				<0x2 0x14 0x2 IRQ_TYPE_NONE>,

				<0x2 0x14 0x3 IRQ_TYPE_NONE>,

				<0x2 0x14 0x4 IRQ_TYPE_NONE>,

				<0x2 0x14 0x5 IRQ_TYPE_NONE>,

				<0x2 0x14 0x6 IRQ_TYPE_NONE>;



		interrupt-names =	"dcin-collapse",

					"dcin-lt-3p6v",

					"dcin-uv",

					"dcin-ov",

					"dcin-plugin",

					"div2-en-dg",

					"dcin-icl-change";

	};



	qcom,chgr-misc@1600 {

		reg = <0x1600 0x100>;

		interrupts =	<0x2 0x16 0x0 IRQ_TYPE_NONE>,

				<0x2 0x16 0x1 IRQ_TYPE_NONE>,

				<0x2 0x16 0x2 IRQ_TYPE_NONE>,

				<0x2 0x16 0x3 IRQ_TYPE_NONE>,

				<0x2 0x16 0x4 IRQ_TYPE_NONE>,

				<0x2 0x16 0x5 IRQ_TYPE_NONE>,

				<0x2 0x16 0x6 IRQ_TYPE_NONE>,

				<0x2 0x16 0x7 IRQ_TYPE_NONE>;



		interrupt-names =	"wdog-snarl",

					"wdog-bark",

					"aicl-fail",

					"aicl-done",

					"high-duty-cycle",

					"input-current-limiting",

					"temperature-change",

					"switcher-power-ok";

	};



	qcom,schgm-flash@a600 {

		reg = <0xa600 0x100>;

		interrupts =	<0x2 0xa6 0x0 IRQ_TYPE_NONE>,

				<0x2 0xa6 0x1 IRQ_TYPE_NONE>,

				<0x2 0xa6 0x2 IRQ_TYPE_NONE>,

				<0x2 0xa6 0x3 IRQ_TYPE_NONE>,

				<0x2 0xa6 0x4 IRQ_TYPE_NONE>,

				<0x2 0xa6 0x5 IRQ_TYPE_NONE>,

				<0x2 0xa6 0x6 IRQ_TYPE_NONE>,

				<0x2 0xa6 0x7 IRQ_TYPE_NONE>;



		interrupt-names =	"flash-en",

					"torch-req",

					"flash-state-change",

					"vout-up",

					"vout-down",

					"ilim1-s1",

					"ilim2-s2",

					"vreg-ok";

	};

};