Merge tag 'qcom-drivers-for-4.19' of... (2de4471a) · Commits · e / devices / android_kernel_oneplus_sm7250

Documentation/devicetree/bindings/arm/msm/qcom,llcc.txt

0 → 100644

+26 −0

Original line number	Original line	Diff line number	Diff line
			== Introduction==

			LLCC (Last Level Cache Controller) provides last level of cache memory in SOC,
			that can be shared by multiple clients. Clients here are different cores in the
			SOC, the idea is to minimize the local caches at the clients and migrate to
			common pool of memory. Cache memory is divided into partitions called slices
			which are assigned to clients. Clients can query the slice details, activate
			and deactivate them.

			Properties:
			- compatible:
			Usage: required
			Value type: <string>
			Definition: must be "qcom,sdm845-llcc"

			- reg:
			Usage: required
			Value Type: <prop-encoded-array>
			Definition: Start address and the the size of the register region.

			Example:

			cache-controller@1100000 {
			compatible = "qcom,sdm845-llcc";
			reg = <0x1100000 0x250000>;
			};

Documentation/devicetree/bindings/soc/qcom/rpmh-rsc.txt

0 → 100644

+137 −0

Original line number	Original line	Diff line number	Diff line
			RPMH RSC:
			------------

			Resource Power Manager Hardened (RPMH) is the mechanism for communicating with
			the hardened resource accelerators on Qualcomm SoCs. Requests to the resources
			can be written to the Trigger Command Set (TCS) registers and using a (addr,
			val) pair and triggered. Messages in the TCS are then sent in sequence over an
			internal bus.

			The hardware block (Direct Resource Voter or DRV) is a part of the h/w entity
			(Resource State Coordinator a.k.a RSC) that can handle multiple sleep and
			active/wake resource requests. Multiple such DRVs can exist in a SoC and can
			be written to from Linux. The structure of each DRV follows the same template
			with a few variations that are captured by the properties here.

			A TCS may be triggered from Linux or triggered by the F/W after all the CPUs
			have powered off to facilitate idle power saving. TCS could be classified as -

			ACTIVE /* Triggered by Linux */
			SLEEP /* Triggered by F/W */
			WAKE /* Triggered by F/W */
			CONTROL /* Triggered by F/W */

			The order in which they are described in the DT, should match the hardware
			configuration.

			Requests can be made for the state of a resource, when the subsystem is active
			or idle. When all subsystems like Modem, GPU, CPU are idle, the resource state
			will be an aggregate of the sleep votes from each of those subsystems. Clients
			may request a sleep value for their shared resources in addition to the active
			mode requests.

			Properties:

			- compatible:
			Usage: required
			Value type: <string>
			Definition: Should be "qcom,rpmh-rsc".

			- reg:
			Usage: required
			Value type: <prop-encoded-array>
			Definition: The first register specifies the base address of the
			DRV(s). The number of DRVs in the dependent on the RSC.
			The tcs-offset specifies the start address of the
			TCS in the DRVs.

			- reg-names:
			Usage: required
			Value type: <string>
			Definition: Maps the register specified in the reg property. Must be
			"drv-0", "drv-1", "drv-2" etc and "tcs-offset". The

			- interrupts:
			Usage: required
			Value type: <prop-encoded-interrupt>
			Definition: The interrupt that trips when a message complete/response
			is received for this DRV from the accelerators.

			- qcom,drv-id:
			Usage: required
			Value type: <u32>
			Definition: The id of the DRV in the RSC block that will be used by
			this controller.

			- qcom,tcs-config:
			Usage: required
			Value type: <prop-encoded-array>
			Definition: The tuple defining the configuration of TCS.
			Must have 2 cells which describe each TCS type.
			<type number_of_tcs>.
			The order of the TCS must match the hardware
			configuration.
			- Cell #1 (TCS Type): TCS types to be specified -
			ACTIVE_TCS
			SLEEP_TCS
			WAKE_TCS
			CONTROL_TCS
			- Cell #2 (Number of TCS): <u32>

			- label:
			Usage: optional
			Value type: <string>
			Definition: Name for the RSC. The name would be used in trace logs.

			Drivers that want to use the RSC to communicate with RPMH must specify their
			bindings as child nodes of the RSC controllers they wish to communicate with.

			Example 1:

			For a TCS whose RSC base address is is 0x179C0000 and is at a DRV id of 2, the
			register offsets for DRV2 start at 0D00, the register calculations are like
			this -
			DRV0: 0x179C0000
			DRV2: 0x179C0000 + 0x10000 = 0x179D0000
			DRV2: 0x179C0000 + 0x10000 * 2 = 0x179E0000
			TCS-OFFSET: 0xD00

			apps_rsc: rsc@179c0000 {
			label = "apps_rsc";
			compatible = "qcom,rpmh-rsc";
			reg = <0x179c0000 0x10000>,
			<0x179d0000 0x10000>,
			<0x179e0000 0x10000>;
			reg-names = "drv-0", "drv-1", "drv-2";
			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
			<GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
			<GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
			qcom,tcs-offset = <0xd00>;
			qcom,drv-id = <2>;
			qcom,tcs-config = <ACTIVE_TCS 2>,
			<SLEEP_TCS 3>,
			<WAKE_TCS 3>,
			<CONTROL_TCS 1>;
			};

			Example 2:

			For a TCS whose RSC base address is 0xAF20000 and is at DRV id of 0, the
			register offsets for DRV0 start at 01C00, the register calculations are like
			this -
			DRV0: 0xAF20000
			TCS-OFFSET: 0x1C00

			disp_rsc: rsc@af20000 {
			label = "disp_rsc";
			compatible = "qcom,rpmh-rsc";
			reg = <0xaf20000 0x10000>;
			reg-names = "drv-0";
			interrupts = <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>;
			qcom,tcs-offset = <0x1c00>;
			qcom,drv-id = <0>;
			qcom,tcs-config = <ACTIVE_TCS 0>,
			<SLEEP_TCS 1>,
			<WAKE_TCS 1>,
			<CONTROL_TCS 0>;
			};

drivers/soc/qcom/Kconfig

+27 −0

Original line number	Original line	Diff line number	Diff line
	@@ -39,6 +39,23 @@ config QCOM_GSBI
	functions for connecting the underlying serial UART, SPI, and I2C		functions for connecting the underlying serial UART, SPI, and I2C
	devices to the output pins.		devices to the output pins.

			config QCOM_LLCC
			tristate "Qualcomm Technologies, Inc. LLCC driver"
			depends on ARCH_QCOM
			help
			Qualcomm Technologies, Inc. platform specific
			Last Level Cache Controller(LLCC) driver. This provides interfaces
			to clients that use the LLCC. Say yes here to enable LLCC slice
			driver.

			config QCOM_SDM845_LLCC
			tristate "Qualcomm Technologies, Inc. SDM845 LLCC driver"
			depends on QCOM_LLCC
			help
			Say yes here to enable the LLCC driver for SDM845. This provides
			data required to configure LLCC so that clients can start using the
			LLCC slices.

	config QCOM_MDT_LOADER		config QCOM_MDT_LOADER
	tristate		tristate
	select QCOM_SCM		select QCOM_SCM
	@@ -74,6 +91,16 @@ config QCOM_RMTFS_MEM

	Say y here if you intend to boot the modem remoteproc.		Say y here if you intend to boot the modem remoteproc.

			config QCOM_RPMH
			bool "Qualcomm RPM-Hardened (RPMH) Communication"
			depends on ARCH_QCOM && ARM64 && OF \|\| COMPILE_TEST
			help
			Support for communication with the hardened-RPM blocks in
			Qualcomm Technologies Inc (QTI) SoCs. RPMH communication uses an
			internal bus to transmit state requests for shared resources. A set
			of hardware components aggregate requests for these resources and
			help apply the aggregated state on the resource.

	config QCOM_SMEM		config QCOM_SMEM
	tristate "Qualcomm Shared Memory Manager (SMEM)"		tristate "Qualcomm Shared Memory Manager (SMEM)"
	depends on ARCH_QCOM		depends on ARCH_QCOM

drivers/soc/qcom/Makefile

+6 −0

drivers/soc/qcom/llcc-sdm845.c

0 → 100644

+94 −0

Original line number	Original line	Diff line number	Diff line
			// SPDX-License-Identifier: GPL-2.0
			/*
			* Copyright (c) 2017-2018, The Linux Foundation. All rights reserved.
			*
			*/

			#include <linux/kernel.h>
			#include <linux/module.h>
			#include <linux/of.h>
			#include <linux/of_device.h>
			#include <linux/soc/qcom/llcc-qcom.h>

			/*
			* SCT(System Cache Table) entry contains of the following members:
			* usecase_id: Unique id for the client's use case
			* slice_id: llcc slice id for each client
			* max_cap: The maximum capacity of the cache slice provided in KB
			* priority: Priority of the client used to select victim line for replacement
			* fixed_size: Boolean indicating if the slice has a fixed capacity
			* bonus_ways: Bonus ways are additional ways to be used for any slice,
			* if client ends up using more than reserved cache ways. Bonus
			* ways are allocated only if they are not reserved for some
			* other client.
			* res_ways: Reserved ways for the cache slice, the reserved ways cannot
			* be used by any other client than the one its assigned to.
			* cache_mode: Each slice operates as a cache, this controls the mode of the
			* slice: normal or TCM(Tightly Coupled Memory)
			* probe_target_ways: Determines what ways to probe for access hit. When
			* configured to 1 only bonus and reserved ways are probed.
			* When configured to 0 all ways in llcc are probed.
			* dis_cap_alloc: Disable capacity based allocation for a client
			* retain_on_pc: If this bit is set and client has maintained active vote
			* then the ways assigned to this client are not flushed on power
			* collapse.
			* activate_on_init: Activate the slice immediately after the SCT is programmed
			*/
			#define SCT_ENTRY(uid, sid, mc, p, fs, bway, rway, cmod, ptw, dca, rp, a) \
			{ \
			.usecase_id = uid, \
			.slice_id = sid, \
			.max_cap = mc, \
			.priority = p, \
			.fixed_size = fs, \
			.bonus_ways = bway, \
			.res_ways = rway, \
			.cache_mode = cmod, \
			.probe_target_ways = ptw, \
			.dis_cap_alloc = dca, \
			.retain_on_pc = rp, \
			.activate_on_init = a, \
			}

			static struct llcc_slice_config sdm845_data[] = {
			SCT_ENTRY(LLCC_CPUSS, 1, 2816, 1, 0, 0xffc, 0x2, 0, 0, 1, 1, 1),
			SCT_ENTRY(LLCC_VIDSC0, 2, 512, 2, 1, 0x0, 0x0f0, 0, 0, 1, 1, 0),
			SCT_ENTRY(LLCC_VIDSC1, 3, 512, 2, 1, 0x0, 0x0f0, 0, 0, 1, 1, 0),
			SCT_ENTRY(LLCC_ROTATOR, 4, 563, 2, 1, 0x0, 0x00e, 2, 0, 1, 1, 0),
			SCT_ENTRY(LLCC_VOICE, 5, 2816, 1, 0, 0xffc, 0x2, 0, 0, 1, 1, 0),
			SCT_ENTRY(LLCC_AUDIO, 6, 2816, 1, 0, 0xffc, 0x2, 0, 0, 1, 1, 0),
			SCT_ENTRY(LLCC_MDMHPGRW, 7, 1024, 2, 0, 0xfc, 0xf00, 0, 0, 1, 1, 0),
			SCT_ENTRY(LLCC_MDM, 8, 2816, 1, 0, 0xffc, 0x2, 0, 0, 1, 1, 0),
			SCT_ENTRY(LLCC_CMPT, 10, 2816, 1, 0, 0xffc, 0x2, 0, 0, 1, 1, 0),
			SCT_ENTRY(LLCC_GPUHTW, 11, 512, 1, 1, 0xc, 0x0, 0, 0, 1, 1, 0),
			SCT_ENTRY(LLCC_GPU, 12, 2304, 1, 0, 0xff0, 0x2, 0, 0, 1, 1, 0),
			SCT_ENTRY(LLCC_MMUHWT, 13, 256, 2, 0, 0x0, 0x1, 0, 0, 1, 0, 1),
			SCT_ENTRY(LLCC_CMPTDMA, 15, 2816, 1, 0, 0xffc, 0x2, 0, 0, 1, 1, 0),
			SCT_ENTRY(LLCC_DISP, 16, 2816, 1, 0, 0xffc, 0x2, 0, 0, 1, 1, 0),
			SCT_ENTRY(LLCC_VIDFW, 17, 2816, 1, 0, 0xffc, 0x2, 0, 0, 1, 1, 0),
			SCT_ENTRY(LLCC_MDMHPFX, 20, 1024, 2, 1, 0x0, 0xf00, 0, 0, 1, 1, 0),
			SCT_ENTRY(LLCC_MDMPNG, 21, 1024, 0, 1, 0x1e, 0x0, 0, 0, 1, 1, 0),
			SCT_ENTRY(LLCC_AUDHW, 22, 1024, 1, 1, 0xffc, 0x2, 0, 0, 1, 1, 0),
			};

			static int sdm845_qcom_llcc_probe(struct platform_device *pdev)
			{
			return qcom_llcc_probe(pdev, sdm845_data, ARRAY_SIZE(sdm845_data));
			}

			static const struct of_device_id sdm845_qcom_llcc_of_match[] = {
			{ .compatible = "qcom,sdm845-llcc", },
			{ }
			};

			static struct platform_driver sdm845_qcom_llcc_driver = {
			.driver = {
			.name = "sdm845-llcc",
			.of_match_table = sdm845_qcom_llcc_of_match,
			},
			.probe = sdm845_qcom_llcc_probe,
			};
			module_platform_driver(sdm845_qcom_llcc_driver);

			MODULE_DESCRIPTION("QCOM sdm845 LLCC driver");
			MODULE_LICENSE("GPL v2");

Original line number	Original line	Diff line number	Diff line
	# SPDX-License-Identifier: GPL-2.0		# SPDX-License-Identifier: GPL-2.0
			CFLAGS_rpmh-rsc.o := -I$(src)
	obj-$(CONFIG_QCOM_GENI_SE) += qcom-geni-se.o		obj-$(CONFIG_QCOM_GENI_SE) += qcom-geni-se.o
	obj-$(CONFIG_QCOM_COMMAND_DB) += cmd-db.o		obj-$(CONFIG_QCOM_COMMAND_DB) += cmd-db.o
	obj-$(CONFIG_QCOM_GLINK_SSR) += glink_ssr.o		obj-$(CONFIG_QCOM_GLINK_SSR) += glink_ssr.o
	@@ -8,6 +9,9 @@ obj-$(CONFIG_QCOM_PM) += spm.o
	obj-$(CONFIG_QCOM_QMI_HELPERS) += qmi_helpers.o		obj-$(CONFIG_QCOM_QMI_HELPERS) += qmi_helpers.o
	qmi_helpers-y += qmi_encdec.o qmi_interface.o		qmi_helpers-y += qmi_encdec.o qmi_interface.o
	obj-$(CONFIG_QCOM_RMTFS_MEM) += rmtfs_mem.o		obj-$(CONFIG_QCOM_RMTFS_MEM) += rmtfs_mem.o
			obj-$(CONFIG_QCOM_RPMH) += qcom_rpmh.o
			qcom_rpmh-y += rpmh-rsc.o
			qcom_rpmh-y += rpmh.o
	obj-$(CONFIG_QCOM_SMD_RPM) += smd-rpm.o		obj-$(CONFIG_QCOM_SMD_RPM) += smd-rpm.o
	obj-$(CONFIG_QCOM_SMEM) += smem.o		obj-$(CONFIG_QCOM_SMEM) += smem.o
	obj-$(CONFIG_QCOM_SMEM_STATE) += smem_state.o		obj-$(CONFIG_QCOM_SMEM_STATE) += smem_state.o
	@@ -15,3 +19,5 @@ obj-$(CONFIG_QCOM_SMP2P) += smp2p.o
	obj-$(CONFIG_QCOM_SMSM) += smsm.o		obj-$(CONFIG_QCOM_SMSM) += smsm.o
	obj-$(CONFIG_QCOM_WCNSS_CTRL) += wcnss_ctrl.o		obj-$(CONFIG_QCOM_WCNSS_CTRL) += wcnss_ctrl.o
	obj-$(CONFIG_QCOM_APR) += apr.o		obj-$(CONFIG_QCOM_APR) += apr.o
			obj-$(CONFIG_QCOM_LLCC) += llcc-slice.o
			obj-$(CONFIG_QCOM_SDM845_LLCC) += llcc-sdm845.o