Merge "dt-bindings: msm: Add documentation bindings for QCOM IPA"

Qualcomm technologies inc. Internet Packet Accelerator

Internet Packet Accelerator (IPA) is a programmable protocol

processor HW block. It is designed to support generic HW processing

of UL/DL IP packets for various use cases independent of radio technology.

Required properties:

IPA node:

- compatible : "qcom,ipa"

- reg: Specifies the base physical addresses and the sizes of the IPA

       registers.

- reg-names: "ipa-base" - string to identify the IPA CORE base registers.

	     "bam-base" - string to identify the IPA BAM base registers.

	     "a2-bam-base" - string to identify the A2 BAM base registers.

- interrupts: Specifies the interrupt associated with IPA.

- interrupt-names: "ipa-irq" - string to identify the IPA core interrupt.

                   "bam-irq" - string to identify the IPA BAM interrupt.

                   "a2-bam-irq" - string to identify the A2 BAM interrupt.

- qcom,ipa-hw-ver: Specifies the IPA hardware version.

Optional:

- qcom,use-ipa-pm: Use IPAPM mechanism for power management instead

-	of IPARM

- qcom,wan-rx-ring-size: size of WAN rx ring, default is 192

- qcom,lan-rx-ring-size: size of LAN rx ring, default is 192

- qcom,arm-smmu: SMMU is present and ARM SMMU driver is used

- qcom,msm-smmu: SMMU is present and QSMMU driver is used

- qcom,smmu-fast-map: Boolean context flag to set SMMU to fastpath mode

- ipa_smmu_ap: AP general purpose SMMU device

	compatible "qcom,ipa-smmu-ap-cb"

- ipa_smmu_wlan: WDI SMMU device

	compatible "qcom,ipa-smmu-wlan-cb"

- ipa_smmu_uc: uc SMMU device

	compatible "qcom,ipa-smmu-uc-cb"

- qcom,use-ipa-tethering-bridge: determine if tethering bridge will be used

- qcom,use-ipa-in-mhi-mode: Boolean context flag to indicate whether

				device booting in MHI config or not.

- qcom,ee: which EE is assigned to (non-secure) APPS from IPA-BAM POV. This

is a number

- qcom,ipa-hw-mode: IPA hardware mode - Normal, Virtual memory allocation,

memory allocation over a PCIe bridge

- qcom,msm-bus,name:            String representing the client-name

- qcom,msm-bus,num-cases:       Total number of usecases

- qcom,msm-bus,active-only:     Boolean context flag for requests in active or

                                dual (active & sleep) contex

- qcom,msm-bus,num-paths:       Total number of master-slave pairs

- qcom,msm-bus,vectors-KBps:    Arrays of unsigned integers representing:

                                master-id, slave-id, arbitrated bandwidth

                                in KBps, instantaneous bandwidth in KBps

- qcom,ipa-bam-remote-mode:     Boolean context flag to determine if ipa bam

                                is in remote mode.

- qcom,modem-cfg-emb-pipe-flt:  Boolean context flag to determine if modem

                                configures embedded pipe filtering rules

- qcom,skip-uc-pipe-reset:      Boolean context flag to indicate whether

                                a pipe reset via the IPA uC is required

- qcom,ipa-wdi2:		Boolean context flag to indicate whether

				using wdi-2.0 or not

- qcom,bandwidth-vote-for-ipa:	Boolean context flag to indicate whether

				ipa clock voting is done by bandwidth

				voting via msm-bus-scale driver or not

- qcom,use-64-bit-dma-mask:     Boolean context flag to indicate whether

                                using 64bit dma mask or not

- qcom,use-dma-zone:            Boolean context flag to indicate whether memory

                                allocations controlled by IPA driver that do not

				specify a struct device * should use GFP_DMA to

				workaround IPA HW limitations

- qcom,use-rg10-limitation-mitigation:	Boolean context flag to activate

					the mitigation to register group 10

					AP access limitation

- qcom,do-not-use-ch-gsi-20:	Boolean context flag to activate

				software workaround for IPA limitation

				to not use GSI physical channel 20

- qcom,tethered-flow-control:   Boolean context flag to indicate whether

                                apps based flow control is needed for tethered

                                call.

- qcom,rx-polling-sleep-ms:	Receive Polling Timeout in millisecond,

				default is 1 millisecond.

- qcom,ipa-polling-iteration:	IPA Polling Iteration Count,default is 40.

- qcom,mhi-event-ring-id-limits: Two elements property. Start and End limits

					for MHI event rings ids.

- qcom,ipa-tz-unlock-reg:       Register start addresses and ranges which

                                need to be unlocked by TZ.

- qcom,ipa-uc-monitor-holb:   	Boolean context flag to indicate whether

                                monitoring of holb via IPA uc is required.

-qcom,ipa-fltrt-not-hashable:   Boolean context flag to indicate filter/route rules

				hashing not supported.

- qcom,wlan-ce-db-over-pcie: Boolean context flag to represent WLAN CE DB

				over pcie bus or not.

- qcom,ipa-wdi2_over_gsi: Boolean context flag to indicate WDI2 offload over GSI

				supported or not.

Optional properties:

-qcom,ipa-pipe-mem: Specifies the base physical address and the

                    size of the IPA pipe memory region.

                    Pipe memory is a feature which may be supported by the

                    target (HW platform). The Driver support using pipe

                    memory instead of system memory. In case this property

                    will not appear in the IPA DTS entry, the driver will

                    use system memory.

- clocks: This property shall provide a list of entries each of which

    contains a phandle to clock controller device and a macro that is

    the clock's name in hardware.This should be "clock_rpm" as clock

    controller phandle and "clk_ipa_clk" as macro for "iface_clk"

- clock-names: This property shall contain the clock input names used

    by driver in same order as the clocks property.This should be "iface_clk"

- emulator-bar0-offset: Specifies the offset, within PCIe BAR0, where

    IPA/GSI programmable registers reside.  This property is used only

    with the IPA/GSI emulation system, which is connected to and

    communicated with via PCIe.

IPA SMMU sub nodes

-compatible: "qcom,ipa-smmu-ap-cb" - represents the AP context bank.

-compatible: "qcom,ipa-smmu-wlan-cb" - represents IPA WLAN context bank.

-compatible: "qcom,ipa-smmu-uc-cb" - represents IPA uC context bank (for uC

					offload scenarios).

- qcom,smmu-s1-bypass: Boolean context flag to set SMMU to S1 bypass.

- dma-coherent: Indicate using dma-coherent or not in SMMU block

- iommus : the phandle and stream IDs for the SMMU used by this root

- qcom,iova-mapping: specifies the start address and size of iova space.

- qcom,additional-mapping: specifies any addtional mapping needed for this

				context bank. The format is <iova pa size>

IPA SMP2P sub nodes

-compatible: "qcom,smp2p-map-ipa-1-out" - represents the out smp2p from

					      ipa driver to modem.

-compatible: "qcom,smp2p-map-ipa-1-in" - represents the in smp2p to

					     ipa driver from modem.

Example:

qcom,ipa@fd4c0000 {

	compatible = "qcom,ipa";

	reg = <0xfd4c0000 0x26000>,

	      <0xfd4c4000 0x14818>;

	      <0xfc834000 0x7000>;

	reg-names = "ipa-base", "bam-base"; "a2-bam-base";

	interrupts = <0 252 0>,

	             <0 253 0>;

	             <0 29 1>;

	interrupt-names = "ipa-irq", "bam-irq"; "a2-bam-irq";

	qcom,ipa-hw-ver = <1>;

        qcom,msm-bus,name = "ipa";

        qcom,msm-bus,num-cases = <3>;

        qcom,msm-bus,num-paths = <2>;

        qcom,msm-bus,vectors-KBps =

        <90 512 0 0>, <90 585 0 0>,         /* No vote */

        <90 512 100000 800000>, <90 585 100000 800000>,    /* SVS */

        <90 512 100000 1200000>, <90 585 100000 1200000>;    /* PERF */

        qcom,bus-vector-names = "MIN", "SVS", "PERF";

	/* smp2p information */

	qcom,smp2p_map_ipa_1_out {

		compatible = "qcom,smp2p-map-ipa-1-out";

	};

	qcom,smp2p_map_ipa_1_in {

		compatible = "qcom,smp2p-map-ipa-1-in";

	};

	ipa_smmu_ap: ipa_smmu_ap {

		compatible = "qcom,ipa-smmu-ap-cb";

		iommus = <&apps_smmu 0x720>;

		qcom,iova-mapping = <0x20000000 0x40000000>;

		qcom,additional-mapping =

		/* modem tables in IMEM */

		<0x146bd000 0x146bd000 0x2000>;

	};

	ipa_smmu_wlan: ipa_smmu_wlan {

		compatible = "qcom,ipa-smmu-wlan-cb";

		iommus = <&apps_smmu 0x721>;

		qcom,additional-mapping =

		/* ipa-uc ram */

		<0x1e60000 0x1e60000 0x80000>;

	};

	ipa_smmu_uc: ipa_smmu_uc {

		compatible = "qcom,ipa-smmu-uc-cb";

		iommus = <&apps_smmu 0x722>;

		qcom,iova-mapping = <0x40000000 0x20000000>;

	};

};

* Qualcomm Technologies, Inc. IPA MHI proxy driver module

This module enables modem to modem communication using IPA

and MHI.

Required properties:

- compatible:		Must be "qcom,ipa-mhi-proxy"

- qcom,mhi-chdb-base:	MHI channel doorbell base address in MMIO space

- qcom,mhi-erdb-base:	MHI event doorbell base address in MMIO space

Optional:

- qcom,ctrl-iova: 		Pair of start address and size of the IOVA space

				dedicated for MHI control structures

				(such as transfer rings and event rings).

				If not present, SMMU S1 is considered to be in bypass mode.

- qcom,data-iova: 		Pair of start address and size of the IOVA space

				dedicated for MHI data buffers.

				If not present, SMMU S1 is considered to be in bypass mode.

Example:

	imp: qcom,ipa-mhi-proxy {

		compatible = "qcom,ipa-mhi-proxy";

		qcom,ctrl-iova = <0x00010000 0x0FFF0000>;

		qcom,data-iova = <0x10000000 0x0FFFFFFF>;

		qcom,mhi-chdb-base = <0x40300300>;

		qcom,mhi-erdb-base = <0x40300700>;

	};

* Qualcomm Technologies, Inc. GSI driver module

GSI is a HW accelerator that supports Generic SW Interfaces (GSI) which are

peripheral specific (IPA in this case).

GSI translates SW transfer elements (TRE) into TLV transactions which are

then processed by the peripheral.

This Driver configures and communicates with GSI HW.

Required properties:

- compatible:		Must be "qcom,msm_gsi"

Example:

	qcom,msm-gsi {

		compatible = "qcom,msm_gsi";

	}

* Qualcomm Technologies, Inc. RmNet IPA driver module

This module enables embedded data calls using IPA v3 HW.

Required properties:

- compatible:		Must be "qcom,rmnet-ipa3"

Optional:

- qcom,rmnet-ipa-ssr: determine if modem SSR is supported

- qcom,ipa-platform-type-msm: indicates the platform type is msm or not

- qcom,ipa-advertise-sg-support: determine how to respond to a query

regarding scatter-gather capability

- qcom,ipa-napi-enable: Boolean context flag to indicate whether

                        to enable napi framework or not

- qcom,wan-rx-desc-size: size of WAN rx desc fifo ring, default is 256

Example:

	qcom,rmnet-ipa3 {

		compatible = "qcom,rmnet-ipa3";

		qcom,wan-rx-desc-size = <256>;

	}