dt-bindings: regulator: Add DT bindings for qpnp-labibb regulator (b78e7a09) · Commits · e / devices / android_kernel_oneplus_sm7250

Documentation/devicetree/bindings/regulator/qpnp-labibb-regulator.txt

0 → 100644

+422 −0

Original line number	Diff line number	Diff line
		QTI's LAB (LCD/AMOLED BOOST)/IBB (Inverting Buck-Boost) Regulator

		LAB can be used as a standalone positive boost power supply for general purpose
		applications. IBB can be used as a standalone negative power supply for general
		applications. Also, LAB and IBB can be used together to provide power supply for
		display panels, LCD or AMOLED.

		Main node required properties:

		- compatible: Must be "qcom,qpnp-labibb-regulator"
		- qcom,qpnp-labibb-mode: A string used to specify the working mode of LAB/IBB
		regulators when bootloader does not turned on the
		display panel. Could be "lcd" or "amoled".
		"lcd" means using LAB and IBB regulators are
		configured for LCD mode.
		"amoled" means using LAB and IBB regulators are
		configured for AMOLED mode.
		- qcom,pmic-revid: Specifies the phandle of the PMIC revid module.
		Used to identify the PMIC subtype.

		Main node optional properties:

		- qcom,qpnp-labibb-touch-to-wake-en: A boolean property which upon set will
		enable support for touch-to-wake mode
		by configuring the required settings
		in LAB and IBB modules. Make sure the
		hardware has needed support before
		enabling this property.
		- qcom,swire-control: A boolean property which indicates if the LAB/IBB is
		controlled by the SWIRE interface. Enable only
		if qcom,qpnp-labibb-mode = "amoled".
		- qcom,labibb-ttw-force-lab-on: A boolean property which forces LAB to be
		always on during TTW mode.
		- qcom,skip-2nd-swire-cmd: A boolean property which indicates if
		the second SWIRE command needs to be skipped.
		- qcom,swire-2nd-cmd-delay: An integer value which specifes the
		delay in millisecs between the first and second
		SWIRE command. If not specified this value
		defaults to 20ms. This delay is applied only
		if 'qcom,skip-2nd-swire-cmd' is defined.
		- qcom,swire-ibb-ps-enable-delay: An integer value which specifes the delay
		in millisecs to enable IBB pulse-skipping
		after the skip-2nd-swire-cmd workaround is applied.
		If not specified this value default to 200ms.
		This property is applicable only if
		'qcom,skip-2nd-swire-cmd' is specified.
		- qcom,labibb-standalone: A boolean property which forces LAB and
		IBB to operate in standalone mode. If
		this is not specified, then LAB and IBB
		are controlled together in dual mode.
		- parent-supply: Parent supply that is needed for LAB
		and IBB regulators. This will be mostly
		needed when LAB and IBB are operating
		in standalone mode to vote for MBG.

		Following properties are available only for PM660A:

		- qcom,pbs-control: A boolean property which indicates if
		the LAB/IBB is controlled by the PBS
		sequencer. If this mode is enabled the
		PBS sequencer does the SWIRE remapping
		and program the voltages based on the
		SWIRE count.

		LAB subnode required properties:

		- reg: Specifies the SPMI address and size for this peripheral.
		- reg-names: Register names. Must be "lab".
		- regulator-name: A string used to describe the regulator.
		- regulator-min-microvolt: Minimum voltage in microvolts supported by this regulator.
		- regulator-max-microvolt: Maximum voltage in microvolts supported by this regulator.

		- qcom,qpnp-lab-min-voltage: The minimum voltage in microvolts LAB regulator can support.
		- qcom,qpnp-lab-step-size: The step size in microvolts of LAB regulator.
		- qcom,qpnp-lab-slew-rate: The time in us taken by the regulator to change
		voltage value in one step.

		- qcom,qpnp-lab-init-voltage: The default initial voltage when the bootloader
		does not turn on LAB regulator.
		- qcom,qpnp-lab-init-amoled-voltage: The default output voltage when LAB regulator
		is configured in amoled mode.
		- qcom,qpnp-lab-init-lcd-voltage: The default output voltage when LAB regulator
		is configured in lcd mode.
		- qcom,qpnp-lab-ps-threshold: The threshold in mA of Pulse Skip Mode for
		LAB regulator. Supported values for
		PMI8994/6 are 20, 30, 40 and 50.
		Supported values for PMI8998/PM660A are
		50, 60, 70 and 80.
		- interrupts: Specify the interrupts as per the interrupt
		encoding.
		Currently "lab-vreg-ok" is required and "lab-sc_err"
		is optional for LCD mode in pmi8998.
		For AMOLED mode, "lab-vreg-ok" is required
		only when SWIRE control is enabled and skipping
		2nd SWIRE pulse is required in pmi8952/8996.
		- interrupt-names: Interrupt names to match up 1-to-1 with
		the interrupts specified in 'interrupts'
		property.

		LAB subnode optional properties:

		- qcom,qpnp-lab-current-sense: If this property is specified, the LAB current
		sense gain will be programmed for LAB regulator.
		Otherwise, LAB current sense gain will be
		default to "1x". A string is used to specify the
		LAB current sense gain. Could be "0.5x" or "1x"
		or "1.5x" or "2x". For e.g. "0.5x" means current
		sense gain is 0.5.
		- qcom,qpnp-lab-ps-enable: A boolean proerty which upon set will enable
		pulse skip mode for LAB regulator. Otherwise,
		it is disabled.
		- qcom,qpnp-lab-full-pull-down: A boolean property which upon set will enable
		the pull down strength of LAB regulator to
		full. Otherwise, the pull down strength is
		configured to half.
		- qcom,qpnp-lab-pull-down-enable: A boolean property which upon set will enable
		the pull down for LAB regulator. Otherwise,
		it is disabled.
		- qcom,qpnp-lab-max-precharge-enable: A boolean property which upon set will
		enable fast precharge. Otherwise, it is
		disabled.
		- qcom,qpnp-lab-ring-suppression-enable: A boolean property which upon set will
		enable ring suppression for LAB
		regulator. Otherwise, it is disabled.
		- qcom,qpnp-lab-limit-max-current-enable: A boolean property which upon set will
		enforce maximum inductor current constraint
		for LAB regulator. Otherwise, there is no
		maximum current constraint.
		- qcom,qpnp-lab-switching-clock-frequency: The PWM switching clock frequency in
		kHz of Lab regulator, Supported values
		are: 3200, 2740, 2400, 2130, 1920,
		1750, 1600, 1480, 1370, 1280, 1200,
		1130, 1070, 1010, 960, 910.
		- qcom,qpnp-lab-limit-maximum-current: The maximum inductor current limit in
		mA of LAB regulator. Supported values
		are 200, 400, 600, 800, 1000, 1200,
		1400 and 1600.
		- qcom,qpnp-lab-pfet-size: PFET size in percentage. Supported values
		are 25, 50, 75 and 100.
		- qcom,qpnp-lab-nfet-size: NFET size in percentage. Supported values
		are 25, 50, 75 and 100.
		- qcom,qpnp-lab-max-precharge-time: Precharge time in uS for LAB regulator.
		Supported values are 200, 300, 400 and 500.
		Suggested values for LCD and AMOLED mode
		are 500 and 300uS respectively.
		- qcom,qpnp-lab-use-default-voltage: A boolean property which upon set will
		use the value specified in
		qcom,qpnp-lab-init-voltage property.
		This will be used only if the bootloader
		doesn't configure the output voltage
		already. If it it not specified, then
		output voltage can be configured to
		any value in the allowed limit.
		- qcom,notify-lab-vreg-ok-sts: A boolean property which upon set will
		poll and notify the lab_vreg_ok status.
		- qcom,qpnp-lab-sc-wait-time-ms: This property is used to specify the time
		(in ms) to poll for the short circuit
		detection. If not specified the default time
		is 5 sec.

		Following properties are available only for PM660A:

		- qcom,qpnp-lab-soft-start: The soft start time in us of LAB regulator.
		Supported value are 200, 400, 600 and 800.
		- qcom,qpnp-lab-ldo-pulldown-enable: This property is used to enable/disable
		the LDO pull down.
		1 - enable pulldown
		0 - disable pulldown
		- qcom,qpnp-lab-enable-sw-high-psrr: A boolean property to enable the
		software high psrr
		(Power Suppy Rejection Rate) mode.
		- qcom,qpnp-lab-high-psrr-src-select: This property is used to select the LAB
		HW high psrr source.
		The supported values are:
		0 = Either vph_high or high_psrr enable
		1 = vph_high only
		2 = high_psrr enable only
		3 = Either vph_high or high_psrr enable
		This property is not valid if the
		qcom,qpnp-lab-enable-sw-high-psrr property
		is specified.
		- qcom,qpnp-lab-vref-high-psrr-select: This property is required if the
		qcom,qpnp-lab-high-psrr-src-select is
		specified. The supported values (in mV)
		are 350, 400, 450 and 500. Once the
		rejection rate crosses the selected
		high-psrr voltage the LDO is enabled
		based on the value specified under
		qcom,qpnp-lab-high-psrr-src-select
		property.
		This property is not valid if the
		qcom,qpnp-lab-enable-sw-high-psrr property
		is specified.

		IBB subnode required properties:

		- reg: Specifies the SPMI address and size for this peripheral.
		- reg-names: Register names. Must be "ibb".
		- regulator-name: A string used to describe the regulator.
		- regulator-min-microvolt: Minimum voltage in microvolts supported by this regulator.
		- regulator-max-microvolt: Maximum voltage in microvolts supported by this regulator.

		- qcom,qpnp-ibb-min-voltage: The minimum voltage in microvolts IBB regulator can support.
		- qcom,qpnp-ibb-step-size: The step size in microvolts of IBB regulator.
		- qcom,qpnp-ibb-soft-start: The soft start time in us of IBB regulator.

		- qcom,qpnp-ibb-init-voltage: The default initial voltage when the bootloader does
		not turn on IBB regulator.
		- qcom,qpnp-ibb-init-amoled-voltage: The default output voltage when IBB regulator
		is configured in amoled mode.
		- qcom,qpnp-ibb-init-lcd-voltage: The default output voltage when IBB regulator
		is configured in lcd mode.

		IBB subnode optional properties:

		- interrupts: Specify the interrupts as per the interrupt
		encoding.
		Currently "ibb-sc-err" could be used for LCD mode
		in pmi8998 to detect the short circuit fault.
		- interrupt-names: Interrupt names to match up 1-to-1 with
		the interrupts specified in 'interrupts'
		property.

		- qcom,qpnp-ibb-discharge-resistor: The discharge resistor in Kilo Ohms which
		controls the soft start time. Supported values
		are 300, 64, 32 and 16.

		- qcom,qpnp-ibb-slew-rate: The time (in us) taken by the regulator to change
		voltage value in one step. This property is not
		applicable to PM660A.
		The following properties can be used as an
		alternate.
		qcom,qpnp-ibb-slew-rate-config
		qcom,qpnp-ibb-fast-slew-rate
		qcom,qpnp-ibb-slow-slew-rate
		- qcom,qpnp-ibb-ps-enable: A boolean property which upon set will enable
		pulse skip mode for IBB regulator. Otherwise,
		it is disabled.
		- qcom,qpnp-ibb-num-swire-trans: The number of SWIRE transactions
		after which the pulse skipping is
		enabled. This property is required when
		qpnp-ibb-smart-ps-enable property is
		set.
		- qcom,qpnp-ibb-neg-curr-limit: This property must be set when the
		qpnp-ibb-smart-ps-enable is specified.
		The supported values in mA are 1, 2, 3,
		4, 5, 6 and 7. The recommended value is
		- qcom,qpnp-ibb-full-pull-down: A boolean property which upon set will
		enable the pull down strength of IBB
		regulator to full. Otherwise, the pull
		down strength is configured to half.
		- qcom,qpnp-ibb-pull-down-enable: A boolean property which upon set will enable
		the pull down for IBB regulator. Otherwise,
		it is disabled.
		- qcom,qpnp-ibb-lab-pwrup-delay: Power up delay (in us) for IBB regulator when
		it is enabled or turned on. Supported values
		are 1000, 2000, 4000 and 8000.
		- qcom,qpnp-ibb-lab-pwrdn-delay: Power down delay (in us) for IBB regulator
		when it is disabled or turned off. Supported
		values are 1000, 2000, 4000 and 8000.
		- qcom,qpnp-ibb-switching-clock-frequency: The PWM switching clock frequency in
		kHz of IBB regulator. Supported values
		are: 3200, 2740, 2400, 2130, 1920,
		1750, 1600, 1480, 1370, 1280, 1200,
		1130, 1070, 1010, 960, 910.
		- qcom,qpnp-ibb-limit-maximum-current: The maximum inductor current limit in
		mA of IBB regulator. Supported values
		are: 0, 50, 100, 150, 200, 250, 300,
		350, 400, 450, 500, 550, 600, 650, 700,
		750, 800, 850, 900, 950, 1000, 1050,
		1100, 1150, 1200, 1250, 1300, 1350,
		1400, 1450, 1500 and 1550.
		- qcom,qpnp-ibb-debounce-cycle: The debounce cycle of IBB regulator.
		Supported values are 8, 16, 32 and 64.
		- qcom,qpnp-ibb-en-discharge: A boolean property which upon set will
		enable discharge for IBB regulator.
		Otherwise, it is kept disabled.
		- qcom,qpnp-ibb-ring-suppression-enable: A boolean property which upon set will
		enable ring suppression for IBB
		regulator. Otherwise, it is disabled.
		- qcom,qpnp-ibb-limit-max-current-enable: A boolean property which upon set will
		enforce maximum inductor current constraint
		for IBB regulator. Otherwise, there is no
		maximum current constraint.
		- qcom,qpnp-ibb-use-default-voltage: A boolean property which upon set will
		use the value specified in
		qcom,qpnp-ibb-init-voltage property.
		This will be used only if the bootloader
		doesn't configure the output voltage
		already. If it it not specified, then
		output voltage can be configured to
		any value in the allowed limit.
		- qcom,output-voltage-one-pulse: The expected voltage (in mV) of VDISN signal
		on the first SWIRE pulse. This property
		can be specified only if 'qcom,swire-control'
		is defined. The minimum and maximum values
		are 1400mV and 7700mV.

		Following properties are available only for PM660A:

		- qcom,qpnp-ibb-smart-ps-enable: A boolean property which upon set
		enables smart pulse skip mode for IBB
		regulator. Otherwise, it is disabled.
		This property is only applicable to
		PM660A.
		- qcom,qpnp-ibb-enable-pfm-mode: A boolean property which enables the IBB to work
		in pfm mode.
		- qcom,qpnp-ibb-pfm-peak-curr: The PFM peak current limit settings in mA.
		Supported values are 150, 200, 250, 300,
		350, 400, 450 and 500. This property is
		required if the qcom,qpnp-ibb-enable-pfm-mode
		is true.
		- qcom,qpnp-ibb-pfm-hysteresis: The PFM hysteresis voltage threshold in mV.
		Supported values are 0, 25 and 50.
		This property is required if the
		qcom,qpnp-ibb-enable-pfm-mode is specified.
		- qcom,qpnp-ibb-overload-blank: A boolean property which upon set enables
		the IBB overload blanking.
		- qcom,qpnp-ibb-overload-debounce: The expected overload debounce time (in ms)
		values are 1, 2, 4 and 8.
		This property is required only when the
		qcom,qpnp-ibb-overload-blank is set.
		- qcom,qpnp-ibb-vreg-ok-debounce: The expected vreg-ok-debounce time (us)
		values are 4, 8, 16 and 32.
		This property is required only when the
		qcom,qpnp-ibb-overload-blank is set.
		- qcom,qpnp-ibb-slew-rate-config: A boolean property to configure the
		ibb fast/slow slew rate.
		Either qcom,qpnp-ibb-fast-slew-rate or
		qcom,qpnp-ibb-slow-slew-rate has to be
		specified. Otherwise the
		qcom,qpnp-ibb-slow-slew-rate takes precedence
		over the qcom,qpnp-ibb-fast-slew-rate.
		- qcom,qpnp-ibb-fast-slew-rate: This property is required if the qcom,
		qpnp-ibb-slew-rate-config property is
		specified. Supported values (in us) are
		100, 200, 500, 1000, 2000, 10000, 12000
		and 15000.
		- qcom,qpnp-ibb-slow-slew-rate: This property is required if the qcom,
		qpnp-ibb-slew-rate-config property is
		specified. Supported values (in us) are
		100, 200, 500, 1000, 2000, 10000, 12000
		and 15000.

		Example:
		qcom,pmi8994@3 {
		qpnp-labibb-regulator {
		compatible = "qcom,qpnp-labibb-regulator";
		#address-cells = <1>;
		#size-cells = <1>;
		qcom,qpnp-labibb-mode = "lcd";
		qcom,pmic-revid = <&pmi8994_revid>;
		qcom,skip-2nd-swire-cmd;

		lab_regulator: qcom,lab@de00 {
		reg = <0xde00 0x100>;
		reg-names = "lab";

		interrupts = <0x3 0xde 0x0
		IRQ_TYPE_EDGE_RISING>;
		interrupt-names = "lab-vreg-ok";

		regulator-name = "lab_reg";
		regulator-min-microvolt = <4600000>;
		regulator-max-microvolt = <6000000>;

		qcom,qpnp-lab-min-voltage = <4600000>;
		qcom,qpnp-lab-step-size = <100000>;
		qcom,qpnp-lab-slew-rate = <5000>;
		qcom,qpnp-lab-use-default-voltage;
		qcom,qpnp-lab-init-voltage = <5500000>;
		qcom,qpnp-lab-init-amoled-voltage = <4600000>;
		qcom,qpnp-lab-init-lcd-voltage = <5500000>;

		qcom,qpnp-lab-soft-start = <400>;

		qcom,qpnp-lab-full-pull-down;
		qcom,qpnp-lab-pull-down-enable;
		qcom,qpnp-lab-switching-clock-frequency = <1600>;
		qcom,qpnp-lab-limit-maximum-current = <1600>;
		qcom,qpnp-lab-limit-max-current-enable;
		qcom,qpnp-lab-ps-threshold = <40>;
		qcom,qpnp-lab-ps-enable;
		qcom,qpnp-lab-nfet-size = <100>;
		qcom,qpnp-lab-pfet-size = <100>;
		qcom,qpnp-lab-max-precharge-time = <200>;
		};

		ibb_regulator: qcom,ibb@dc00 {
		reg = <0xdc00 0x100>;
		reg-names = "ibb_reg";
		regulator-name = "ibb_reg";

		regulator-min-microvolt = <4600000>;
		regulator-max-microvolt = <6000000>;

		qcom,qpnp-ibb-min-voltage = <1400000>;
		qcom,qpnp-ibb-step-size = <100000>;
		qcom,qpnp-ibb-slew-rate = <2000000>;
		qcom,qpnp-ibb-use-default-voltage;
		qcom,qpnp-ibb-init-voltage = <5500000>;
		qcom,qpnp-ibb-init-amoled-voltage = <4000000>;
		qcom,qpnp-ibb-init-lcd-voltage = <5500000>;

		qcom,qpnp-ibb-soft-start = <400>;

		qcom,qpnp-ibb-discharge-resistor = <300>;
		qcom,qpnp-ibb-lab-pwrup-delay = <8000>;
		qcom,qpnp-ibb-lab-pwrdn-delay = <8000>;
		qcom,qpnp-ibb-en-discharge;

		qcom,qpnp-ibb-full-pull-down;
		qcom,qpnp-ibb-pull-down-enable;
		qcom,qpnp-ibb-switching-clock-frequency = <1480>;
		qcom,qpnp-ibb-limit-maximum-current = <1550>;
		qcom,qpnp-ibb-debounce-cycle = <16>;
		qcom,qpnp-ibb-limit-max-current-enable;
		qcom,qpnp-ibb-ps-enable;
		};

		};
		};