ARM: at91: add Atmel's SAMA5D3 Xplained board (b7c2b615) · Commits · e / devices / android_kernel_fairphone_FP5

arch/arm/boot/dts/Makefile

+1 −0

Original line number	Original line	Diff line number	Diff line
	@@ -38,6 +38,7 @@ dtb-$(CONFIG_ARCH_AT91) += at91sam9g35ek.dtb
	dtb-$(CONFIG_ARCH_AT91) += at91sam9x25ek.dtb		dtb-$(CONFIG_ARCH_AT91) += at91sam9x25ek.dtb
	dtb-$(CONFIG_ARCH_AT91) += at91sam9x35ek.dtb		dtb-$(CONFIG_ARCH_AT91) += at91sam9x35ek.dtb
	# sama5d3		# sama5d3
			dtb-$(CONFIG_ARCH_AT91) += at91-sama5d3_xplained.dtb
	dtb-$(CONFIG_ARCH_AT91) += sama5d31ek.dtb		dtb-$(CONFIG_ARCH_AT91) += sama5d31ek.dtb
	dtb-$(CONFIG_ARCH_AT91) += sama5d33ek.dtb		dtb-$(CONFIG_ARCH_AT91) += sama5d33ek.dtb
	dtb-$(CONFIG_ARCH_AT91) += sama5d34ek.dtb		dtb-$(CONFIG_ARCH_AT91) += sama5d34ek.dtb

arch/arm/boot/dts/at91-sama5d3_xplained.dts

0 → 100644

+229 −0

Original line number	Original line	Diff line number	Diff line
			/*
			* at91-sama5d3_xplained.dts - Device Tree file for the SAMA5D3 Xplained board
			*
			* Copyright (C) 2014 Atmel,
			* 2014 Nicolas Ferre <nicolas.ferre@atmel.com>
			*
			* Licensed under GPLv2 or later.
			*/
			/dts-v1/;
			#include "sama5d36.dtsi"

			/ {
			model = "SAMA5D3 Xplained";
			compatible = "atmel,sama5d3-xplained", "atmel,sama5d3", "atmel,sama5";

			chosen {
			bootargs = "console=ttyS0,115200";
			};

			memory {
			reg = <0x20000000 0x10000000>;
			};

			ahb {
			apb {
			mmc0: mmc@f0000000 {
			pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_dat4_7 &pinctrl_mmc0_cd>;
			status = "okay";
			slot@0 {
			reg = <0>;
			bus-width = <8>;
			cd-gpios = <&pioE 0 GPIO_ACTIVE_LOW>;
			};
			};

			spi0: spi@f0004000 {
			cs-gpios = <&pioD 13 0>;
			status = "okay";
			};

			can0: can@f000c000 {
			status = "okay";
			};

			i2c0: i2c@f0014000 {
			status = "okay";
			};

			i2c1: i2c@f0018000 {
			status = "okay";
			};

			macb0: ethernet@f0028000 {
			phy-mode = "rgmii";
			status = "okay";
			};

			usart0: serial@f001c000 {
			status = "okay";
			};

			usart1: serial@f0020000 {
			pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
			status = "okay";
			};

			uart0: serial@f0024000 {
			status = "okay";
			};

			mmc1: mmc@f8000000 {
			pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
			status = "okay";
			slot@0 {
			reg = <0>;
			bus-width = <4>;
			cd-gpios = <&pioE 1 GPIO_ACTIVE_HIGH>;
			};
			};

			spi1: spi@f8008000 {
			cs-gpios = <&pioC 25 0>, <0>, <0>, <&pioD 16 0>;
			status = "okay";
			};

			adc0: adc@f8018000 {
			pinctrl-0 = <
			&pinctrl_adc0_adtrg
			&pinctrl_adc0_ad0
			&pinctrl_adc0_ad1
			&pinctrl_adc0_ad2
			&pinctrl_adc0_ad3
			&pinctrl_adc0_ad4
			&pinctrl_adc0_ad5
			&pinctrl_adc0_ad6
			&pinctrl_adc0_ad7
			&pinctrl_adc0_ad8
			&pinctrl_adc0_ad9
			>;
			status = "okay";
			};

			i2c2: i2c@f801c000 {
			dmas = <0>, <0>; /* Do not use DMA for i2c2 */
			status = "okay";
			};

			macb1: ethernet@f802c000 {
			phy-mode = "rmii";
			status = "okay";
			};

			dbgu: serial@ffffee00 {
			status = "okay";
			};

			pinctrl@fffff200 {
			board {
			pinctrl_mmc0_cd: mmc0_cd {
			atmel,pins =
			<AT91_PIOE 0 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
			};

			pinctrl_mmc1_cd: mmc1_cd {
			atmel,pins =
			<AT91_PIOE 1 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
			};

			pinctrl_usba_vbus: usba_vbus {
			atmel,pins =
			<AT91_PIOE 9 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PE9, conflicts with A9 */
			};
			};
			};

			pmc: pmc@fffffc00 {
			main: mainck {
			clock-frequency = <12000000>;
			};
			};
			};

			nand0: nand@60000000 {
			nand-bus-width = <8>;
			nand-ecc-mode = "hw";
			atmel,has-pmecc;
			atmel,pmecc-cap = <4>;
			atmel,pmecc-sector-size = <512>;
			nand-on-flash-bbt;
			status = "okay";

			at91bootstrap@0 {
			label = "at91bootstrap";
			reg = <0x0 0x40000>;
			};

			bootloader@40000 {
			label = "bootloader";
			reg = <0x40000 0x80000>;
			};

			bootloaderenv@c0000 {
			label = "bootloader env";
			reg = <0xc0000 0xc0000>;
			};

			dtb@180000 {
			label = "device tree";
			reg = <0x180000 0x80000>;
			};

			kernel@200000 {
			label = "kernel";
			reg = <0x200000 0x600000>;
			};

			rootfs@800000 {
			label = "rootfs";
			reg = <0x800000 0x0f800000>;
			};
			};

			usb0: gadget@00500000 {
			atmel,vbus-gpio = <&pioE 9 GPIO_ACTIVE_HIGH>; /* PE9, conflicts with A9 */
			pinctrl-names = "default";
			pinctrl-0 = <&pinctrl_usba_vbus>;
			status = "okay";
			};

			usb1: ohci@00600000 {
			num-ports = <3>;
			atmel,vbus-gpio = <0
			&pioE 3 GPIO_ACTIVE_LOW
			&pioE 4 GPIO_ACTIVE_LOW
			>;
			status = "okay";
			};

			usb2: ehci@00700000 {
			status = "okay";
			};
			};

			gpio_keys {
			compatible = "gpio-keys";

			bp3 {
			label = "PB_USER";
			gpios = <&pioE 29 GPIO_ACTIVE_LOW>;
			linux,code = <0x104>;
			gpio-key,wakeup;
			};
			};

			leds {
			compatible = "gpio-leds";

			d2 {
			label = "d2";
			gpios = <&pioE 23 GPIO_ACTIVE_LOW>; /* PE23, conflicts with A23, CTS2 */
			linux,default-trigger = "heartbeat";
			};

			d3 {
			label = "d3";
			gpios = <&pioE 24 GPIO_ACTIVE_HIGH>;
			};
			};
			};